Saxby Lighting Cosmo Manual

Instruction leaflet
Cosmo Spotlight
39616
www.saxbylighting.com Saxby Lighting Ltd. BH23 3PE
• Whenchangingabulb,alwaysswitchoffatthe
mains and allow the bulb to cool before handling.
Used bulbs should not be disposed of with household
waste. Please recycle where facilities exist.
• Alwaysusethecorrecttypeandwattagebulb.Using
the incorrect wattage bulb will damage the product.
• Useasoftclothtohandlebulbs,avoiddirectly
touching the bulbs as this will shorten their life.
• Unscrewtheglassshadesanticlockwise.Pullthebulb
outtoremove.
• Pushthenewbulbin.Replacetheglassbygently
screwing on.
Commissioning
Fitting/replacing bulbs
Foryoursafety,alwaysswitchoffthesupplybeforechanginglightbulbs,orcleaning.
Wasteelectricalproductsshouldnotbedisposedofwithhouseholdwaste.Pleaserecyclewherefacilities
exist.CheckwithyourLocalAuthorityorretailerforrecyclingadvice.
Recycling advice
Safety information
Werecommendcleaningwithasoftdrycloth.
Donotusesolventsorabrasivecleanersasthesecould
damage the finish.
Glassparts–Removeandwashinwarmwaterorjust
useadampcloth.Donotuseabrasivematerialsas
these will damage the finish.
This bulb is protected by a glass shade. This part must be replaced immediately should the glass
shade become cracked or damaged. This fitting must not be used without the glass shade in place.
Replace Cracked
Shade
18WG9
Mains Halogen
• Replacethecoverontheterminalblock.
• Lifttheproductintoplaceandalignthescrewholes
upwiththeholesonthebracket.
• Using the supplied allen key, tighten the screws to
secure.Takecarenottotrapanywiring.
• Replacefuseor circuitbreaker andswitch on. Your
light is now ready for use.
Iss.3 17122013

Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before
commencinganywork.
This unit must be fitted by a competent and qualified
electrician.
InstallinaccordancewithIEEWiringregulationsand
currentBuildingRegulations.
Topreventelectrocutionswitchoffatmainssupply
before installing or maintaining this fitting. Ensure
other persons cannot restore the electrical supply
withoutyourknowledge.
This light fitting should be connected to a fused circuit.
Ifreplacinganexistingfitting,makeacarefulnoteof
the connections.
Alwaysusethecorrecttypeandwattagebulb.Never
exceed the wattage stated.
Whenchangingabulb,alwaysswitchoffatthemains
and allow the old bulb to cool down before handling.
Dispose of used bulbs carefully and responsibly.
This product is suitable for dimming when used in
conjunctionwithadimmablelamp.Pleaseensure
verificationofdimmingabilitieswiththelamp
manufacture prior to use.
Wasteelectricalproductsshouldnotbedisposedof
with household waste. Please recycle where facilities
exist.Checkwithyourlocalauthorityorretailerfor
recyclingadvice.
Specification
Voltage: 240V 50Hz a.c.
Lamp: 1xMax.18WG9Halogen
IP rating: 44
Layout
Installation
Wiring
Havingcorrectlyidentifiedthewiringfromyourexisting
lightfitting,pullthewirethroughtheholeandconnectto
theconnectionblockinsidetheproductinthefollowing
way:
Check that...
• Youhavecorrectlyidentifiedthewires
• The connections are tight
• Noloosestrandshavebeenleftoutoftheconnection
block.
OUTSIDE ZONES
ZONE
2
ZONE
1
0.6m
0.6m
2.25m
Ceiling
Spotlightsgiveaconcentratedbeam
of light and must not be positioned
any closer than 0.3M (30cm) to the
illuminated surface.
This product is suitable for use in Zone
2 and outside Zones of a bathroom.
See diagram. If this unit is being
fitted in a room containing a bath or
shower,a30mARCDmustbeused,
in accordance with IEE regulations.
• Planthedesiredlayoutofthisfittingcarefully,
ensuring the cables will reach the distance between
thejunctionboxandthelightfitting
• Avoidlocatinganycablesinpositionsthatwould
causeahazard.Positioncablesandjunctionboxes
(not supplied) away from areas where they may be
atriskfrombeingcut,trappedordamaged
• Themainssupplycablemusthaveaminimumcross
sectional area of 1.0mm²
• Thisproductmustbemountedoutofarmsreach.
• Thisproducthasspecialprotectionagainstthe
ingress of moisture and is IP44 rated.
Existingfittingsmustbecompletelyremovedbefore
installationofanewproduct.Beforeremovingthe
existingfitting,carefully note the position of each set
of wires.
• Undothescrewsholdingthefixingbracketinplace
and set aside
• Holdtheproductinplaceandmarkthepositionofthe
holes.
• Ensuretheceilingiscapableofholdingtheweight
oftheproduct.Takecaretoavoiddamagingany
concealed wiring and pipes.The correct fixings should
beused.Ensurethereisajoistatthepointoffixingto
support the weight of the product.
• Fixtheceilingbracketintoposition.
NEUTRAL
EARTH (GREEN/YELLOW)
SWITCHED LIVE
BLUE (N)
GREEN/YELLOW
BROWN (L)
SUPPLY
LIGHT FITTING
4th BLOCK PROVIDED FOR LOOP
TERMINATION IF NECESSARY