Savant PAV-AIM7C User manual

PAV-AIM7C Quick Reference Guide | 009-1945-01 1 of 2 45 Perseverance Way, Hyannis, MA 02601
Copyright 2021 Savant Systems, Inc | 210901 Savant.com | 508.683.2500
Box Contents
(1) 7 Source Audio Input IP Transmitter (PAV-AIM7C-xx)
(1) Installation Kit (075-0194-xx)
(2) 6-pin Control Connector (028-9352-xx)
(1) 5V DC 3A Power Supply (025-0216-xx)
(1) Product Regulatory Statement (009-1950-xx)
Specifications
Environmental
Temperature 32° to 104° C (0° to 40° C)
Humidity 10% to 80% Relative Humidity (non-condensing)
Dimensions and Weight
Height Width Depth Weight
Device 1.6 in
(4.15 cm)
8.5 in
(21.50 cm)
3.7 in
(9.33 cm)
1.4 lb
(0.64 kg)
Shipping 2.2 in
(5.58 cm)
12.0 in
(30.48 cm)
7.3 in
(18.54 cm)
2.3 lb
(1.05 kg)
Power
Input 5V DC 3A
Maximum 15 Watts
Power over
Ethernet (PoE) (PAV-AIM7C-10 and -20 Only) IEEE 802.3af
Networking
Supported
Standard
IEEE 802.1 AVB/TSN switches
IEEE 802.3 Ethernet
Regulatory
Safety and
Emissions
FCC Part 15 CE C-Tick UKCA
RoHS Compliant
Supported Releases
PAV-AIM7C-00
PAV-AIM7C-10 da Vinci 8.10.2 and higher
PAV-AIM7C-20 da Vinci 9.4.3 and higher
Network Requirements
For networking guidelines and recommendations, refer to the Savant
Device Networking Guidelines available on the Savant Community
Knowledge Base.
Front Panel
Power Status
A B
APower LED
Green: System has power and is operating
normally.
O: System is not receiving power.
BStatus LED
O: Embedded processor is resetting, or is
powered up, and is booting the embedded
firmware.
Green: Host has established communications with
the embedded system.
Green Blinking: Embedded system is ready, but
no communication has been established with the
host.
Red: Host has determined the firmware needs to
be updated, but a problem occurred during the
process that will initiate a reset.
Red Blinking: Embedded firmware is running, but
has not received a DHCP IP Address.
Amber: Host is updating the embedded
firmware.
Amber Blinking: Embedded system has a valid
link-local IP Address and is connecting to the
host.
Installation
The PAV-AIM7C should be installed on a solid, flat, level surface. The
device will fit on a 1U rack shelf. The location should be dry, well
ventilated, and out of direct sunlight.
IMPORTANT! The PAV-AIM7C must to be connected to an AVB Switch.
A Savant AVB audio output device is also required.
Rack
The optional RMB-PAVAM2F-xx or RMB-PAVAM2-xx allows two
devices to be mounted side by side. This rack is compatible with all
standard 19-inch National Electrical Manufacturers Association (NEMA)
rack mounts.
The instructions below show the RMB-PAVAM2F-xx, both brackets
install the same way, face opposite directions.
1. Align the bracket with the device’s mounting points.
2. Attach using the screws provided with the bracket.
Savant® ProAV 7 Source Audio Input IP Transmitter with Control (PAV-AIM7C)
Quick Reference Guide

PAV-AIM7C Quick Reference Guide | 009-1945-01 2 of 2 45 Perseverance Way, Hyannis, MA 02601
Copyright 2021 Savant Systems, Inc | 210901 Savant.com | 508.683.2500
Rear Panel
3
RS232-2
RS232-1
Reset
+
4
-+
1
5
-6
+-+
2
IR
-3
-
+ +
Digital Audio In
D2D1
D3
D4
D3
Analog Audio In
1 2 M/N S/N UID
PoE
Ethernet
L
R
5VDC
A B C D E F G H
AReset
Resets the network settings of the device.
Hold Reset Button for 5 seconds while powered
on to clear network settings. Status LED will
rapidly blink red when reset is complete.
BRS-232
8-pin RJ-45 port used to transmit and receive
serial binary data to and from serial controllable
devices.
CTS/RTS handshaking availability based on
component profile. See RS-232 Connections
section for pin-outs.
CIR
(6) IR Ports
Uses 6-pin Control Connectors to send IR signals
to control devices with an IR input or IR receiver
via an IR flasher (5V tolerant only). See IR Wiring
section for important precautions regarding IR
functionality before making any connections.
DDigital Audio
In (Optical)
(2) Digital optical audio inputs (TOSLINK).
Supports up to 96kHz/24-bit digital audio in;
PCM stereo format only.
EDigital Audio
In (Coaxial)
(2) Digital coaxial audio inputs (S/PDIF).
Supports up to 96kHz/24-bit digital audio in;
PCM stereo format only.
FAnalog
Inputs
(3) Analog stereo inputs, RCA line-level inputs;
22 kΩinput impedance
GEthernet
8-pin RJ-45 port, PoE (802.3af compliant).
10/100/1000 Base-T auto-negotiating port with
Link/Activity LEDs.
Supports Audio Video Bridging (AVB).
Activity LED (left):
Green Blinking - Activity (Rx/Tx).
O - No Activity.
Link LED (right):
Green Solid - Ethernet Link is established.
O - Ethernet link is not established.
Supports Power over Ethernet on the PAV-
AIM7C-10 and -20 versions only.
H
Power Input 5V DC 3A
IR Wiring
IR connections are made using
6-pin control connectors supplied
with the device. The wire slips into
the hole and locks with a screw
located at the top of the
connector.
IMPORTANT: IR Wiring Precautions
Ensure that all IR emitters are within 15 feet (4.6 meters) from the
controller’s location.
Use of 3rd party blinking IR emitters with Talk Back is not
recommended. These types of emitters can draw voltage away from
the IR signal that can degrade IR performance.
NOTE: While not shown in the diagram above, IR connections 4 to 6
follow the same wiring as 1 to 3.
RS-232 Connections
Pins 7 and 8 are only required
for CTS/RTS handshaking.
IMPORTANT: When wiring to
this port, do not connect any
wires within the cable that
are not required for
communication.
NOTES:
–CTS/RTS handshaking is supported for flow control based on
the profile used in the configuration.
–Wire coloring is included to identify the pins used for this
connection. Colors shown do not represent any wiring standard.
–The ProAV 7 Source does not support RS-422/485.
RJ-45 TO DB9 ADAPTERS: Savant oers RJ-45 to DB9 adapters in a
variety of configurations that can be used for RS-232 control.
Refer to the RS-232 Conversion to DB9 and Pinout Application Note
located on the Savant Customer Community for more information on
RJ-45 to DB9 adapters.
Expansion
Savant AVB devices can be connected in a single system, providing a
virtual audio switch that can be configured to suit almost any need.
The maximum number of devices verses based on the active da Vinci
runtime.
Additional Documentation
Refer to the following documents located on the Savant Customer
Community for additional information.
–Savant IP Audio Deployment Guide (009-1571-xx)
Use white stripe
for positive (+)
432
1
Pin 1 IR 1 -
Pin 2 IR 1 +
Pin 3 IR 2
-
Pin 4 IR 2 +
- 1 + - 2 +
Pin 5 IR 3
-
Pin 6 IR 3 +
65
- 3 +
Pin No Connection
Pin No Connection
Pin No Connection
Pin GND
Pin RXD
Pin TXD
1
2
3
4
5
6
Pin CTS
Pin RTS
7
8
(RS-232)
(RS-232)
(RS-232)
(RS-232)
(RS-232)
RJ-45 Connector
(Gold pins facing up)
Pin 1 Pin 8