SATO s84ex User manual

First edition: Jan 2015
Q04652900
©2015 SATO CORPORATION
This recommendation has been tested successfully at SATO. Results may vary in the actual
customer installation due to overall system tolerances. Validation of functionality in the actual
system is therefore recommended.
In no event shall SATO be liable for any faults arising out of use of or inability to use the product.
UHF Inlay Configuration Guide
Printer Orientation and Label Measurements
X1:Liner edge to center of chip for Orientation X2:Liner edge to center of chip for Orientation
Y: Optimum Encoding Position*
S: Minimum Inlay Separation
*Y: Measured from tail edge of I-mark to lead edge of inlay when I-mark sensor is used.
Measured from lead edge of label to lead edge of inlay when gap sensor is used.
How to check the Configuration Table
S84-ex UHF Inlay Placement & Configuration Table
In order to successfully configure your S84-ex UHF printer,
you will need the following information about your label.
Media feed direction
I-Mark
X1
Media feed direction
X2
I-Mark
$PHULFDV6WDQGDUG5LJKW+DQG
(XURSH$VLD/HIW+DQG
$PHULFDV2SSRVLWH/HIW+DQG
(XURSH$VLD5LJKW+DQG
Position(mm)
Power (dBm) Position(mm) Power (dBm)
NO. Manufacturer
Inlay
[IC Chip] Feed Direction
Region
Antenna
Pitch X Y S Write Read X Y S Write Read
1Alien
7HFKQRORJ\
$/1³6TXLJJOH´
>$OLHQ+LJJV@
Short Pitch 50.7-55.4 1-5 19 22 9     
Standard          
Short Pitch 50.4-55.4 2-6 19 22 9 60.4-65.4 1-7 19 24 12
Standard          
2Alien
7HFKQRORJ\
$/1³6KRUW´
>$OLHQ+LJJV@
Short Pitch ² ² ² ² ²     
Standard  
Short Pitch          
Standard  
Alien
7HFKQRORJ\
$/1³6KRUW´
>$OLHQ+LJJV@
Short Pitch          
Standard          
Short Pitch          
Standard          
Feed Direction
The arrow in the header of table
indicates the direction in which labels
are output from the printer.
3ODFHPHQWDQG&RQILJXUDWLRQVYDOLG
IRU(XURSHDQ(76,IUHTXHQF\
UDQJH0+]
9DOLGIRU)UHTXHQFLHVWKDWIDOOZLWKLQ
WKH)&&UDQJH0+]
Feed direction affects results, and
is signified by the images in the
following table.
Select the related
Antenna Pitch according
to your label’s “Y” value.
Printer orientation will
affect viable settings.

For inlays not included on this list, please contact your local SATO dealer or sales office.
www.satoworldwide.com
• Squiggle and Higgs are trademarks or registered trademarks of Alien Technology Corporation in the U.S. and other countries.
• Monza is registered trademark of Impinj, Inc.
Americas: Standard/Right Hand
Europe/Asia: Left Hand
Americas: Opposite/Left Hand
Europe/Asia: Right Hand
Position(mm)
Power (dBm) Position(mm) Power (dBm)
NO. Manufacturer
Inlay
[IC Chip] Feed Direction
Region
Antenna
Pitch X Y S Write Read X Y S Write Read
1Alien
Technology
ALN-9640 “Squiggle”
[Alien Higgs3]
Short Pitch 50.7-55.4 1-5 19 22 9 — — — — —
Standard 55.4-70.4 2-16 54 22 13 50.4-60.4 17-24 30 20 7
Short Pitch 50.4-55.4 2-6 19 22 9 60.4-65.4 1-7 19 24 12
Standard 55.4-75.4 1-10 59 24 16 50.4-65.4 16-23 37 22 9
2Alien
Technology
ALN-9762 “Short”
[Alien Higgs4]
Short Pitch —————51-541-3382418
Standard ——————————
Short Pitch 52-54 0-3 23 24 17 36-39 1-3 20 24 12
Standard ——————————
3Alien
Technology
ALN-9662 “Short”
[Alien Higgs3]
Short Pitch 36-39 0-4 16 23 14 57-63 1-4 43 24 23
Standard 38-62 0-3 60 24 18 48-58 15-24 60 24 17
Short Pitch 38-48 0-4 40 24 16 58-63 1-4 20 24 13
Standard 38-58 0-4 60 24 18 43-58 19-23 60 24 17
4Alien
Technology
ALN-9730 “Squiglette”
[Alien Higgs 4]
Short Pitch —————51-541-4362419
Standard ——————————
Short Pitch —————41-592-4202412
Standard ——————————
5Alien
Technology
ALN-9630 “Squiglette”
[Alien Higgs 3]
Short Pitch 48-53 2-4 19 24 17 41-44 0-1 19 24 10
Standard 43-53 13-16 54 24 16 43-63 15-25 55 24 15
Short Pitch 47-53 0-7 21 24 18 41-44 0-1 20 24 14
Standard 42-48 1-5 57 24 18 43-63 15-23 56 24 14
6Avery
Dennison
AD-226iL
[NXP UCODE G2iL]
Short Pitch 48.5-51.5 3-7 19 23 14 50.5-60.5 0-3 38 24 19
Standard 48.5-65.5 13-17 50 24 15 50.5-65.5 20-30 60 22 14
Short Pitch 55.5-65.5 4-6 20 23 11 50.5-55.5 0-4 38 23 17
Standard 55.5-70.5 13-17 55 23 18 50.5-65.5 20-25 57 24 14
7Avery
Dennison
AD-233m5
[Impinj Monza5]
Short Pitch 47-49 2-3 19 24 15 38-48 4-6 38 24 17
Standard 37-48 15-22 60 23 16 43-63 15-26 64 22 18
Short Pitch 42-44 2-3 19 24 12 38-48 4-6 38 24 16
Standard 37-53 0-26 60 23 21 38-58 15-25 60 21 17
8Avery
Dennison
AD-227m5
[Impinj Monza5]
Short Pitch 65.5-75.5 0-4 18 23 12 50.5-75.5 1-7 37 24 20
Standard 50.5-60.5 12-19 59 20 15 50.5-70.5 20-29 58 18 12
Short Pitch 55.5-70.5 1-3 23 24 13 55.5-70.5 0-3 19 24 10
Standard 50.5-60.5 13-19 52 20 14 50.5-55.5 20-25 20 15 8
9Avery
Dennison
AD-232iL
[NXP UCODE G2iL]
Short Pitch 38-57 1-4 37 24 16 41-44 0-6 38 23 14
Standard 43-62 2-5 60 24 15 43-53 17-24 65 24 18
Short Pitch 46-49 1-2 40 24 18 43-58 1-6 20 23 11
Standard 38-57 1-5 60 24 19 — — — — —
10 Avery
Dennison
AD-318m5
[Impinj Monza5]
Short Pitch ——————————
Standard 35-50 16-25 62 24 21 40-55 14-25 42 24 16
Short Pitch ——————————
Standard 40-50 12-16 54 24 19 33-53 10-21 58 24 18
11 SMARTRAC Belt M5
[Impinj Monza5]
Short Pitch ——————————
Standard 40-57 13-21 56 23 19 48-63 20-25 59 23 16
Short Pitch ——————————
Standard 38-57 13-20 59 23 18 43-63 20-24 63 23 18
12 SMARTRAC Belt
[NXP UCODE G2iL]
Short Pitch ——————————
Standard 38-52 2-6 58 23 17 — — — — —
Short Pitch ——————————
Standard 38-52 2-6 60 24 18 — — — — —
13 SMARTRAC Short Dipole i
[NXP UCODE G2iL/iM]
Short Pitch 52.5-55.5 1-3 18 24 16 55.5-65.5 0-2 20 24 15
Standard 48.5-53.5 12-23 58 24 19 47.5-50.5 16-22 25 24 12
Short Pitch 52.5-55.5 2-4 19 24 15 47.5-55.5 0-2 20 24 14
Standard 50.5-70.5 1-5 59 24 20 47.5-55.5 16-21 36 24 12
14 SMARTRAC ShortDipole
[Impinj Monza 5]
Short Pitch 47-50 1-3 20 24 16 53-58 0-2 19 24 12
Standard 47-70 5-14 58 20 16 48-58 18-26 60 22 17
Short Pitch 47-60 2-4 35 24 15 48-53 0-2 20 24 12
Standard 47-70 7-18 59 20 16 48-58 16-26 61 22 16
15 SMARTRAC DogBone i
[NXP UCODE G2iL/iM]
Short Pitch ——————————
Standard 46-76 2-14 66 23 15 52-62 15-22 37 20 8
Short Pitch ——————————
Standard 46-66 0-16 66 23 13 52-62 12-21 38 23 9
16 SMARTRAC DogBone i
[Impinj Monza4 QT]
Short Pitch ——————————
Standard 51-77 3-17 65 16 13 52-67 15-21 29 16 7
Short Pitch ——————————
Standard 51-57 2-13 29 13 10 52-57 11-20 33 16 7
17 SMARTRAC Viper
[Impinj Monza4D]
Short Pitch 62-73 2-7 19 24 10 — — — — —
Standard 57-68 10-20 53 22 16 62-68 18-25 25 13 7
Short Pitch 57-68 0-5 23 24 18 — — — — —
Standard 57-68 8-16 25 23 16 57-68 17-23 22 13 7
Feed Direction
The arrow in the header of table
indicates the direction in which labels
are output from the printer.
Placement and Configurations valid
for European (ETSI ) frequency
range, 865-868MHz
Valid for Frequencies that fall within
the FCC range, 902-928MHz