Sartorius Cubis MCA125P Series User manual

1000047984
Operating Instructions
Original Operating Instructions
Cubis®
MCA Models
Semimicro, Analytical and Precision Balances

Cubis®MCA Operating Instructions 3
Contents
Contents
1 About these Instructions............................ 6
1.1 Scope ....................................... 6
1.2 Symbols Used................................. 6
1.2.1 Warnings in Operating Instructions........ 6
1.2.2 Other Symbols ......................... 7
1.3 Target Groups................................. 7
2 Safety Instructions ................................. 8
2.1 Intended Use ................................. 8
2.1.1 Modifications to the Device .............. 8
2.1.2 Repairs to the Device.................... 8
2.2 Personnel Qualification......................... 8
2.3 Significance of these Instructions ................ 9
2.4 Functionality of the Device ..................... 9
2.5 Safety Information on the Device ................ 9
2.6 Electrical Equipment ........................... 9
2.6.1 Damage to the Device’s Electrical
Equipment............................. 9
2.6.2 Working on the Device's Electrical
Equipment............................. 9
2.6.3 Power Supply Unit and Power Supply
Cable ................................. 9
2.7 Conduct in an Emergency......................10
2.8 Accessories, Consumables, and Spare Parts .......10
2.9 Glass Breakage...............................10
3 Device Description ................................11
3.1 Device Overview .............................11
3.2 Draft Shield .................................12
3.3 Weighing Pan and Associated Components .......13
3.4 Connections and Components on the
Weighing Module ............................14
3.4.1 Analytical Balance and Precision Balance..14
3.4.2 Semi-microbalance with Electronics
Module ..............................14
3.5 Connections and Components on the
Electronics Module ...........................15
3.6 Connections on the Display and Control Unit .....15
3.7 Safety Equipment ............................16
3.7.1 Protective Caps on the Analytical Balance
and Precision Balance ..................16
3.7.2 Protective Caps on the Electronics
Module ..............................16
3.8 Conformity-assessed Devices ...................17
3.9 Symbols on the Device ........................17
4 Operating Concept................................18
4.1 Operating Elements in the Main Menu...........18
4.2 Operating Elements in Task Management ........19
4.3 Operating Elements in the Weighing Display......20
4.4 Advanced Operator Guidance ..................21
4.5 Messages....................................22
4.6 Status Center ................................23
4.7 Keypad .....................................24
4.8 Status Display of the Buttons ..................24
4.9 Buttons in the Operating Display ...............25
4.9.1 Buttons for Navigation or Organization
in Displays............................25
4.9.2 Buttons for Editing or Managing Entries ..26
4.9.3 Weighing and Print Function Buttons.....27
4.10 Displays in the Operating Display ...............28
4.11 User Management ............................30
4.11.1 User Profiles ..........................30
4.11.2 User Login............................30
4.12 Weighing and Print Profiles ....................30
4.13 Tasks and Applications ........................30
4.14 Menu Structure ..............................31
4.14.1 Main Menu ...........................31
4.14.2 “Settings” Menu .......................31
4.15 Navigating the Menus.........................36
5 Installation.......................................38
5.1 Scope of Delivery.............................38
5.2 Selecting an Installation Site ...................38
5.3 Unpacking the Device .........................39
5.4 Removing the Display and Control Unit ..........39
5.4.1 Positioning the Display and Control Unit ..39
5.5 Connecting the Ethernet Cable .................40
5.6 Preparing Below-balance Weighing .............40
5.7 Installing a Device with an Analytical Draft Shield
or Flat Glass Draft Shield ......................42
5.7.1 Positioning the Weighing Pan and
Associated Components ................42
5.7.2 Installing the Analytical Draft Shield......43
5.7.3 Installing the Flat Glass Draft Shield ......43
5.8 Installing a Device with a Frame Draft Shield .....44
5.8.1 Positioning the Weighing Pan and
Associated Components ................44
5.9 Connecting the Electronics Module
(Only for Semi-microbalance) ..................45
5.10 Installing Palm-operable Keys (Only for Devices
with Motorized Draft Shield) ...................45
5.11 Setting Up the Cable Entry (Only for Devices
with a Manual Analytical Draft Shield)...........45
5.12 Acclimatization ..............................46
6 Getting Started...................................47
6.1 Installing the AC Adapter ......................47
6.2 Connecting the Power Supply ..................47
6.3 Attaching the Protective Caps ..................48
7 System Settings...................................49
7.1 Performing System Settings....................49
7.2 Switching Off the isoCAL Function ..............49
7.3 Assigning a Password .........................49

4 Cubis®MCA Operating Instructions
Contents
7.4 Setting Up Device for Network Printer...........50
7.4.1 Selecting Configuration for Network
Printing ..............................50
7.4.2 Setting Up Device for Network Printer via
Independent Wi-Fi Network .............50
7.4.3 Setting Up Device for Network Printer via
Company Network .....................51
7.4.4 Configure Print Profile .................51
7.5 Parameter List ...............................52
7.5.1 Parameters in the “User Management”
Menu ................................52
7.5.2 Parameters in the “Access Management”
Menu ................................52
7.5.3 Parameters in the “Timer-Controlled
Actions” Menu ........................53
7.5.4 Parameters in the “Weighing and Print
Profile/Weighing” Menu................54
7.5.5 Parameters in the “Weighing and Print
Profiles/YDP30, PDF, CSV, PC Direct,
or SBI Direct” menu....................56
7.5.6 Parameters in the “Connections/
Connectors” Menu .....................58
7.5.7 Parameters in the “Connections/
Network” Menu .......................58
7.5.8 Parameters in the “Connections/
Website/Web Services” Menu ...........59
7.5.9 Parameters in the “Connections/
Interfaces/Serial Communication via
Network” (Ethernet) Menu ..............59
7.5.10 Parameters in the “Connections/
Interfaces/COM-RS232 Interface” Menu ..59
7.5.11 Parameters in the “Connections/
Interfaces/USB-B Interface” Menu .......60
7.5.12 Parameters in the “Connections/
SBI Protocol” Menu ....................61
7.5.13 Parameters in the “Connections/
Climate Module” Menu .................61
7.5.14 Parameters in the “Connections/
Connected Devices/Motion Sensor” Menu
(Only for Connected Motion Sensors) . . . . . 61
7.5.15 Parameters in the “Device Settings/
Date and Time” Menu ..................62
7.5.16 Parameters in the “Device Settings/
Safe Weighing” Menu ..................62
7.5.17 Parameters in the “Device Settings/
minUSP” Menu ........................62
7.5.18 Parameters in the “Device Settings/
Device ID” Menu.......................63
7.5.19 Parameters in the “Device Settings/
Draft Shield” Menu (Only for Devices with
a Motorized Draft Shield) ...............63
7.5.20 Parameters in the “Device Settings/Ionizer”
Menu (Only for Devices with an Ionizer)...63
7.5.21 Parameters in the “Device Settings/
Electronic Signature” Menu .............64
7.5.22 Parameters in the “Device Settings/
Start-up Behavior” Menu ...............64
7.5.23 Parameters in the “Device Settings/
Display Properties” Menu ...............64
7.5.24 Parameters in the “Device Settings/
Sound (Loudspeaker)” Menu.............65
7.5.25 Parameters in the “Device Maintenance”
Menu ................................65
8 Operation ........................................66
8.1 Switching the Device On and Off ...............66
8.2 Logging Users In and Out ......................66
8.3 Leveling the Device ...........................67
8.3.1 Level Device with Motorized
Leveling Feet..........................67
8.4 Opening and Closing the Motorized Draft Shield
(Only for Devices with a Motorized Draft Shield) ..67
8.4.1 Opening Draft Shield by Pressing the
Palm-operated Key ....................67
8.4.2 Defining the Opening Width.............67
8.5 Activating Applications and Adding a Task .......68
8.5.1 Activating Applications .................68
8.5.2 Adding an Application to a Task..........68
8.6 Adding Weighing and Print Profiles to a Task .....69
8.7 Preparing Weighings..........................69
8.8 Weighing ...................................69
8.9 Overview of Calibration, Adjustment,
and Linearization.............................70
8.10 Adjusting with the isoCAL Function .............70
8.11 Internally Calibrating and Adjusting the Device ... 71
8.12 Weighing and Printing with ID Marking..........71
8.12.1 Saving Values for Printouts..............71
8.12.2 Marking Saved Values as Invalid .........72
8.12.3 Marking Saved Values as Valid ...........72
8.12.4 Printing Saved Values ..................72
8.12.5 Exiting the Task .......................73
8.13 Viewing the Data Storage Device ...............73
8.14 Turning the Ionizer On/Off (Only for Devices
with an Ionizer) ..............................73
8.14.1 Setting the Ionizer.....................73
8.14.2 Starting the Ionization Process ..........74
8.14.3 Switching Off the Ionizer ...............74
8.15 Running Applications (Examples) ...............74
8.15.1 Executing the “Unit Change” Function ....74
8.15.2 Running the “Statistics” Application ......75
9 Cleaning and Maintenance.........................76
9.1 Preparing a Device with an Analytical Draft Shield
or Flat Glass Draft Shield ......................76
9.2 Preparing a Device with a Frame Draft Shield .....77
9.3 Cleaning the Device ..........................77
9.4 Assembling and Connecting the Device ..........78
9.5 Maintenance Schedule ........................78
9.6 Performing a Software Update .................78
9.7 Performing a QAPP Center Update ..............79
10 Malfunctions .....................................80
10.1 Warning Messages............................80
10.2 Troubleshooting..............................80

Cubis®MCA Operating Instructions 5
Contents
11 Decommissioning .................................81
11.1 Decommissioning the Device ...................81
12 Transport ........................................81
12.1 Transporting the Device .......................81
13 Storage and Shipping .............................82
13.1 Storage .....................................82
13.2 Returning Device and Parts ....................82
14 Disposal..........................................83
14.1 Information on Decontamination . . . . . . . . . . . . . . . 83
14.2 Disposing of Device and Parts ..................83
14.2.1 Information on Disposal ................83
14.2.2 Disposal..............................83
15 Technical Data....................................84
15.1 Dimensions and Weight .......................84
15.1.1 Semi-microbalance ....................84
15.1.2 Analytical Balance ....................84
15.1.3 Precision Balance ......................84
15.2 Ambient Conditions ..........................85
15.2.1 Installation Site .......................85
15.2.2 Ambient Temperature for the isoCAL
Function .............................85
15.2.3 Protection Class .......................86
15.3 Power Supply ................................87
15.3.1 Device ...............................87
15.3.2 AC Adapter ...........................87
15.3.3 Safety of Electrical Equipment...........88
15.3.4 Electromagnetic Compatibility...........88
15.4 Materials....................................88
15.5 Integrated Clock .............................88
15.6 Backup Battery ..............................88
15.7 Metrological Data ............................89
15.7.1 Models MCA225S | MCA225P |
MCA125S | MCA125P ..................89
15.7.2 Models MCA524S | MCA524P |
MCA324S | MCA324P ..................90
15.7.3 Models MCA224S | MCA124S |
MCA5203S | MCA5203P ................ 91
15.7.4 Models MCA3203S | MCA2203S |
MCA2203P | MCA1203S ................ 92
15.7.5 Models MCA623S | MCA623P |
MCA323S | MCA5202S .................93
15.8 Recommended Calibration Weight ..............94
15.9 isoCAL Function..............................94
15.9.1 Models MCA225S | MCA225P |
MCA125S | MCA125P | MCA324S |
MCA324P | MCA224S | MCA124S |
MCA2203S | MCA2203P | MCA1203S.....94
15.9.2 Models MCA524S | MCA524P |
MCA5203S | MCA5203P | MCA3203S.....95
15.9.3 Models MCA623S | MCA623P |
MCA323S | MCA5202S .................95
15.10 Data Storage Device ..........................95
15.11 Interfaces ...................................96
15.11.1 Specifications for the COM-RS232
Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
15.11.2 Specifications for the USB-A Interface ....96
15.11.3 Specifications for the USB-B Interface ....96
16 Accessories.......................................97
16.1 Accessories ..................................97
16.1.1 Printers and Communication ............97
16.1.2 Displays and Input/Output Elements .....97
16.1.3 Hardware for Pipette Calibration.........98
16.1.4 Filter Balance and Antistatic Accessories ..98
16.1.5 Special Applications....................98
16.1.6 Weighing Tables .......................98
16.1.7 Weighing Accessories ..................99
17 Sartorius Service.................................100
18 Conformity Documents ...........................100
18.1 EU Declaration of Conformity .................100
18.2 Certificate of Compliance.....................102
18.3 FCC Supplier’s Declaration of Conformity .......104

6 Cubis®MCA Operating Instructions
About these Instructions
1 About these Instructions
1.1 Scope
These instructions are part of the device. These instructions apply to the device in the
following versions:
Device Model
Cubis®semi-microbalance, with manual
or motorized draft shield, with or
without ionizer
MCA125P-... | MCA125S-... |
MCA225P-... | MCA225S-...
Cubis®analytical balance, with manual
or motorized draft shield, with or
without ionizer
MCA124S-... | MCA224S-... |
MCA324P-... | MCA324S-... |
MCA524P-... | MCA524S-...
Cubis®precision balance, with frame
draft shield, flat glass draft shield,
manual or motorized draft shield,
with or without ionizer
MCA1203S-... | MCA2203P-... |
MCA2203S-... | MCA3203S-... |
MCA323S-... | MCA5202S-... |
MCA5203P-... | MCA5203S-... |
MCA623P-... | MCA623S-...
Software Version Version, at least
Package release 09-03-02.02.14
QAPP-Center Version 09-06-04.00.06
1.2 Symbols Used
1.2.1 Warnings in Operating Instructions
WARNING
Denotes a danger with the risk that death or severe injury may result if it is not
avoided.
CAUTION
Denotes a hazard that may result in moderate or minor injury if it is not avoided.
NOTICE
Denotes a danger with the risk that property damage may result if it is not avoided.

Cubis®MCA Operating Instructions 7
About these Instructions
1.2.2 Other Symbols
t Required action: Describes actions which must be carried out.
y Result: Describes the result of the actions carried out.
[ ] Text inside brackets refers to control and display items.
[ ] Text inside brackets indicates status, warning, and error messages.
Indicates information for legal metrology for conformity-assessed
(verified) devices. Conformity-assessed devices are also referred to as
“verified” in these instructions.
Figures on the Operating Display
The figures on the operating display of the device may deviate from those in these
instructions.
1.3 Target Groups
These instructions are addressed to the following target groups. The target groups
must possess the specified knowledge.
Target group Knowledge and responsibilities
User The user is familiar with the operation of the device and the
associated work processes. They understand the hazards which may
arise when working with the device and know how to prevent them.
They have been trained in the operation of the device.
The training is carried out by the operating engineer/laboratory
manager or the operator of the device.
Operator The operator of the device is responsible for compliance with safety
requirements and workplace safety regulations.
The operator must ensure that all persons who work with the device
have access to the relevant information and are trained in working
with the device.

8 Cubis®MCA Operating Instructions
Safety Instructions
2 Safety Instructions
2.1 Intended Use
The device is a high-resolution balance, which can be used in laboratories. The device
was developed to accurately determine the mass of materials in liquid, paste,
powder, or solid form.
Appropriate containers must be used for loading each type of material. The device
can be used in stand-alone operation or can be operated on a PC.
The device is exclusively designed for use in accordance with these instructions. Any
further use beyond this is considered improper.
If the device is not used properly: The protective systems of the device may be
impaired. This can lead to unforeseeable personal injury or property damage.
Operating Conditions for the Device
Do not use the device in potentially explosive environments. Only use the device
indoors.
The device may only be used with the equipment and under the operating conditions
described in the Technical Data section of these instructions.
2.1.1 Modifications to the Device
If the device is modified, for example by attaching extra components: Device safety
may be affected, or the device may cease to be compliant.
If you have any queries regarding modifications to the device, contact Sartorius.
2.1.2 Repairs to the Device
Device repairs may only be carried out by persons with appropriate specialized
knowledge of the device. If the device is not repaired by a specialist: The safety of
the device may be impaired or the quality marks may lose their validity.
We recommend that any repair work, even that not covered by the warranty, is
carried out by Sartorius Service or after consulting with Sartorius Service.
2.2 Personnel Qualification
If people who do not have sufficient knowledge on the safe handling of the device
carry out work on the device: Those people may injure themselves or other people
nearby.
tEnsure that all individuals working on the device possess the necessary
knowledge and qualifications (see Chapter “1.3 Target Groups”, page 7.)
tIf a particular qualification is required for the actions described: Have these
activities carried out by the required target group.
tIf no qualification is required for the actions described: Have these activities
carried out by the “user” target group.

Cubis®MCA Operating Instructions 9
Safety Instructions
2.3 Significance of these Instructions
Failure to follow the instructions in this manual may have serious consequences, e.g.
danger to individuals.
tRead the instructions carefully and in full.
tEnsure that the information contained in these instructions is available to all
individuals working on the device.
tRetain the instructions.
tIf these instructions are lost, request a replacement or download the latest
version from the Sartorius website (www.sartorius.com).
2.4 Functionality of the Device
A damaged device or worn parts may lead to malfunctions or cause hazards which
are difficult to recognize.
tOnly operate the device when it is safe and in perfect working order.
tHave any damage repaired immediately by Sartorius Service.
2.5 Safety Information on the Device
Symbols, e.g. warnings, safety stickers, are safety information for the handling of the
device. Missing safety information may lead to serious injuries.
tDo not conceal, remove, or modify the symbols.
tReplace the symbols if they become illegible.
2.6 Electrical Equipment
2.6.1 Damage to the Device’s Electrical Equipment
Damage to the electrical equipment of the device, e.g. damage to the insulation, can
be life-threatening. Contact with parts under voltage represents a direct danger to
life.
tIf the device’s electrical equipment is defective, disconnect the device from the
power supply and contact Sartorius Service.
tKeep live parts away from moisture. Moisture can cause short-circuits.
2.6.2 Working on the Device's Electrical Equipment
Only Sartorius Service personnel may work on or modify the electrical equipment of
the device. The device may only be opened by Sartorius Service personnel.
2.6.3 Power Supply Unit and Power Supply Cable
Serious injury can result, e.g. from electric shocks, if an unsuitable and inadequately
dimensioned power supply cable or unsuitable AC adapter is used.
tOnly use the original power supply cable and AC adapter.
tIf the AC adapter or power supply cable must be replaced: Contact Sartorius
Service. Do not repair or modify the power supply unit or power supply cables.

10 Cubis®MCA Operating Instructions
Safety Instructions
2.7 Conduct in an Emergency
If there is immediate danger of personal injury or if there is a risk of damage to the
device, e.g., due to malfunctions or dangerous situations, the device must be
immediately taken out of operation.
tDisconnect the device from the power supply by disconnecting the power supply
cable.
tMalfunctions should be remedied by Sartorius Service.
2.8 Accessories, Consumables, and Spare Parts
Unsuitable accessories, consumables, and spare parts can adversely affect
functionality and safety, and have the following consequences:
− Risk of injury to persons
− Damage to the device
− Device malfunctions
− Device failure
tOnly use approved accessories and spare parts supplied by Sartorius.
tOnly use accessories, consumables, and spare parts that are in proper working
order.
2.9 Glass Breakage
Glass components can break if they fall or are handled incorrectly. Glass fragments
can cause cuts.
tOnly lift the device by its base, not by the draft shield.
tWhen lifting and transporting, ensure that no personnel or objects are in the
way.
tOnly operate the operating display with your fingers. Do not use pointed or sharp
objects.

Cubis®MCA Operating Instructions 11
Device Description
3 Device Description
3.1 Device Overview
2
7
8
1
3
4
9
5
Fig.1: Semi-microbalance with motorized draft shield with ionizer and electronics module (example)
Pos. Name Description
1 Weighing chamber
2 Manufacturer’s ID label Not depicted
3 Weighing module
4 Electronics module Only for semi-microbalances with electronics module
5 Leveling foot Motorically adjustable
6 Palm-operated key Opens and closes the side and upper panel of the draft shield
7 Display and control unit
8 Operating display Touchscreen
9 Level
6
6

12 Cubis®MCA Operating Instructions
Device Description
3.2 Draft Shield
4
7
6
32
5
1
Fig.2: Precision balance with frame draft shield, analytical balance with motorized analytical draft shield, and precision balance with manual analytical draft shield
(example)
Pos. Name Description
1 Frame draft shield Is placed on the shield plate.
2 Analytical draft shield Can be opened at the door handle of the upper panel or at the door handles of the side
panels. Is motorized in some models.
3 Housing back plate Manufactured from metal and plastic parts
4 Upper draft shield panel Used to open the upper panel. Can be opened manually and is motorized in some models.
5 Rear panel Glass
6 Front panel Glass
7 Side panel Can be opened manually and is motorized in some models.

Cubis®MCA Operating Instructions 13
Device Description
3.3 Weighing Pan and Associated Components
2
1
3
4
1
3
4
1
2
4
3
Fig.3: Precision balance with frame draft shield, analytical balance with manual analytical draft shield, and precision balance with manual analytical draft shield
(example)
Pos. Name Description
1 Weighing pan
2 Pan support Only for models with pan support
3 Shield plate
4 Pan retainer

14 Cubis®MCA Operating Instructions
Device Description
3.4 Connections and Components on the Weighing Module
3.4.1 Analytical Balance and Precision Balance
1 2 3 4 5 6 7 8
Fig.4: Connections on the weighing module of the analytical balance and precision balance (example)
Pos. Name Description
1 On key Switches the device on from standby mode.
2 USB-A connection For USB accessories, e.g. printers, USB mass storage devices, barcode scanners
3 USB-B connection For connection to a PC
4 COM-RS232 connection 9-pin, for connection to a PC or PLC
5 Access switch Protects the device from changes to the device settings. Is sealed for conformity-
assessed devices.
6 Peripheral connection For connecting Sartorius accessories
7 Power supply For connection to the power supply
8 Slot For attaching a “Kensington” anti-theft device
3.4.2 Semi-microbalance with Electronics Module
1 2
Fig.5: Connections on the weighing module of the semi-microbalance with electronics module (example)
Pos. Name Description
1 Electronics module connection For connecting the electronics module to the weighing module
2 Slot For attaching a “Kensington” anti-theft device

Cubis®MCA Operating Instructions 15
Device Description
3.5 Connections and Components on the Electronics Module
1 2 3 4 5 8 7
6
Fig.6: Connections on the electronics module (example)
Pos. Name Description
1 On key Switches the device on from standby mode.
2 USB-A connection For USB accessories, e.g. printers, USB mass storage devices, barcode scanners
3 USB-B connection For connection to a PC
4 COM-RS232 connection 9-pin, for connection to a PC or PLC
5 Access switch Protects the device from changes to the device settings. Is sealed for conformity-
assessed devices.
6 Peripheral connection For connecting Sartorius accessories
7 Weighing module connection For connecting the electronics module to the weighing module
8 Power supply For connection to the power supply
3.6 Connections on the Display and Control Unit
1 2 3
Fig.7: Connections on the display and control unit (example)
Pos. Name Description
1 USB-C connection For USB mass storage devices
2 USB-A connection For USB accessories, e.g. printers, USB mass storage devices, barcode scanners
3 Ethernet connection For connecting an Ethernet cable

16 Cubis®MCA Operating Instructions
Device Description
3.7 Safety Equipment
3.7.1 Protective Caps on the Analytical Balance and Precision Balance
1 2 3 4 5
Fig.8: Protective caps on the weighing module of the analytical balance and precision balance
Pos. Name Description
1 Protective cap for USB-A connection Plastic attachment hood, fastened to the device.
2 Protective cap for USB-B connection Plastic attachment hood, fastened to the device.
3 Protective cap for COM-RS232
connection
Removable plastic sealing cap.
4 Protective cap for access switch Removable plastic sealing cap.
5 Protective cap for peripheral connection Removable plastic sealing cap.
3.7.2 Protective Caps on the Electronics Module
1 2 3 4 5
Fig.9: Protective caps on the electronics module
Pos. Name Description
1 Protective cap for USB-A connection Plastic attachment hood, fastened to the device.
2 Protective cap for USB-B connection Plastic attachment hood, fastened to the device.
3 Protective cap for COM-RS232
connection
Removable plastic sealing cap.
4 Protective cap for access switch Removable plastic sealing cap.
5 Protective caps for peripheral
connections
Removable plastic sealing caps.

Cubis®MCA Operating Instructions 17
Device Description
3.8 Conformity-assessed Devices
Some settings of conformity-assessed models are protected against user changes,
e.g. “external calibration” for devices in accuracy class II. This measure is intended to
ensure the suitability of the devices for use in legal metrology.
3.9 Symbols on the Device
1
Fig.10: ID label on the device (example)
Pos. Name Description
1 Manufacturer’s ID label Displays the metrological data of the device.
Conformity-assessed models only
Symbol Meaning
During operation, parts in the device may be live. Only electricians
may have access to and work on these parts, such as for
maintenance and repairs.

18 Cubis®MCA Operating Instructions
Operating Concept
4 Operating Concept
4.1 Operating Elements in the Main Menu
4
2
1
3
Fig.1: Operating elements in the main menu (example)
Pos. Name Description
1 Navigation and function bar − Enables navigation and searching in menus and lists.
− In the “Settings” Menu: Displays the name of the menu.
2 Available tasks Displays all tasks available for the active user.
3 Function bar Displays available submenus and operating functions for the current display
and current user.
4 Task Starts the described task.

Cubis®MCA Operating Instructions 19
Operating Concept
4.2 Operating Elements in Task Management
2
1
Fig.2: Operating elements in Task Management (example)
Pos. Name Description
1 Navigation and function bar − Enables navigation and searching in menus and lists.
− Enables the addition of tasks.
− Opens the QAPP center.
− Displays the name of the menu.
2 Available tasks − Displays all available tasks.
− Opens a summary of the properties for the displayed task.

20 Cubis®MCA Operating Instructions
Operating Concept
4.3 Operating Elements in the Weighing Display
6
12
21 3 4 5
7
9
8
10
11
Fig.3: Weighing display (example)
Pos. Name Description
1 Application symbol Displays the symbol for the active application.
2 Task name Displays the name of the active task.
3 Date display Displays the current date.
4 User name Displays the name of the active user profile.
5 Time display Displays the current time.
6 Navigation bar Enables navigation in menus.
7 Metrological data
8 Labeled points Labels the differentiated points.
9 Weight value display In the selected unit and resolution
10 Weighing unit Displays the selected unit, e.g. grams, [g].
Enables the unit and resolution to be selected.
11 Bar graph Displays the measured value as a percentage of weighing capacity utilization.
12 Function bar Displays available operating functions for the current display.