Satec Expertmeter PM180 User manual

expertmeter™
High Performance Analyzer
PM180
IEC 61850 Communications Protocol
Reference Guide
BG0523 Rev. A2

2
Every effort has been made to ensure that the material herein is complete and accurate.
However, the manufacturer is not responsible for any mistakes in printing or faulty
instructions contained in this book. Notification of any errors or misprints will be received
with appreciation.
For further information regarding a particular installation, operation or maintenance of
equipment, contact the manufacturer or your local representative or distributor.
REVISION HISTORY
A1 Oct 2012 Initial release
A2 Feb 2013 Added configurable measurement units, datasets and RCBs, and generating
CID files.

3
Table of Contents
1General...............................................................................................................6
2ACSI (Abstract Communication Service Interface) Conformance
Statement...........................................................................................................7
2.1 ACSI basic conformance statement................................................................. 7
2.2 ACSI models conformance statement ............................................................. 7
2.3 ACSI service conformance statement.............................................................. 8
3MICS - Model Implementation Conformance Statement..............................11
3.1 Model conformance ........................................................................................ 11
3.2 Common data attributes classes.................................................................... 11
Quality..............................................................................................................11
Analog value......................................................................................................11
Configuration of analogue value............................................................................11
Range configuration ............................................................................................11
Step position with transient indication....................................................................11
Pulse configuration..............................................................................................12
Originator..........................................................................................................12
Unit definition ....................................................................................................12
Vector...............................................................................................................12
Point definition ...................................................................................................12
CtlModels definition.............................................................................................12
SboClasses definition...........................................................................................12
3.3 Common data classes..................................................................................... 13
Single point status (SPS) .....................................................................................13
Double point status (DPS)....................................................................................13
Integer status (INS)............................................................................................13
Protection activation information (ACT)..................................................................13
Directional protection activation information (ACD)..................................................13
Security violation counting (SEC) ..........................................................................13
Binary counter reading (BCR) ...............................................................................13
Measured value (MV)...........................................................................................13
Complex measured value (CMV) ...........................................................................14
Sampled value (SAV) ..........................................................................................14
WYE..................................................................................................................14
Delta (DEL)........................................................................................................14
Sequence (SEQ) .................................................................................................14
Harmonic value (HMV).........................................................................................14
Harmonic value for WYE (HWYE)...........................................................................14
Harmonic value for DEL (HDEL) ............................................................................15
Controllable single point (SPC)..............................................................................15
Controllable double point (DPC) ............................................................................15
Controllable integer status (INC)...........................................................................16
Binary controlled step position information (BSC) .................................................... 16
Binary controlled step position information (ISC).....................................................16
Controllable analog set point information (APC).......................................................16
Single point setting (SPG)....................................................................................16
Integer status setting (ING) .................................................................................16
Analog setting (ASG)...........................................................................................16
Setting curve (CURVE) ........................................................................................16
Device name plate (DPL) .....................................................................................16
Logical node name plate (LPL)..............................................................................16
Curve shape description (CSD) .............................................................................17
3.4 Logical devices and logical nodes .................................................................. 17
3.4.1 System logical nodes..................................................................................17
Physical device information LPHD..........................................................................17

4
Logical node zero LLN0........................................................................................17
GOOSE subscription status CTRL/sbsLGOS1-sbsLGOS20...........................................17
3.4.2 Logical nodes for control.............................................................................18
Switch controllers CTRL/CSWI1- CSWI16 ...............................................................18
Switch control interlocking status CTRL/CILO1-CILO16.............................................18
Relay control interlocking status MET1/blkCILO1-blkCILO8........................................18
3.4.3 Logical nodes for switchgear........................................................................19
Circuit breakers CTRL/XCBR1- XCBR2....................................................................19
Circuit switches CTRL/XSWI1- XSWI14 ..................................................................19
3.4.4 Logical nodes for protection related functions ................................................19
Disturbance recorders MET1/drRDRE1-drRDRE8......................................................19
3.4.5 Logical nodes for generic reference ..............................................................20
External (GOOSE) indication status CTRL/extGGIO1.................................................20
Digital inputs MET1/biGGIO1-biGGIO8 ...................................................................20
Relay outputs MET1/boGGIO1-boGGIO8.................................................................20
Event flags MET1/evfGGIO1 – evfGGIO2 ................................................................21
Setpoint status MET1/spGGIO1- spGGIO2 ..............................................................21
Analog inputs MET1/aiGGIO1-aiGGIO2...................................................................21
3.4.6 Logical nodes for metering and measurement................................................22
Energy counters MET1/engMMTR1.........................................................................22
Harmonic demands MET1/demMHAI1 ....................................................................22
Sequence of harmonics MET1/hrmMHAI1 ...............................................................22
Total harmonics MET1/ocvMHAI1 ..........................................................................23
3-second total harmonics MET1/osvMHAI1 .............................................................23
Present demands MET1/demMMXU1 ......................................................................23
Sliding power demands MET1/demMMXU2..............................................................24
Accumulated power demands MET1/demMMXU3 .....................................................24
Predicted power demands MET1/demMMXU4 ..........................................................25
Half-cycle measurements MET1/hcvMMXU1 ............................................................25
One-second measurements MET1/osvMMXU1..........................................................25
Phasors MET1/phsrMMXU1 ...................................................................................26
Half-cycle sequence and imbalance MET1/hcvMSQI1................................................26
One-cycle imbalance MET1/ocvMSQI1....................................................................27
Sequence components MET1/seqMSQI1 .................................................................27
Minimum/maximum on any phase MET1/ocvMSTA1, MET1/osvMSTA1 ........................27
4PICS – Protocol Implementation Conformance Statement..........................29
4.1 Profile conformance........................................................................................ 29
A-Profile support.................................................................................................29
T-Profile support.................................................................................................29
4.2 MMS conformance .......................................................................................... 29
4.3 GOOSE conformance statement (GOOSE Services) ...................................... 31
4.4 GSSE conformance statement (GSSE Services) ............................................ 31
4.5 SCL services (SCL conformance) ................................................................... 31
5PIXIT - Protocol Implementation Extra Information for Testing..................32
5.1 Device configuration....................................................................................... 32
5.2 ACSI models.................................................................................................... 32
Association model...............................................................................................32
Server model .....................................................................................................32
Setting group model............................................................................................32
Dataset model....................................................................................................33
Reporting model.................................................................................................35
Control model ....................................................................................................39
GOOSE Publisher model.......................................................................................39
GOOSE Subscriber model.....................................................................................39
Time and time synchronization model ....................................................................39
File transfer model..............................................................................................40
5.3 Impact of the device settings......................................................................... 40
Logical device mode............................................................................................40

5
Controls ............................................................................................................40
Measurement units .............................................................................................40
Process Measurement Limits.................................................................................41
Deadbands ........................................................................................................41
Textual descriptions ............................................................................................ 41
6Configuring IEC 61850....................................................................................42
6.1 Licensing IEC 61850....................................................................................... 42
6.2 Configuring IED Properties ............................................................................ 42
6.3 Configuring Datasets...................................................................................... 43
6.4 Configuring Report Control Blocks................................................................. 45
6.5 Configuring the GOOSE Publisher .................................................................. 46
6.6 Configuring the GOOSE Subscriber................................................................ 46
6.7 Configuring Report Deadbands...................................................................... 50
6.8 Generating a CID File...................................................................................... 51

6
1 General
The PM180 is provided with an embedded IEC 61850 server compliant with the IEC 61850
set of standards.
This document contains the IEC 61850 conformance statements that give the summary of
the device data object model, protocol implementations and communication capabilities of
the PM180.
For detailed information on operating the PM180 and communication settings refer to the
PM180 Operation Manual.
IMPORTANT
Control commands addressed to the CSWI switch controller nodes and to the boGGIO
general binary output nodes will be rejected until the internal BOOLEAN variable
REMOTE MODE is set to TRUE via a setpoint logic equation. See Controls in Section 5.3
for details.

7
2 ACSI (Abstract Communication Service
Interface) Conformance Statement
This chapter contains the ACSI conformance statement as defined in Annex A of IEC 61850-
7-2 that specifies the device communication features mapped to an SCSM (Specific
Communication Service Mapping).
2.1 ACSI basic conformance statement
Services Client/
Subscriber Server/ Publisher Value/ Comments
Client-server roles
B11 Server side (of TWO-PARTY-APPLICATION-
ASSOCIATION) zc1
B12 Client side of (TWO-PARTY-APPLICATION-
ASSOCIATION)
SCSMs supported
B21 SCSM: IEC 61850-8-1 used z
B22 SCSM: IEC 61850-9-1 used
B23 SCSM: IEC 61850-9-2 used
B24 SCSM: other
Generic substation event model (GSE)
B31 Publisher side z
B32 Subscriber side z
Transmission of sampled value model (SVC)
B41 Publisher side
B42 Subscriber side
c1– declared support for LOGICAL-DEVICE model
z– supported
2.2 ACSI models conformance statement
Services Client/
Subscriber Server/ Publisher Value/ Comments
If Server side (B11) supported
M1 Logical device zc2
M2 Logical node zc3
M3 Data zc4
M4 Data set zc5
M5 Substitution z
M6 Setting group control
Reporting
M7 Buffered report control z
M7-1 sequence-number z
M7-2 report-time-stamp z
M7-3 reason-for-inclusion z
M7-4 data-set-name z
M7-5 data-reference z
M7-6 buffer-overflow z
M7-7 entryID z
M7-8 BufTm z
M7-9 IntgPd z
M7-10 GI z
M8 Unbuffered report control z
M8-1 sequence-number z
M8-2 report-time-stamp z
M8-3 reason-for-inclusion z
M8-4 data-set-name z

8
Services Client/
Subscriber Server/ Publisher Value/ Comments
M8-5 data-reference z
M8-6 BufTm z
M8-7 IntgPd z
M8-8 GI z
Logging
M9 Log control
M9-1 IntgPd
M10 Log
M11 Control z
If GSE (B31/B32) is supported
GOOSE
M12-1 entryID
M12-2 DataRefInc
M13 GSSE
If SVC (B41/B42) is supported
M14 Multicast SVC
M15 Unicast SVC
M16 Time
zTime source with required accuracy shall be available
M17 File Transfer z
c2 – declared support for LOGICAL-NODE model
c3 – declared support for DATA model
c4 – declared support for DATA-SET, Report, or Time model
c5 – declared support for Report model
z– supported
2.3 ACSI service conformance statement
AA – APPLICATION-ASSOCIATION; TP – TWO- PARTY; MC – Multicast
Services AA:
TP/MC Client/ Subscriber Server/ Publisher Comments
Server (Clause 6)
S1 ServerDirectory TP z
Application association (Clause 7)
S2 Associate z
S3 Abort z
S4 Release z
Logical device (Clause 8)
S5 LogicalDeviceDirectory TP z
Logical node (Clause 9)
S6 LogicalNodeDirectory TP z
S7 GetAllDataValues TP z
Data (Clause 10)
S8 GetDataValues TP z
S9 SetDataValues TP
S10 GetDataDirectory TP z
S11 GetDataDefinition TP z
Data set (Clause 11)
S12 GetDataSetValues TP z
S13 SetDataSetValues TP z
S14 CreateDataSet TP z
S15 DeleteDataSet TP z
S16 GetDataSetDirectory TP z
Substitution (Clause 12)
S17 SetDataValues TP zApplied to

9
Services AA:
TP/MC Client/ Subscriber Server/ Publisher Comments
Setting group control (Clause 13)
S18 SelectActiveSG TP
S19 SelectEditSG TP
S20 SetSGValues TP
S21 ConfirmEditSGValues TP
S22 GetSGValues TP
S23 GetSGCBValues TP
Reporting (Clause 14)
Buffered report control block (BRCB)
S24 Report TP z
S24-1 data-change (dchg) z
S24-2 qchg-change (qchg) z
S24-3 data-update (dupd) z
S25 GetBRCBValues TP z
S26 SetBRCBValues TP z
Unbuffered report control block (URCB)
S27 Report TP z
S27-1 data-change (dchg) z
S27-2 qchg-change (qchg) z
S27-3 data-update (dupd) z
S28 GetURCBValues TP z
S29 SetURCBValues TP z
Logging (Clause 14)
Log control block
S30 GetLCBValues TP
S31 SetLCBValues TP
Log
S32 QueryLogByTime TP
S33 QueryLogAfter TP
S34 GetLogStatusValues TP
Generic substation event model (GSE) (Clause 15)
GOOSE-CONTROL-BLOCK
S35 SendGOOSEMessage MC z
S36 GetGoReference TP
S37 GetGOOSEElementNumber TP
S38 GetGoCBValues TP z
S39 SetGoCBValues TP z
GSSE-CONTROL-BLOCK
S40 SendGSSEMessage MC
S41 GetGsReference TP
S42 GetGSSEElementNumber TP
S43 GetGsCBValues TP
S44 SetGsCBValues TP
Transmission of sampled value model (SVC) (Clause 16)
Multicast SVC
S45 SendMSVMessage MC
S46 GetMSVCBValues TP
S47 SetMSVCBValues TP
Unicast SVC
S48 SendUSVMessage TP
S49 GetUSVCBValues TP
S50 SetUSVCBValues TP
Control (Clause 17)
S51 Select TP zFor boGGIO class nodes
S52 SelectWithValue TP
S53 Cancel TP zFor boGGIO class nodes

10
Services AA:
TP/MC Client/ Subscriber Server/ Publisher Comments
S54 Operate TP z
S55 Command-Termination TP zFor CSWI class nodes
S56 TimeActivated-Operate TP
File transfer (Clause 20)
S57 GetFile TP z
S58 SetFile TP
S59 DeleteFile TP
S60 GetFileAttributeValues TP z
Time (Clause 18)
T1 Time resolution of internal clock
(nearest value of 2**-n in seconds) n=10 (T1)
T2 Time accuracy of internal clock n=10 (T1)
T3 Supported TimeStamp resolution
(nearest value of 2**-n in seconds) n=10 (T1)
z– supported

11
3 MICS - Model Implementation Conformance
Statement
This chapter contains the MICS conformance statement as required by IEC 61850-10. It lists
data object model elements supported by the PM180 and provides definitions of the logical
nodes, common data classes and data attribute types as defined in IEC 61850-7-3 and IEC
61850-7-4.
3.1 Model conformance
The model conformance of the PM180 is described by its ICD file.
3.2 Common data attributes classes
The following tables indicate which fields are supported in each Common Data Attribute
Class. Not listed fields are either optional (O) or conditional (C) and are not supported by the
PM180. Mandatory fields (M) are always present.
Quality
Attribute name Attribute type Value/Range M/O/C Comments
validity CODED ENUM good | invalid M Supported
detailQual PACKED LIST M Supported
overflow BOOLEAN FALSE M Defaulted
outOfRange BOOLEAN TRUE | FALSE M Supported
badReference BOOLEAN TRUE | FALSE M Supported
oscillatory BOOLEAN FALSE M Defaulted
failure BOOLEAN TRUE | FALSE M Supported
oldData BOOLEAN FALSE M Defaulted
inconsistent BOOLEAN FALSE M Defaulted
inaccurate BOOLEAN FALSE M Defaulted
source CODED ENUM process M Defaulted
test BOOLEAN FALSE M Defaulted
operatorBlocked BOOLEAN FALSE M Defaulted
Analog value
Attribute name Attribute type Value/Range M/O/C Comments
i INT32 integer value C
f FLOAT32 floating point value C
Only one of the attributes may be present for a given instance of DATA.
Configuration of analogue value
Common data attribute class is not supported.
Range configuration
Common data attribute class is not supported.
Step position with transient indication
Common data attribute class is not supported.

12
Pulse configuration
Attribute Name Attribute Type Value/Range M/O/C Comments
cmdQual ENUMERATED pulse | persistent MFor boGGIO pulse output,
a relay must be set to
pulse mode via the device
Relay Setup
onDur INT32U MboGGIO class nodes:
default = 2000 ms
CSWI class nodes:
default = 0
offDur INT32U MNot supported
numPls INT32U 1 M Read only
Originator
Attribute Name Attribute Type Value/Range M/O/C Comments
orCat ENUMERATED not-supported | bay-control |
station-control | remote-control
| automatic-bay | automatic-
station | automatic-remote |
maintenance | process
M
orIdent OCTET STRING64 M
Unit definition
Attribute Name Attribute Type Value/Range M/O/C Comments
SIUnit ENUMERATED See IEC61850-7-3, Tables A.1
to A.4 in Annex A M
multiplier ENUMERATED See IEC61850-7-3, Table A.5 in
Annex A O
The default value of the multiplier is 0 and the multiplier value is 1: 10**0 = 1.
Vector
Attribute Name Attribute Type Value/Range M/O/C Comments
mag AnalogueValue M Only one of the attributes
of the AnalogueValue may
be present for a given
instance of DATA.
ang AnalogueValue O ang attribute is used for
data objects of the
phzrMMXU LN only (see
below)
Point definition
Common data attribute class is not supported.
CtlModels definition
Attribute Value Comments
status-only Not controllable SPS, DPS and INS
direct-with-normal-security Controllable SPC. Supported by boGGIO and evfGGIO class nodes.
sbo-with-normal-security Controllable SPC. Supported by boGGIO and evfGGIO class nodes.
direct-with-enhanced-security Controllable DPC. Supported by CSWI class nodes.
sbo-with-enhanced-security Not supported
SboClasses definition
Attribute Value Comments
operate-once
operate-many Not supported

13
3.3 Common data classes
The following tables indicate mandatory, conditional and optional attributes of each Common
Data Class (CDC) that are supported by the PM180. Mandatory attributes (M) are always
present.
Single point status (SPS)
Attribute Name Attribute Type FC M/O/C Comments
stVal BOOLEAN ST M
q Quality ST M
t TimeStamp ST M
d VISIBLE STRING64 DC O
subEna BOOLEAN SV PICS_SUBST
Supported by CTRL/CILO nodes1
subVal CODED ENUM SV PICS_SUBST
Supported by CTRL/CILO nodes1
subQ Quality SV PICS_SUBST Supported by CTRL/CILO nodes
1Indicate the switch interlocking bypass status for EnaCls and EnaOpn attributes in CTRL/CILO
nodes: TRUE when interlocking bypass is enabled, FALSE when bypass is disabled.
Double point status (DPS)
Attribute Name Attribute Type FC M/O/C Comments
stVal CODED ENUM ST M
q Quality ST M
t TimeStamp ST M
Integer status (INS)
Attribute Name Attribute Type FC M/O/C Comments
stVal INT32 ST M
q Quality ST M
t TimeStamp ST M
d VISIBLE STRING64 DC O
Protection activation information (ACT)
Common data class is not supported.
Directional protection activation information (ACD)
Common data class is not supported.
Security violation counting (SEC)
Common data class is not supported.
Binary counter reading (BCR)
Attribute Name Attribute Type FC M/O/C Comments
actVal INT32 ST M
q Quality ST M
t TimeStamp ST M
units Unit CF O
pulsQty FLOAT32 CF M
d VISIBLE STRING64 DC O
Measured value (MV)
Attribute Name Attribute Type FC M/O/C Comments
mag AnalogueValue MX M Onl
y
one of the attributes
(
i or f
)
of

14
Attribute Name Attribute Type FC M/O/C Comments
the AnalogueValue may be present
for a given instance of DATA
q Quality MX M
t TimeStamp MX M
units Unit CF O
db INT32U CF O
d VISIBLE STRING64 DC O
Complex measured value (CMV)
Attribute Name Attribute Type FC M/O/C Comments
cVal Vector MX M
q Quality MX M
t TimeStamp MX M
units Unit CF O
db INT32U CF O
d VISIBLE STRING64 DC O
Sampled value (SAV)
Common data class is not supported.
WYE
Attribute Name Attribute Type FC M/O/C Comments
phsA CMV C
phsB CMV C
phsC CMV C
neut CMV C Signed with (*) where available
Delta (DEL)
Attribute Name Attribute Type FC M/O/C Comments
phsAB CMV C
phsBC CMV C
phsCA CMV C
Sequence (SEQ)
Attribute Name Attribute Type FC M/O/C Comments
c1 CMV M
c2 CMV M
c3 CMV M
seqT ENUMERATED MX M pos-neg-zero | dir-quad-zero
Harmonic value (HMV)
Common data class is not supported.
Harmonic value for WYE (HWYE)
Attribute Name Attribute Type FC M/O/C Comments
q Quality MX M
t TimeStamp MX M
phsAHar ARRAY[0..numHar] OF
Vector MX M
phsBHar ARRAY[0..numHar] OF
Vector MX O
phsCHar ARRAY[0..numHar] OF
Vector MX O
numHar INT16U CF M numHar = 63 (no subharmonics)

15
Attribute Name Attribute Type FC M/O/C Comments
numCyc INT16U CF M numCyc = 1
units Unit CF O
evalTm INT16U CF M evalTm = nominal period
frequency FLOAT32 CF M frequency = nominal frequency
d VISIBLE STRING64 DC O
Harmonic value for DEL (HDEL)
Attribute Name Attribute Type FC M/O/C Comments
q Quality MX M
t TimeStamp MX M
phsABHar ARRAY[0..numHar] OF
Vector MX M
phsBCHar ARRAY[0..numHar] OF
Vector MX O
phsCAHar ARRAY[0..numHar] OF
Vector MX O
numHar INT16U CF M numHar = 63 (no subharmonics)
numCyc INT16U CF M numCyc = 1
units Unit CF O
evalTm INT16U CF M evalTm = nominal period
frequency FLOAT32 CF M frequency = nominal frequency
d VISIBLE STRING64 DC O
Controllable single point (SPC)
Applied to boGGIO and evfGGIO class nodes.
Attribute Name Attribute Type FC M/O/C Comments
ctlVal BOOLEAN CO C See notes below for relay operation
explanation
stVal BOOLEAN ST M
q Quality ST M
t TimeStamp ST M
d VISIBLE STRING64 DC O
pulseConfig PulseConfig CF O
ctlModel CtlModels CF M
Relay output operation depends on the configurable cmdQual attribute value (see
pulseConfig) and the relay operation mode configured in the device via the Relay Setup as
described in the following table.
cmdQual Relay operation
mode Relay output operation
pulse Pulse/KYZ Pulse output. ctlVal = 1 – generates a pulse (normal/KYZ) with a duration
defined by the onDur attribute; ctlVal = 0 – no effect
pulse Latched/unlatched No effect
persistent Pulse/KYZ Pulse output. ctlVal = 1 – generates a pulse (normal/KYZ) with a duration
defined by the pulse width pre-configured in the device setup; ctlVal = 0 – no
effect
persistent Latched/unlatched Latched output. ctlVal = 1 – switch on, ctlVal = 0 – switch off
Controllable double point (DPC)
Applied to CSWI class nodes.
Attribute Name Attribute Type FC M/O/C Comments
ctlVal BOOLEAN CO C
stVal CODED ENUM ST M
q Quality ST M
t TimeStamp ST M
subEna BOOLEAN SV PICS_SUBST

16
subVal CODED ENUM SV PICS_SUBST
subQ Quality SV PICS_SUBST
pulseConfig PulseConfig CF O
ctlModel CtlModels CF M
d VISIBLE STRING64 DC O
Controllable integer status (INC)
Attribute Name Attribute Type FC M/O/C Comments
ctlVal INT32 CO C
stVal INT32 ST M
q Quality ST M
t TimeStamp ST M
d VISIBLE STRING64 DC O
Binary controlled step position information (BSC)
Common data class is not supported.
Binary controlled step position information (ISC)
Common data class is not supported.
Controllable analog set point information (APC)
Common data class is not supported.
Single point setting (SPG)
Common data class is not supported.
Integer status setting (ING)
Common data class is not supported.
Analog setting (ASG)
Common data class is not supported.
Setting curve (CURVE)
Common data class is not supported.
Device name plate (DPL)
Attribute Name Attribute Type FC M/O/C Comments
vendor VISIBLE STRING255 DC M
model VISIBLE STRING255 DC O
location VISIBLE STRING255 DC O
Logical node name plate (LPL)
Attribute Name Attribute Type FC M/O/C Comments
vendor VISIBLE STRING255 DC M
swRev VISIBLE STRING255 DC M
d VISIBLE STRING255 DC M
confgRev VISIBLE STRING255 DC C LLN0 only
ldNs VISIBLE STRING255 DC C LLN0 only

17
Curve shape description (CSD)
Common data class is not supported.
3.4 Logical devices and logical nodes
The PM180 IEC 61850 server provides a single logical device MET1.
The PM180 IEC 61850 server provides two logical devices CTRL and MET1 described in the
following table. The domain name of a logical device can incorporate a configurable IED
name (see Section 6.2) that will precede a logical device name.
Logical device Description
CTRL Bay control elements – breaker and switch control
MET1 Metering, measurements and general digital input and output
elements
Logical devices contain logical nodes LPHD and LLN0 dedicated to the PM180 unit, and a set
of functional logical nodes for functions supported by the PM180. Logical node names are
fixed.
The following tables describe attributes of logical nodes. Not listed attributes are either
optional (O), or conditional (C) and are not supported by the PM180. Mandatory (M)
attributes are always present.
The PM180 also uses extension (E) attributes for some logical nodes.
3.4.1 System logical nodes
Physical device information LPHD
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
LNName Object name LPHD1 M
PhyNam DPL Physical device name plate M
PhyHealth INS Physical device health M
Proxy SPS Indicates if this LN is a proxy M Defaulted to FALSE
Logical node zero LLN0
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
LNName Object name LLN0 M
Common Logical Node Information
Mod INC Mode M
Beh INS Behavior M
Health INS Health M
NamePlt LPL Name plate M
GOOSE subscription status CTRL/sbsLGOS1-sbsLGOS20
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
LNName Object name sbsLGOS1…sbsGOS20 M
Common Logical Node Information
Mod INC Mode M
Beh INS Behavior M
Health INS Health M
NamePlt LPL Name plate M
Status Information
SbsSt SPS Status of the subscription M TRUE = active
FALSE = not active
LastStNum INS Last state number received O
ConfRevNum INS Ex
p
ected confi
g
uration revision O

18
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
number
3.4.2 Logical nodes for control
Switch controllers CTRL/CSWI1- CSWI16
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
LNName Object name CSWI1…CSWI16 M A configurable prefix can be
added to a LNName via the
device Bay Control Setup
Common Logical Node Information
Mod INC Mode M
Beh INS Behavior M
Health INS Health M
NamePlt LPL Name plate M
Status Information
Loc SPS Local control behavior O
Controls
Pos DPC Switch, general M
Switch control interlocking status CTRL/CILO1-CILO16
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
LNName Object
name CILO1…CILO16 M A configurable prefix can be added to a
LNName via the device
Bay Control Setup
Common Logical Node Information
Mod INC Mode M
Beh INS Behavior M
Health INS Health M
NamePlt LPL Name plate M
Status Information
EnaOpn SPS Enable Open M
EnaCls SPS Enable Close M
Relay control interlocking status MET1/blkCILO1-blkCILO8
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
LNName Object
name blkCILO1…blkCILO8 M
Common Logical Node Information
Mod INC Mode M
Beh INS Behavior M
Health INS Health M
NamePlt LPL Name plate M
Status Information
EnaOpn1…EnaOpn8 SPS Enable Open:
Relay outputs RO1-RO8 (blkCILO1)
Relay outputs RO9-RO16 (blkCILO2)
Relay outputs RO17-RO24 (blkCILO3)
Relay outputs RO25-RO32 (blkCILO4)
Relay outputs RO33-RO40 (blkCILO5)
Relay outputs RO41-RO48 (blkCILO6)
Relay outputs RO49-RO56 (blkCILO7)
Relay outputs RO57-RO64 (blkCILO8)
M Blocking operation is
configurable via the
Relay setup. A relay can
only be unblocked via a
control setpoint.
EnaCls1…EnaCls8 SPS Enable Close:
Relay outputs RO1-RO8 (blkCILO1) M Blocking operation is confi
g
urable via the

19
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
Relay outputs RO9-RO16 (blkCILO2)
Relay outputs RO17-RO24 (blkCILO3)
Relay outputs RO25-RO32 (blkCILO4)
Relay outputs RO33-RO40 (blkCILO5)
Relay outputs RO41-RO48 (blkCILO6)
Relay outputs RO49-RO56 (blkCILO7)
Relay outputs RO57-RO64 (blkCILO8)
Relay setup. A relay can
only be unblocked via a
control setpoint.
3.4.3 Logical nodes for switchgear
Circuit breakers CTRL/XCBR1- XCBR2
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
LNName Object name XCBR1…XCBR2 M A configurable prefix can be
added to a LNName via the
device Bay Control Setup
Common Logical Node Information
Mod INC Mode M
Beh INS Behavior M
Health INS Health M
NamePlt LPL Name plate M
Status Information
Loc SPS Local control behavior M
OpCnt INS Operation counter M
AlmFlt SPS Breaker fault trip alarm E
Controls
Pos DPC Switch position M ST only
BlkOpn SPC Block opening M ST only
BlkCls SPC Block closing M ST only
Circuit switches CTRL/XSWI1- XSWI14
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
LNName Object name XSWI1…XSWI14 M A configurable prefix can be
added to a LNName via the
device Bay Control Setup
Common Logical Node Information
Mod INC Mode M
Beh INS Behavior M
Health INS Health M
NamePlt LPL Name plate M
Status Information
Loc SPS Local control behavior M
OpCnt INS Operation counter M
SwTyp INS Switch type M
Controls
Pos DPC Switch position M ST only
BlkOpn SPC Block opening M ST only
BlkCls SPC Block closing M ST only
3.4.4 Logical nodes for protection related functions
Disturbance recorders MET1/drRDRE1-drRDRE8
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
LNName Object name drRDRE1…drRDRE8 M
Common Logical Node Information

20
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
Mod INC Mode M
Beh INS Behavior M
Health INS Health M
NamePlt LPL Name plate M
Status Information
RcdMade SPS Recording made M Set to TRUE when at least
one disturbance waveform
is available for a read.
FltNum INS Fault number M Indicates the last waveform
series number available in a
disturbance recorder.
3.4.5 Logical nodes for generic reference
External (GOOSE) indication status CTRL/extGGIO1
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
LNName Object name extGGIO1 M
Common Logical Node Information
Mod INC Mode M
Beh INS Behavior M
Health INS Health M
NamePlt LPL Name plate M
Status Information
Ind1…Ind128 SPS General indication O
Digital inputs MET1/biGGIO1-biGGIO8
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
LNName Object name biGGIO1…biGGIO8 M
Common Logical Node Information
Mod INC Mode M
Beh INS Behavior M
Health INS Health M
NamePlt LPL Name plate M
Status Information
Ind1…Ind16 SPS General indication:
Digital inputs DI1-DI16 (biGGIO1)
Digital inputs DI17-DI33 (biGGIO2)
Digital inputs DI34-DI48 (biGGIO3)
Digital inputs DI49-DI64 (biGGIO4)
Digital inputs DI65-DI80 (biGGIO5)
Digital inputs DI81-DI96 (biGGIO6)
Digital inputs DI97-DI112 (biGGIO5)
Digital inputs DI113-DI128
(biGGIO6)
O TRUE = closed
FALSE = open
Relay outputs MET1/boGGIO1-boGGIO8
Attribute name Attribute
type Explanation/Value T M/O/C/E Comments
LNName Object
name boGGIO1…boGGIO8 M
Common Logical Node Information
Mod INC Mode M
Beh INS Behavior M
Health INS Health M
NamePlt LPL Name plate M