PAV-VIMVP1F/PAV-VIMVP1C | 009-1603-00 | 180411
Copyright 2018 Savant Systems, LLC
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
2 of 2
Item Description
Power Input 12V DC
DP In Not Used
HDMI In
19-Pin Type A HDMI female digital audio/video
input.
Supports HDMI 2.0a
HDMI 2.0 complaint cable required for 4K
content.
Optical
or
10 GbE
10G connection from the IP Video 10G switch.
SFP+ (PAV-VIMVP1F)
RJ-45 (PAV-VIMVP1C)
ERS-232
4-pin Control Connector. Transmits and receives
serial data to and from serial controllable
devices. For pin-out information, refer to the
RS-232 Wiring section below.
IR OUT
3.5 mm IR Emitter connection. Transmits IR
signals via an IR Flasher (5V tolerant) to devices
with an IR input or IR receiver
IR IN Not Used
LAN (C)
1G of reserved network data bandwidth
commonly used to connect any network
compliant device to transmit its data onto the
Ethernet network by sharing the 10G network
link. 8-pin RJ-45 female connection.
IMPORTANT!: Do not connect this port to a
network switch.
ILink LED Solid Orange - Link is established.
O – No link established
JLink Activity
LED
Green Blinking - Indicates data activity.
O – No Activity
KAudio
3.5 mm (1/8 in) Audio connection.
For use information refer to the Savant IP Video
Deployment Guide on the Savant Customer
Community.
Rear Panel Wiring and Connections
IR connection are made using 3.5 mm IR
Emitter supplied with the device.
IR Wiring
Serial control connection are made
using a 4-pin Control Connector
supplied with the device. The wire slips
into the hole and locks with a screw
located at the top of the connector.
RS-232 Wiring
Enhanced small form-factor pluggable connection. Duplex LC
Multi-mode OM3 Fiber required.
Transport Distance
DAC cable 6ft (2m)
OM3 multi-mode fiber 1000ft (300m)
Optical In (PAV-VIMVP1F)
Additional Information
Refer to the following documents located on the Savant Customer
Community for additional information.
– Savant IP Video Deployment Guide (009-1551-xx)
– Savant IP Video Network Configuration Guide (009-1552-xx)
– Savant IP Video with Audio Processing Deployment Guide
(009-1621-xx)
RJ-45 10G Ethernet connection.
Transport Distance
Cat6 100ft (30m)
Cat6a 300ft (100m)
Cat7 300ft (100m)
10 GbE (PAV-VIMVP1C)
Installation
The Savant IP Video Transmitters can be mounted with the
included mounting brackets. If installing this unit behind a display,
ensure enough air can pass though the grooves on the top of the unit.
This will maximize heat dissipation. Savant recommends aligning the
grooves vertically as shown below. For more information see the
Savant IP Video Deployment Guide on the Savant Customer
Community.
Power
Input
HDMI
Connection
10G
Connection
GRXTX12V
432
1
PIN
PIN
PIN
PIN
1
2
3
4
12V Do Not Use
Transmit
Receive
Ground
DC 12V HDMI IN OPITCAL OUT RS232RS232 LAN(C)IR OUT IR IN AUDIO
-
+
12V TX RX G
DP IN
B
D
E
F
G
H
A
C I J
K
PAV-VIMVP1F
