sauter TVL User manual

Sauter GmbH
Ziegelei 1
D-72336 Balingen
e-mail: [e-mail]
Phone : +49-[0]7433- 9933-0
Fax: +49-[0]7433-9933-149
Internet: www.sauter.eu
Instruction manual manual test bench
SAUTER TVL/TVL-XL
Version 2.1
11/2021
GB
TVL_TVL-XL-BA-e-2121
PROFESSIONAL MEASURING

2 TVL_TVL-XL-BA-e-2121
GB
SAUTER TVL/TVL-XL
V. 2.1 11/2021
Instruction manual manual test bench
Thank you for purchasing the manual crank test stand from SAUTER. We hope that
you will be very satisfied with the high quality of this measuring system with its high
reproducibility. For any questions, wishes and suggestions please do not hesitate to
contact us.
Table of contents:
1Scope of delivery........................................................................................... 3
2Technical description.................................................................................... 3
2.1 Technical data test bench ....................................................................................................... 3
2.2 Technical data length measuring unit LA (without serial interface) ................................... 3
3Maintenance................................................................................................... 3
4General safety instructions........................................................................... 4

TVL_TVL-XL-BA-e-2121 3
1 Scope of delivery
•SAUTER TVL
•A hook
2 Technical description
2.1 Technical data test bench
TVL
TVL-XL
maximum force
500N
Measurement direction
vertical and horizontal
Spindle stroke per
revolution
3mm
Mounting height of upper
hook from base plate
Approx. 470mm
Approx. 720
Thread hook
M6
Spindle height from base
plate
230mm
Thread of the encoder
mounting plate
4x M3 (included in delivery)
Workspace
Approx. 200mm
Approx. 450mm
Weight
8kg
15kg
2.2 Technical data length measuring unit LA (without serial interface)
TVL
TVL-XL
Scale length
200mm
Readability
0,01mm
Control buttons
On/0
•Switch on
•Zeroing the display of the LA
mm/in
Change of units between millimeters and inches
▲
Manual length preselection, upwards
▼
Manual length selection, downwards
3 Maintenance
To avoid rust, the test stand should be cleaned with a soft cloth after each use.
Under no circumstances should aggressive cleaning agents be used.

4 TVL_TVL-XL-BA-e-2121
4 General safety instructions
WARNING
Risk of injury due to overridden functions of the protective devices!
Overloaded functions of the protective devices can lead to severe
Injuries lead.
● Never override the functions of the protective devices, either yourself or by third parties.
● Never test with protective devices disabled.
● Never tamper with protective devices.
● Comply with all safety instructions.
WARNING
Risk of injury from falling parts!
Falling parts can cause serious injuries.
● Only use suitable and technically flawless lifting gear.
● Use lifting equipment with sufficient lifting capacity.
● Carefully fasten individual parts and larger assemblies with lifting gear.
● Secure individual parts and larger assemblies with lifting gear.
● Make sure that there is no danger from the hoist.
● Lift individual parts and larger assemblies slowly.
WARNING
Risk of injury from rotating components!
The drive can start automatically. Rotating components such as spindles on the drive
of the crosshead or the extensometer can catch long hair, loose clothing as well as sleeves or jewelry.
This can lead to serious injuries.
● Work only in clothing with tight-fitting sleeves.
● Wearing jewelry while working on the test system is prohibited.
● Use hairnet if necessary.
● Wear suitable protective equipment
WARNING
Risk of injury when handling in the test room!
When handling in the test room during the
operation of the test system, there are
Risk of injury. Your hands and arms can be
pinched and crushed.
● Never handle in the test room while the test
system is running.
● Never handle anything in the test room during
a test.

TVL_TVL-XL-BA-e-2121 5
WARNING
Danger of tipping due to use of heavy
specimens!
In the case of heavy specimens that are inserted
off-center, as well as due to improper
Behavior can tip the test system.
● Ensure that the test system is securely
positioned.
Never use the test system as a climbing aid.
CAUTION
Risk of injury!
There is a risk of injury when working on/with the test system.
● Comply with the applicable and binding national regulations on the
accident prevention.
Comply with the recognized technical rules for safety and
professional work.
Comply with the regulations on health and safety at work.
Provision of work equipment and its use.
● Observe company regulations such as supervision and reporting requirements.
● Read the operating instructions completely.
● Read the operating instructions and data sheets of external components
all the way through.
● Observe all safety instructions in the operating instructions.
● Observe all safety signs attached to the test system.
● Always wear appropriate safety equipment.
NOTE
Work on the test system may only be carried out by specialists qualified for this work.
be carried out.
NOTE
Only one operator may work on the test system at a time.
- During operation, the operator's workplace is located in front of the