Sartorius PMA.Power User manual

1000025284
Operating Instructions
Sartorius PMA.Power
Model PMA35001-Y
Electronic Paint-mixing Scale for Use in Zone 2 Hazardous Areas

2
General View of PMA35001-Y (PMA.Power)
For Use in Zone 2 Hazardous Areas
1 Display and control unit
2 Display
3 UZero/tare key
4 IToggle key depending on the menu setting:
You can configure the PMA35001-Y menu to
enable toggling between grams (g) and parts
per pound (p)
5 Leveling foot
6 KFactor key for paint-mixing applications
7 c[Clear] key and [REC] key for
paint-mixing applications
8 Lkey [ENTER] and [MEM] key for paint-
mixing applications
9 Mounting bracket for display and control unit
10 Interface (25-contact D-Sub socket)
11 Grounding terminal
12 Power cord with plug
13 Level indicator
14 Cable connection
15 Load plate
16 S‘Down’ key
17 Power supply and data cable for the display
and control unit
18 R‘Up’ key
19 QOn/Off (standby) key
Symbols
The following symbols are used in these
instructions:
§indicates required steps
$indicates steps required only under certain
conditions
> describes what happens after you have
performed a particular step
– indicates an item in a list
!indicates a hazard
1
2
3
4
5
6
7
8
10
19
14
9
13
15
12
16
17
18
11

3
Contents
General View of the Equipment� � � � � � 2
Contents � � � � � � � � � � � � � � � � � � � � � � 3
Intended Use � � � � � � � � � � � � � � � � � � � 3
Warnings and Safety Precautions � � � � 3
Getting Started� � � � � � � � � � � � � � � � � � 6
Operation� � � � � � � � � � � � � � � � � � � � � � 8
Applications � � � � � � � � � � � � � � � � � � � � 9
Calibration/Adjustment� � � � � � � � � � � � 12
Menu Settings � � � � � � � � � � � � � � � � � � 13
Troubleshooting Guide � � � � � � � � � � � � 18
Care and Maintenance � � � � � � � � � � � � 19
Disposal � � � � � � � � � � � � � � � � � � � � � � � 20
Interface Description� � � � � � � � � � � � � � 21
Serial Number Coding ������������22
Technical Data � � � � � � � � � � � � � � � � � � 23
Accessories � � � � � � � � � � � � � � � � � � � � � 23
Documents� � � � � � � � � � � � � � � � � � � � � 24
Intended Use
The PMA35001-Y (PMA�Power series)
scale is specially designed for use in
paint-mixing applications� This scale
can be operated via the keypad in stand-
alone operation or using application
software (such as a paint-mixing program
from a paint manufacturer) installed
on a connected PC�
If you wish to create your own applica-
tion software, Sartorius can supply the
required drivers for DOS or Windows
operating systems�
Note:
– Make sure that you read the warnings
and safety precautions carefully before
installing and operating your
PMA35001-Y scale�
Note:
Improper use or handling can result in
damage and/or injury� The scale should
only be installed and operated by qualified
personnel� When operating the equipment
in a Zone 2 hazardous area, make sure you
observe the warnings and safety precautions
in their entirety during installation and oper-
ation, as well as while performing mainte-
nance and repair work on the equipment� All
relevant standards, regulations, occupational
safety requirements and environmental pro-
tection laws valid in your country must be
observed� Please ask your supplier regarding
the regulations applicable in your country�
It is important that all personnel using the
equipment understand this warning and
safety information and have access to all rel-
evant documents at all times� Furthermore,
the warning and safety information sup-
plied with any electrical equipment, such as
peripheral devices, must be observed as well�
These warnings and safety precautions must
be supplemented by the operator as required�
All operating personnel must be informed
of any additions to these instructions� Make
sure the equipment is accessible at all times�
General Provisions for Installing the
PMA35001-Y
PMA35001-Y models meet the requirements
defined in EC Directive 2014/34/EU for
Class II, Category 3G equipment�
The safety instructions listed in drawing
2444395 (refer to Documents) must be
strictly observed�
Warnings and
Safety Precautions

4
– PMA35001-Y models meet the require-
ments of the EC Directives for electro-
magnetic compatibility and electrical
safety (refer to the chapter on
CE Marking)�
The area of use for the PMA35001-Y is
defined in the included documentation�
All restrictions listed in the included
documentation must be observed�
– Operating the PMA35001-Y beyond
the restrictions indicated is not permitted,
and is considered use of the equipment
for other than its intended purpose� Any
installation work that does not conform
to the instructions in this manual results
in forfeiture of all claims under the
manufacturer’s warranty�
– If the equipment is modified by any-
one other than persons authorized by
Sartorius, authorization is withdrawn
and all claims under the manufacturer’s
warranty are forfeited�
– The installation of the PMA35001-Y in
a hazardous area must be carried out by a
certified electrician�
A certified electrician is someone who is
familiar with the assembly, start-up and
operation of the system�
He is also familiar with all relevant
guidelines and regulations, and has the
required qualifications for performing the
installation� If you need assistance, con-
tact your Sartorius dealer or the Sartorius
Service�
Connect all equipment, including periph-
eral devices, to the equipotential bonding
conductor�
– The display values can be impacted when
subjected to extreme electromagnetic
influence�
When the negative influence has sub-
sided, the scale will again be fully
operational�
– The equipment must only be used
indoors�
– Make absolutely sure to disconnect the
scale from power (unplug the power
cord) before you connect or disconnect
a peripheral device (printer or PC) to or
from the interface port�
– If you use cables purchased from another
manufacturer, check the pin assignments
in the cable against those specified by
Sartorius before connecting the cable to
Sartorius equipment, and disconnect any
wires that are assigned differently� The
operator shall be solely responsible for
any damage or injuries that occur when
using cables not supplied by Sartorius�
– The power connection must be made in
accordance with the regulations appli-
cable in your country� If you need assis-
tance, contact your Sartorius dealer or the
Sartorius Service� Any installation work
that does not conform to the instructions
in this manual results in forfeiture of all
claims under the manufacturer’s warranty�
– To avoid generating static electricity
when using the dust cover:
The cover should only be cleaned using
a moist cloth�

Leveling the Weighing Platform
Purpose:
– To compensate for uneven areas at the place of
installation
– To ensure that the equipment is placed in a perfectly
horizontal position for consistently reproducible
weighing results
Always level the weighing platform again any time
after it has been moved to a different location�
§Level the weighing platform using the four leveling
feet� Turn the feet until the air bubble is centered
in the level indicator�
§Check to ensure that all leveling feet rest securely
on the work surface�
> Each of the leveling feet must support an equal
load�
> Adjusting the leveling feet:
To raise the weighing platform, extend the leveling
feet (turn counterclockwise)�
To lower the weighing platform, retract the leveling
feet (turn clockwise)�
5
For the User
– Always make sure the equipment is
disconnected from AC power before
performing any installation, cleaning,
maintenance or repair work on the scale�
– If you see any indication that the scale
cannot be operated safely (for example,
due to damage), disconnect the scale
from AC power and prevent use of the
equipment for the time being�
– Chemicals (e�g� gases or liquids) that can
corrode and damage the inside or outside
of the device must be kept away from the
equipment�
Handle the equipment and any accesso-
ries in accordance with the IP rating (IEC/
EN 60529)�
– The casing on all connecting cables, as
well as the casing on wires inside the
equipment housing, is made of PVC or
rubber�
– The permitted ambient temperature range
during operation is 0°C to +40°C�
Make sure that the equipment is prop-
erly ventilated to prevent the buildup of
excessive heat�
– Only use original Sartorius spare parts�
– Never use a hammer to close a paint can
while is it still on the load plate, as this
will damage the weighing system�

6
Getting Started
§Unpack the scale carefully�
§After unpacking the equipment, inspect the device
immediately for any visible damage that may have
been caused by rough handling during shipment�
Package Contents
– Scale
– Load plate
– Adapter cable
Setting up the Scale
Choose a suitable location where your scale will not
be exposed to drafts, heat radiation, moisture or
vibrations�
Make sure that you read these operating instructions
carefully before connecting the scale to the power
supply�
!Observe all warnings and safety precautions�
!Caution
The scale must be grounded before installing
the device in a Zone 2 hazardous area� Root the
grounding wire (cross section 4mm² in minimum)
through the eyelet� Connect the cable to the
grounding terminal (11); see illustration�
§Place the load plate on the scale�
°C

7
Connecting to AC Power
The equipment is powered through the scale’s power
cord� Make sure that the voltage rating printed on
this unit is identical to your local line voltage�
If the stated supply voltage or the plug design of the
power cord does not comply with the standard you
use, please inform your nearest Sartorius representa-
tive or your supplier�
Installation
The device must be plugged into a properly installed
wall outlet which has a protective grounding
conductor (PE) and a max� (16A) fuse�
§Connection of the power cord plug (12) outside of
the hazardous area or mechanically secured (refer to
“Safety Information” documents)�
§Plug the power cord into a wall outlet (mains)�
Observe all warnings and safety precautions�
!See also: “Safety Instructions” documents� Install
the scale in such a way or protect the power cord in
such a way that mechanical tensile load on the plug
and cable gland (on the scale) is prevented!
Note:
When installing the scale in a Zone 2 hazardous
area, connectors may only be plugged in or discon-
nected in a currentless/dead-voltage state�
Disconnect the scale from the power line before
connecting peripheral devices (printer, PC) to the
data interface of the device�
§When connecting peripheral devices (printer, PC) to
the scale’s data interface, make sure that the screws
on the data plug are tightened securely�
!Observe all warnings and safety precautions�
See also: “Safety Instructions” documents�

8
Operation
Weighing with One Decimal Place
Place an empty paint can on the load plate�
Press the Ukey (Zero/tare) (3)�
The display shows »0.0 g«� Pour the first component
of your formula into the can and read off the weight when
the stability symbol (in this example) »g« is displayed�
Add the other components up to the desired weight
(formula)�
Remove the filled paint can from the load plate�
Never use a hammer to close a paint can while is it still on
the load plate, as this will damage the weighing system�
Press the Qkey (19) to turn
on the scale� Once the scale has been
turned on, it will run an
automatic self-test� This is
concluded with the readout
0.0 g�
If a different value is
displayed: Tare the scale
using the Ukey (Zero/
tare) (3)�

9
Applications
Formulation Mode (Calculation by a Factor)
This mode enables you to weigh in amounts that are smaller or larger than that of your
basic formula for a specific paint color (e�g� 250 ml of a 1 l formula)� You can select
various factors (amounts) by pressing the Kfactor key (6):
0�5 1�0 1�5 2�0 2�5 3�0 3�5 4�0 4�5 5�0 10�0 15�0 20�0 25�0�
By pressing the ‘Up’ (18) Rkey
or ‘Down’ (16) Skey
you can change the value – in 1�0 increments, as a factor of 5�0
– in 0�1 increments, as a factor of 1�0
or – 0�01 increments, up to a factor of 1�0�
Note:
A flashing arrow non the display indicates that the weight value displayed is not valid
in legal metrology (i�e�, not legal for trade)�
Example:
As you pour the components of your formula, the weight is displayed in »g«�
Let’s suppose you want to weigh 3 kg for a basic formula that has a total of 1kg, and you
don’t want to have to manually recalculate the individual components of the formula�
The basic formula for 1 kg is:
250 g First component
+ 250 g Second component
+ 500 g Third component
Total: 1000 g
1� Place the empty paint can on the load
plate and tare the scale� 2� Press the Kfactor key (6) repeatedly to
set the factor to “3�0” for this example�

10
Weighing Using the Recalculation Mode
Let’s suppose that you poured in too much of one color component for a given formula (in
this example, a 4-component recipe)�
This example further assumes that you previously poured in all of the other amounts exactly
according to each of the values you entered and saved by pressing the Lkey [MEM] (8)�
To correct for the overpour, press the Skey (16) to start the recalculation program; Cflashes
on the display� Use the Rkey (18; up) or Skey (16; down) to correct the value so that it
matches the amount called for in the formula� Then press L[MEM] (8) to have the scale
calculate the amount to be added for each of the components that were already poured�
The display shows the amounts required to correct the formula up to the point at which the
overpour occurred� After the correction has been completed, you can continue filling the
remaining components�
Note:
You can correct overpours as often as needed�
Keep in mind that the total quantity of paint at the conclusion of filling increases each time
you correct a component� Press the ckey (7) to check how much the total quantity will be�
The Cstands for “Correction factor�”
A flashing arrow non the display indicates that the weight value displayed is not valid in
legal metrology (i�e�, not legal for trade)�
3� »3.0« appears next to the weight readout�
4� Slowly pour in the first component until the
display shows »250 g«�
5� Pour in the second component until »500 g« is
displayed�
6� Pour in the last component until »1000 g« is
displayed�
This concludes the recalculation example�
According to the display, exactly 1000 g was poured
in, but the paint can actually contains 3 kg by weight
in accordance with the factor you selected (3)�
The procedure is the same for any other conversion
factor�

11
3. Add first component
+ 50�0 g
2. Press the Ukey (zero/
tare; (3))�
0�0 g
Example (Cumulative Weighing)
1. Center an empty paint can
on the load plate (15)�
+ 118�0 g
4. Press the Lkey [MEM] (8)
STO 01 5. Add the second component
+ 110�0 g 6. Press the Lkey [MEM] (8)
STO 02
7. Add the third component
+ 203�0 g
Oops! You poured in too
much� The correct value for
the formula is 200�0 g�
8. Press the Skey (16) to start
the recalculation mode� A »C«
(“Correction”) flashes on the
display�
9. Press the Skey (16) repeat-
edly to correct the value�
+ 200�0 g
10. Press the Lkey [MEM]
key (8)
COR 01
11. The readout shows the
amount of the first compo-
nent to be added, and “C1”
is shown in the upper right-
hand corner of the display�
–1�7 g�
12. Add until value reaches
0�0 g�
0�0 g
13. Press the Lkey [MEM] key
COR 02 14. The readout shows the
amount of the second com-
ponent to be added, and
“C2” is displayed� – 2�0 g
15. Add until value reaches
0�0 g�
0�0 g
16. Press the Lkey [MEM] key
(8)� The scale returns to the
formulation program� »C«
is no longer displayed�
+ 200�0 g�
17. Press the ckey (7) [REC]
to view the factor by which
the total weight will exceed
the original target defined in
the recipe� (C= “Correction;”
in this example, 1�03)�
(Total weight = original
target +correction factor)
18. Add fourth component
+1000�0 g
This concludes the
recalculation example�

12
Calibration/Adjustment
You can calibrate/adjust the scale by pressing the
Ukey (Zero/tare) (3)�
Calibration weights: 10,000 g; resolution: ± 0�016 g�
Always allow approximately 30 minutes for the scale
to warm up after connecting it to AC power and
before performing calibration/adjustment�
Press the Ukey (Zero/tare) (3) for 2 seconds;
“10000” is displayed�
Release the key�
Center the calibration weight on the load plate (15)�
Adjustment is performed automatically�
Remove the calibration weight�

13
Menu Settings
Accessing the SETUP Menu
Example:
Menu item: Adapting the Scale to Ambient Conditions
§ Hold down the Lkey [ENTER] for approximately
2 seconds; “SETUP” is displayed�
§Use the RS keys to select the desired menu item
on this level�
§Press the Lkey [ENTER] to select the next menu
level�
§The second menu level is displayed� Use the RS
keys to select the desired menu item on this level�
§Press the L key [ENTER] to select the next menu
level�
§The third menu level is displayed� Use the RS keys
to select the desired menu item on this level�
§Press the Lkey [ENTER] to select the next menu
level�
§The fourth menu level is displayed� Use the RS
keys to select the desired menu item on this level�
This concludes the example�
§Press the Lkey [ENTER]; ois displayed, indicating
that this item is set�
§Press ckey (Clear) repeatedly to exit the menu�
Note:
Contact your local Sartorius office for a detailed list
of the menu codes�

14
Configuring the Main Menu Settings
§Hold down the Lkey [ENTER] for approximately 2 seconds; “SETUP” is displayed�
Level 1
SETUP
Language Setting
Level 1 Level 2
LANGUAGE §Press the Rkey to select LANGUAGE
§ Press the Lkey [ENTER]
oGERMAN § Press the RS keys to select a language
ENGLISH § Press the L key [ENTER];
FRENCH oindicates the active setting
ITALIAN § Press the ckey repeatedly to exit
etc� the menu
Default Unit: Grams or Parts per Pound
The default settings is active when the scale is switched on; defined under “SETUP > SCALE > UNIT”:
Level 1 Level 2 Level 3 Level 4
SETUP §Press the Lkey [ENTER]
SCALE § Press the Lkey [ENTER]
UNIT § Use the RS keys to select the desired
setting; e�g�, “UNIT”
oGRAMS §Press the Lkey [ENTER]
PT./PD. § Use the RS keys to select the desired
unit; e�g�, “GRAMS”
IActivating the Toggle Key
When the toggle key I(4) is active, you can configure it to toggle the weight unit between grams
and parts per pound� The unit is toggled when the key is pressed�
Level 1 Level 2 Level 3 Level 4
SETUP § Press the Lkey [ENTER]
APPLICATION §Use the RS keys to select
“APPLICATION”
§Press the Lkey [ENTER]
TOGGLE §Use the RS keys to select “TOGGLE”
OFF § Press the Lkey [ENTER]
o ON §Use the RS keys to select “ON”
§ Press the Lkey [ENTER]; oindicates
the active setting
§ Press the ckey (Clear) repeatedly
to exit the menu�

15
IConfiguring the Toggle-key Function
Pressing the toggle key I(4) toggles the scale between the default unit (defined under SETUP >
SCALE > UNIT; see page 13) and the unit defined as follows under SETUP > APPLICATION > UNIT�
Level 1 Level 2 Level 3 Level 4
SETUP §Press the Lkey [ENTER]
APPLICATION §Use the RS keys to select
“APPLICATION”
UNIT §Press the Lkey [ENTER], press Sto
select “UNIT” and press Lto confirm�
o PT./PD. §Use the RS keys to select the desired
unit; e�g�, “PT�/PD�”
GRAMS §Press the Lkey [ENTER]; oindicates
the active setting�
§ Press the c key (Clear)
Activating the “LOCK” Function
The LOCK function protects the scale from unauthorized use� When this function is active, the scale
readout shows weight values only when there is active communication between the scale and a PC�
If communication is interrupted, the readout goes blank and the display shows a padlock symbol�
Activation of the LOCK function is configured under “EXTRAS�”
Level 1 Level 2 Level 3 Level 4
SETUP § Press the Lkey [ENTER]
EXTRAS § Use the RS keys to select “EXTRAS”
§ Press the L key [ENTER]
LOCK § Use the RS keys to select “LOCK”
§ Press the Lkey [ENTER]
OFF § Use the RS keys to select ON and
oON press Lto confirm
§ Press the ckey (Clear) repeatedly to exit
the menu�

16
Configuring Password Protection
In addition to the LOCK function, you can configure password protection for additional security�
With this feature, the LOCK function can be deactivated only by entering the password you configure�
The password is numeric and can have up to 6 digits� Use the RS keys to select the digits
(0 through 9) for your password� The password is hidden on the readout; only dashes (“------”) are
shown� The first dash flashes to prompt input� Press the RS keys as needed to select the desired
digit (0 to 9) and then press the Lkey [ENTER] key� The digit is stored and the second dash flashes
on the display� Repeat the input procedure as described for the first digit� To store a space as
a character in the password, press the Lkey [ENTER] while the corresponding dash is flashing�
Once all 6 characters have been stored, press the Lkey [ENTER] to store the password�
Note:
Keep a copy of your password in a safe place�
The LOCK function can be deactivated only with this password�
Level 1 Level 2 Level 3
INPUT §Use the RS keys to select “INPUT”
PASSWORD § Press the Lkey [ENTER]
§Press the Lkey [ENTER]
PW.NEW §Use the RS keys to select “PW�NEW”
-------- §Enter the desired password and press the
Lkey [ENTER]
§Press the ckey (Clear) repeatedly to exit
the menu
Changing the Password
To define a new password, the existing password must be entered first in the SETUP menu under
“PASSWORD�” “PW�OLD” prompts this input� Once the old password is entered, the “PW�NEW”
prompt is shown automatically� Enter the new password or press Lat each position to enter spaces�
The display shows spaces�
Note:
Entering 6 spaces deletes the password, which deactivates the password function�
Level 1 Level 2 Level 3
INPUT §Use the RS keys to select “INPUT”
PASSWORD §Press the Lkey [ENTER]
PW.OLD §Press the Lkey [ENTER]
-------- §Enter the existing (old) password
PW.NEW > After the old password have been entered
correctly, “PW�NEW” is displayed�
-------- §Enter the desired password and press
the Lkey [ENTER]
§Press the ckey (Clear) to return
to the menu

17
Configuring Text Length (“LONG” or “SHORT”)
You can define the length of the operator guidance texts shown on the display�
Level 1 Level 2 Level 3 Level 4
SETUP § Press the Lkey [ENTER]
EXTRAS §Use the RS keys to select “EXTRAS”
§ Press the L key [ENTER]
TEXTS §Use the RS keys to select “TEXTS”
§ Press the Lkey [ENTER]
LONG § Use the RS keys to select “SHORT”
o SHORT and press Lto confirm
§Press the ckey (Clear) repeatedly
to exit the menu
Resetting the Scale: “RESET”
You can restore the factory settings in the scale�
Note:
If you have activated the password function, this feature is password-protected�
Level 1 Level 2 Level 3 Level 4
SETUP § Press the Lkey [ENTER]
RESET §Use the RS keys to select “RESET”
§ Press the L key [ENTER]
MENU §Use the RS keys to select “MENU”
§Press the L key [ENTER]
YES § Use the RS keys to select “YES”
o NO § Press the Lkey� Factory settings are
restored� “MENU” is displayed
§Press the ckey (Clear) repeatedly
to exit the menu
Code Settings
Select the “CODES” menu item to have menu items identified by numeric codes rather than texts�
Level 1 Level 2
LANGUAGE §Press the Rkey to select LANGUAGE
§ Press the L key [ENTER]
GERMAN §Use the RS keys to select “CODES”
etc� §Press the Lkey [ENTER]; oindicates
oCODES the active setting
§ Press the ckey (Clear) repeatedly
to exit the menu
Note:
Contact your local Sartorius office for a detailed list of the menu codes�

Troubleshooting Guide
Problem Cause Solution
No segments appear – No AC power is available – Check the AC power supply
on the display
The weight readout – No load plate on the scale – Position the load plate
shows “Low”
The weight readout – Weighing capacity exceeded – Unload the scale
shows “High”
The weight readout – Unstable ambient conditions – Set up the scale in another
changes constantly area
– Too much vibration, or the – Access the menu to select
scale is exposed to a draft the appropriate code for the
ambient conditions
(see “Menu Settings”)
The weight readout – The sample is not stable – Tare the scale before weighing
is obviously incorrect – Scale not tared before
weighing
No weight value is – PC connection to the scale has – Access the menu settings to
shown and the been interrupted activating deactivate the LOCK function
padlock symbol the LOCK function
is displayed – Check the connection
18

Care and Maintenance
Cleaning
!Never use concentrated acids, alkali
solutions or pure alcohol to clean the
equipment�
!Do not allow liquids to penetrate the
equipment housing�
$Use a brush or a soft, dry, lint-free cloth
to clean the scale�
Storage and Shipping Conditions
$The packaging used for shipping your
Sartorius equipment is optimally designed
to prevent damage during transport�
It is a good idea to save the box and all
parts of the packaging for future storage
or shipment of the equipment�
$Storage temperature: –20°C ��� +70°C
$Allowable humidity during storage:
max� 90%
$Please refer to the information under
“Safety Inspection” below�
Safety Inspection
Safe operation of the scale is no longer
ensured in the following cases:
– There is visible damage to the AC
adapter/power supply or cables
– The equipment no longer functions
properly
– The equipment has been stored for
a relatively long period under unfavorable
conditions
– The equipment has been subjected to
rough handling during shipment
§Observe all warnings and safety precau-
tions�
In this case, notify the Sartorius Service
or the International Technical Support
Unit based in Goettingen, Germany�
Maintenance and repair work may only
be performed by authorized Sartorius ser-
vice technicians who have access to the
required maintenance manuals and have
received the necessary training�
19

20
Disposal
Information on Decontamination
The device does not contain any hazard-
ous materials that would necessitate spe-
cial disposal actions�
Contaminated samples used during the
process are potentially hazardous materi-
als that could cause biological or chemi-
cal hazards�
If the device has come into contact with
hazardous substances: Steps must be
taken to ensure proper decontamination
and declaration� The operator is responsi-
ble for adhering to local government reg-
ulations on the proper declaration of
transport and disposal and the proper
disposal of the device�
!Warning
Risk of injury due to contaminated
devices!
Devices contaminated with hazardous
materials (NBC contamination) will not be
accepted by Sartorius for repair or disposal�
Dispose of Device and Parts
Information on Disposal
The device and the device accessories
must be disposed of properly by disposal
facilities�
A lithium cell battery, type CR2032, is
installed inside the device� Batteries must
be disposed of properly by disposal facili-
ties�
The packaging is made of environmental-
ly friendly materials that can be used as
secondary raw materials�
Disposal
Requirements
The device has been decontaminated�
Procedure
– Dispose of the device� Follow the disposal
instructions on our website
(www�sartorius�com)�
– Dispose of the packaging in accordance
with local government regulations�