Satec PM130 PLUS User manual

PM130 PLUS Quickstart
QuickStart Guide
PM130PLUS
Series
Powermeters
BG0441 REV.A7
BCS Switchgear Inc.
Switchgear | Circuit Breakers | Parts | Tech Support
bcsswitchgear.com | 888.599.0486
Need Help? 888.599.0486

PM130 PLUS Quickstart
2
Mechanical Installation
Figure 1: Instrument Dimensions
BCS Switchgear Inc.
Switchgear | Circuit Breakers | Parts | Tech Support
bcsswitchgear.com | 888.599.0486
Need Help? 888.599.0486

PM130 PLUS Quickstart
3
Figure 2: Mounting the PM130 PLUS (Square or Round cut-out)
IMPORTANT!
Only qualified personnel can perform setup.
All incoming power sources must be turned off during installation. During operation of the
Powermeter, hazardous voltages are present on the input terminals. Failure to observe
precautions can result in serious or even fatal injury, or damage to equipment.
Please refer to the installation and operation manual for further information.
BCS Switchgear Inc.
Switchgear | Circuit Breakers | Parts | Tech Support
bcsswitchgear.com | 888.599.0486
Need Help? 888.599.0486

PM130 PLUS Quickstart
4
NOTE:
Refer to the Installation
and operation manual
for the wiring
schematics diagrams
Typical Electrical Installation
Figure 3: Common Wiring Mode: 4LL3 or 4L-n3
Wiring Configuration Setup Code
3-wire 2-element Direct connection using 2 CTs 3dir2
4-wire Wye 3-element direct connection using 3 CTs 4Ln3 or 4LL3
4-wire Wye 3-element connection using 3 PTs, 3 CTs 4Ln3 or 4LL3
3-wire 2-element Open Delta connection using 2 PTs, 2 CTs 3OP2
4-wire Wye 2½ -element connection using 2 PTs, 3 CTs 3Ln3 or 3LL3
3-wire 2½ -element Open Delta connection using 2 PTs, 3 CTs 3OP3
4-wire 3-element Delta direct connection using 3 CTs 4Ln3 or 4LL3
3-wire 2½-element Broken Delta connection using 2 PTs, 3 CTs 3bLn3 or 3bLL3

PM130 PLUS Quickstart
5
Figure 4: CT Wiring
MODULE Installation
This section applies to the I/O and Communication modules.
Figure 5: PM130 PLUS modules
MODULE
4 ANALOG OUT
MODULE
ETHERNET
MODULE
4DI/2DO

PM130 PLUS Quickstart
6
Figure 6: Mounting module
CAUTION!
Before I/O Module installation ensure that all incoming power sources are shut OFF.
Failure to observe this practice can result in serious or even fatal injury and damage
to equipment.
NOTE:
Refer to the Installation
and operation manual
for the wiring
schematics dia
g
rams
Module
Connector

PM130 PLUS Quickstart
7
Basic Setup
All setups can be performed directly from the display panel or via communication ports
using PAS communication software, except for Communications and Display setups,
which must be performed directly at the instrument panel.
To set the CT Primary current, perform the following steps:
•Press
•Press ▲+
↓
•Press : "5" should blink.
•Use the ▲▼ arrows to scroll to the desired value
(Press ▲▼ continuously for quick scrolling).
•Press to save the selected value.
•Press (X3) to return to the display menu.
Performing Basic and Communications Setup
•Press (X3) .
•Press ▲▼ to scroll to desired menu.
•Press to activate middle window.
•Press ▲▼ to scroll to desired option.
•Press to activate lower window.
•Press ▲▼ to scroll to desired value.
•Press to save selected value.
•Press (X3) to return to the display menu.
ESC
SELECT
ENTER
ENTER
ENTER SELECT
ESC
ENTER
SELECT
SELECT
SELECT
ÎÎbASc
4L/n3
ConF
Prt.1
ASCII
Prot
menu
option
value
menu
option
value
bASc
5
Ct
menu
option
value
CH
G
STA
CHG
OPS
menu
option
value
Small LEDs indicate
measured parameter
Load bar graph, indicates
% nominal load current

PM130 PLUS Quickstart
8
DATA DISPLAY
Navigating in Display Mode
The front panel has a simple interface that allows you to display numerous measurement
parameters in up to 38 display pages. For easier reading, the parameters are divided
into three groups, each accessible by a designated key. These are:
yCommon measurements - no selection key
yMin/Max measurements - selected by the key
yEnergy measurements - selected by the key
The up/down arrow keys are used as follows in Display Mode:
▼Scrolls through the pages downward (forward)
▲Scrolls through the pages upward (backward)
▲▼Returns to the first page within current measurement group
For each display page, up to three parameters can be displayed. The Load bar graph
displays the percentage of the highest of 3 phases current measured by the PM130
PLUS.
Selecting a Display Page
•Press the ▲▼ to scroll through display pages.
Selecting Common Measurements
•Press the key pointed to by the illuminated round LED below the front panel display.
If no LED is lit up, the front panel is currently displaying the common measurements
parameters.
Selecting Min/Max Measurements
•Press the key. Use the ▲▼ to scroll through Min/Max and Max. demand
measurements.
Selecting Energy Measurements
•Press the key. Use the ▲▼ to scroll through the different energy readings.
MAX
/
MIN
MAX/MIN
ENER
GY
ENERG
Y

PM130 PLUS Quickstart
9
Basic Menu
Code Parameter Options Description
ConF Wiring mode 3OP2 3-wire open delta using 2 CTs
4Ln3 4-wire Wye using 3 PTs (default)
3dir2 3-wire direct connection using 2 CTs
4LL3 4-wire Wye using 3 PTs
3OP3 3-wire open delta using 3 CTs
3Ln3 4-wire Wye using 2 PTs
3LL3 4-wire Wye using 2 PTs
3bLn3 3-wire Broken delta using 2 PTs, 3 CTs
3bLL3 3-wire Broken delta using 2 PTs, 3 CTs
Pt PT ratio 1.0∗- 6,500.0 The potential transformer ratio
Ct CT primary current 1-50,000A (5*) The primary rating of the current transformer
d.P PM130E PLUS,
PM130EH PLUS
Power demand period 1, 2, 5, 10, 15*, 20,
30, 60, E The length of the period for power demand calculations, in minutes. E = external synchronization
n.dp PM130E PLUS
PM130EH PLUS
Number of power
demand periods 1-15 (1*)
The number of demand periods to be averaged for sliding window
demands
1 = block interval demand calculation
A.dP
Ampere/Volt demand
period 0-1800 (900*) The length of the period for volt/ampere demand calculations, in seconds. 0 = measuring peak current
Freq Nominal frequency 25, 50, 60, 400 (Hz) The nominal power utility frequency
•- Default setup
Communication Port Menu
COM1 setting
Code Parameter Options Description
Prot Communications protocol ASCII∗, rtu, dnP3 ASCII, Modbus RTU (default) or DNP3.0 protocol
rS Interface standard 485 RS-485 interface (default)
Addr Address ASCII: 0 (default) - 99 , Modbus: 1 (default) -247 , DNP3.0: 0 (default) -255
bAud Baud rate 110, 300, 600, 1200, 2400, 4800, 9600 (default), up to 115,200 bps
dAtA Data format 7E, 8E (7/8 bits, even parity), 8n (default) (8 bits, no parity)
COM2 setting (optional communication module)
Code Parameter Options Description
Prot Communications protocol rtu, dnP3, PrFB Modbus/TCP or DNP3/TCP or Profibus DP protocol
rS Interface standard Eth., PrFB Ethernet interface (default) or Profibus DP
Addr Address Modbus: 1 (default) -247 , DNP3.0: 0-65532 , Profibus DP: 0-126

PM130 PLUS Quickstart
10
Input and Output Ratings
DIRECT INPUT - Nominal: 690V line-to-line voltage, 790V maximum; 400V
line-to-neutral, 460V maximum - Burden: <0.5 VA. INPUT USING PT -
Burden: <0.15 VA
690 V: (standard)
INPUT USING PT - Nominal: 120V line-to-line voltage, 144V maximum -
Burden: <0.1 VA
120 V: (optional)
Maximum wire section: 4 mm2 (10 AWG) Voltage input terminals
3 voltage inputs
INPUT VIA CT with 5A secondary output - Burden: 2.5 to 4 mm2 (13-11
AWG) wire from CT Overload withstand: 15A RMS continuous, 300A RMS
for 1 second.
5A: (standard)
INPUT VIA CT with 1A secondary output - Burden: 2.5 to 4 mm2 (13-11
AWG) wire from CT Overload withstand: 3A RMS continuous, 80A RMS for
1 second.
1A:(optional)
3 current inputs
(Galvanically
isolated
)
Optically isolated, max. speed 115.2Kb/s EIA RS-485 standard
3 x Maximum wire section: 2.5 mm2 (12 AWG) COM1 terminals
Communication port
COM1
85-265VAC, 88-290VDC; 50/60/400 Hz 9VA
120/230 V AC/DC
(standard)
9.5-18VDC 12 VDC (optional)
18.5-72VDC 24/48 VDC (optional)
3 x Maximum wire section: 2.5 to 4 mm2 (13-11 AWG)
Power Supply input
terminals
Power Supply
(Galvanically
isolated)
Dry contact, internally wetted @ 24VDC
DIGITAL INPUTS x 4
optically isolated inputs
5A/250 VAC; 5A/30 VDC, 1 contact (SPST Form A) RELAY x 2
0.15A/250 VAC - 400 VDC, 1 contact (SPST Form A) SSR x 2
DIGITAL
OUTPUTS
9 x Maximum wire section: 2.5 mm2 (12 AWG) 4DI/2DO terminals
MODULE 4DI/2DO
(Optional)
±1 mA, maximum load 5 kΩ(100% overload)
0-20 mA, maximum load 510 Ω
4-20 mA, maximum load 510 Ω
0-1 mA, maximum load 5 k Ω(100% overload)
ANALOG OUT x 4 optically
isolated outputs
(4 different options)
5 x Maximum wire section: 2.5 mm2 (12 AWG) 4 AO terminals
MODULE 4 AO
(Optional)
10/100 Base T, auto adaptation speed, Max. speed 100Mb/s Ethernet
Shielded RJ45 cable ETH connector
Communication port
COM2
(Optional)
Max. speed 12 Mb/s Profibus
5 x Maximum wire section: 2.5 mm2 (12 AWG) or using terminal to DB9
converter: P/N AC0153 REV.A2
Profibus terminals
Communication port
COM2
(Optional)