SBC PCD7.D5 RF Series User manual

Saia Burgess Controls |1
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Product series
PCD7.D5xxCF and PCD7.D5xxRF
Conguration of the devices
User's SW-Manual

Saia Burgess Controls
2 |
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
The information contained in this document is provided for informational purposes only.
While e󰀨orts were made to verify the accuracy of the information contained in this docu-
mentation, it is provided 'as is' without warranty of any kind.
Third-party brands and names are the property of their respective owners.
Microsoft®, Win32, Windows®, Windows XP, Windows Vista, Windows 7, Windows 8,
Visual Studio are either registered trademarks or trademarks of the Microsoft Corporation
in the United States and other countries. Other products and company names mentioned
herein may be the trademarks of their respective owners.
The example companies, organizations, products, domain names, e-mail addresses,
logo, people, places, and events depicted herein are ctitious. No association with any
real company, organization, product, domain name, e-mail address, logo, person, place or
event is intended or should be inferred.

Saia Burgess Controls | 3
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Table of Contents
0 Table of Contents ............................................................................................................ 3
0.1 Document Process ............................................................................................. 4
0.2 Trademarks ......................................................................................................... 4
1 First and quick start of device ....................................................................................... 5
1.1 First start of the device ....................................................................................... 5
1.2 Conguration of the web client ........................................................................... 6
1.2.1 The Settings Page .............................................................................................. 6
1.2.2 The Web Browser Settings ................................................................................. 7
1.2.3 Congure the Network interface ......................................................................... 8
1.2.4 Finish Quick start ................................................................................................ 8
2 Touch screen calibration ............................................................................................... 9
3 Open the System settings menu ................................................................................... 10
3.1 The system settings ............................................................................................ 10
3.2 System ................................................................................................................ 11
3.3. Logs .................................................................................................................... 11
3.4 Date & Time ........................................................................................................ 11
3.5 Networks ............................................................................................................. 11
3.6 Plugins ................................................................................................................ 11
3.7 Management ....................................................................................................... 12
3.8 Display ................................................................................................................ 12
3.9 Restart ................................................................................................................ 12
3.10 Authentication ..................................................................................................... 13
3.10.1 x.509 Certicate .................................................................................................. 13
3.10.2 Certicate’s parameters ...................................................................................... 13
3.11 Web Browser ...................................................................................................... 13
3.12 Exit ...................................................................................................................... 13
4. Factory reset ................................................................................................................... 14
4.1 Create the recovery USB device ........................................................................ 14
4.2 Restore the device from USB ............................................................................. 14

Saia Burgess Controls
4 |
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Document Process | Trademarks
0.1 Document Process
Version Updated Author Comments
ENG01p 2020-04-22 D. Sch. - First draw in Word
ENG01 2020-07-20 M. H. - New format InDesign
ENG02 2020-07-29
2020-11-09
M. H.
M. H.
- Ch. 1.2.1 The Settings Page - picture added
- Linked the hyperlinks
0.2 Trademarks
Saia PCD® is a registered trademark of Saia-Burgess Controls AG.
Technical changes are subject to the latest technical developments.
Saia-Burgess Controls AG, 2020. © All rights reserved.
Third-party brands and names are the property of their respective owners.
Published in Switzerland

Saia Burgess Controls | 5
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
First start of the device
1 First and quick start of device
1.1 First start of the device
After starting up the device the rst time you are located on the settings page, you need to
login to the setup menu to congure the device. By default, the username and password
are admin.
After entering the conguration menu, the rst time. The user is forced to change the
admin password. This password must follow security requirements and must be remem-
bered all the time to be able to change the conguration of the device.
New password: _________________________________________________________
Note:
The password cannot be cleared or reset in case it is forgotten, a device fac-
tory reset to factory default will not recover the password. If you lost your admin
password of the device, please contact your local support agents to get the
password reset.

Saia Burgess Controls
6 |
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Conguration of the web client
1.2 Congurationofthewebclient
1.2.1 The Settings Page
The settings page is the default start page.
Enter you credentials to open the conguration menu or press Load Homepage on the
write top to access the conguration done in the web browser setup. If you download a
new application, you can force the panel to clear the cache.
On the HTML5 web application, pressing for 5 seconds on the top left corner of the web-
panel touch screen will open the settings page.
5 seconds

Saia Burgess Controls | 7
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Conguration of the web client
1.2.2 TheWebBrowserSettings
After entering the conguration menu, you are forwarded to the Web Browser congura-
tion. To change the web Browser conguration, press the button EDIT on the right top on
the page.
Change the “on start” behavior of the device
Item Default Description
On Startup Open settings page After a restart of the device the setting page is
displayed
Continue where you left Jump to the application where you left
Open homepage Open the congured Homepage
Homepage https://google.com Enter here the start page which you like to load as
homepage including http:// or https://

Saia Burgess Controls
8 |
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Conguration of the web client
1.2.3 ConguretheNetworkinterface
By default, all network interfaces a congured for DHCP. The ETH0 (For PCD7.D5xxCF
beside the power connector) is congured as WAN port. If you connect the panel to the
network using ETH0 and a DHCP server is running the Ip-Address is automatically re-
quested from the DHCP server.
If no DHCP server is available or can’t be used on site, the conguration can be changed
to static IP conguration. To congure the network interface, open the “Network” tab and
press the EDIT button on the top right.
Disable the DHCP switch will allow you to enter the IP-Address manually. After you press
save the manually entered IP address will be used for the device.
Note:
The device has an internal rewall which blocks all incoming network tra󰀩c,
including ICMP ping requests. Therefore, you can’t ping the device to test the
network connectivity.
1.2.4 Finish Quick start
The device is now correct congured to load the homepage you entered.
Therefore, you can close the setup menu to access the homepage by click EXIT in the
System Settings list. Depending on the Web Browser conguration “On Startup” the ap-
plication gets directly opened or you need to press Load Homepage on the Settings Page.

Saia Burgess Controls | 9
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Touch screen calibration
2 Touch screen calibration
System Setting Calibration allows to calibrate Touchscreen device and can be accessed
by the tap-tap procedure.
Tap-tap consists in a sequence of several touch activations by simple means of the nger
tapping the touch screen performed during the power-up phase and started immediately
after the HMI is powered on.
When “tap-tap detected” message appears on the top of the screen, wait for 5 seconds
(without touching the screen) to enter System Settings sub menu
Press on touch screen, “Touchscreen calibration” voice will be highlighted in yellow, hold
pressed for few seconds until touchscreen calibration procedure starts.
Follow the instructions on screen to complete the calibration procedure, system will
prompt to touch specic points to calibrate the touchscreen device.
In compliance with the above regulations the products are CE marked.

Saia Burgess Controls
10 |
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Open the System settings menu
3 Open the System settings menu
The system settings menu is entered after power on the device and entering valid creden-
tials “Username” and “Password” into the login mask.
3.1 The system settings
On the lift side in the system Settings screen the main topics of conguration is listed
Language Setup the language of the device
System System information, Status and Timers
Logs Congure logle generation
Date and Time Congure the date and time of the device
Network Congure the network settings of the Ethernet interfaces
Plugins Not used
Management Firmware updates and basic FW and booter congurations
Display Display setup like colors, timeouts and touch screen calibration
and more
Restart Restart the main or cong OS
Authentication Change passwords or create SSL certicates
Web Browser Congure the web browser properties like home page
Exit Will close the system settings view
Language Select the language for the system settings interface
■ System keyboard layout: select the layout of the virtual keyboard

Saia Burgess Controls | 11
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Open the System settings menu
3.2 System
Parameter Description
Info Device information
Status Device status (Free RAM, Up time, CPU Load)
Timers Device timers (System on, Back light on)
PlugIn Hardware plugins information (not used)
3.3. Logs
Set the persistent log option if you want maintain the log les saved after a power reset.
Use save button to export a copy of the log les.
The log les manager cyclically lls 3 les of 4Mb
3.4 Date & Time
Device date and time.
3.5 Networks
Network parameters. Available parameter in edit mode:
Parameter Description
Current Timezone Timezone region
Current Date
Local Time
Date and Time can set manually only when the Automatic Update is disabled.
Automatic Update (NTP) Enable to keep date and time synchronized from a remote server
■NTP Server
Specify the Internet NTP Server address
General Settings Device hostname
Avahi Hostname (see “Avahi Daemon” below)
Network Interface Network parameters of the available interfaces
■DHCP
■ IP Address
■ Net Mask
■ Gateway
DNS DNSServers
Generally provided from the DHCP servers, but can be modied in edit mode
Search Domains
Optional domains that will be used in concatenation with the provided urls
3.6 Plugins
This page will show the parameters available to congure the optional plugins modules
attached to the HMI device. See the description of each plug-in module to additional infor-
mation.

Saia Burgess Controls
12 |
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Open the System settings menu
3.7 Management
From the management area is possible “Update System Components” on page 18 of the
HMI device.
CAUTION:
Working in the Management area is a critical operation and, when not
performed correctly, may cause product damages requiring service of the
product. Contact technical support for assistance.
Use the “Clear” command inside the “Data” section to remove HMI Runt-
ime from the device (Factory Restore)
3.8 Display
Parameter Description
Brightness Brightness level of the display
Back light timeout Backlight inactivity timeout
Orientation Display orientation
3.9 Restart
HMI device restart command

Saia Burgess Controls | 13
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Open the System settings menu
3.10 Authentication
Enter in edit mode to change the authentication passwords.
3.10.1 x.509Certicate
HMI Device use a self-certicate to encrypt the Internet communication trough the HTTPS
protocol. You can personalize the certicate with the data of your Company and ask to a
Certicate Authority to rm it.
The procedure to personalize and rm your certicate is:
1. Enter in edit mode and ll the necessary parameters, then generate the new certicate
with your data.
2. Export the “Certicate Signed Request”
3. Sent the “Certicate Signed Request” to a Certicate Authority to rm it (general this is
a paid service)
4. Import the signed certicate into the HMI device
3.10.2 Certicate’sparameters
Parameter Description
Device Name The name of your device
Organization The legal name of your organization
Unit The division of your organization handling the certicate
State The state/region where your organization is located
Location The city where your organization is located
Country The two-letter ISO code for the country where your organization is location
Valid (days) Validity of the certicate
Key Length Number of bits of the key used from the cryptographic algorithm
3.11 WebBrowser
Parameter Description
On Startup,
open Settings page
After a restart of the device the setting page is displayed were you can enter
the setup menu or device conguration
On Startup,
continue were you left
After a restart of the device the last active page will be loaded. This setting does
not work for project having a runtime like the Web Editor 8 or supervisor and will
always start with the start page assigned for the project.
On Startup,
open homepage
After a restart of the device, the homepage is directly loaded
Selecting continue were you left or open homepage will now longer allow you to enter the
setup menu.
3.12 Exit
Exit from the System Settings.

Saia Burgess Controls
14 |
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Create the recovery USB device
4. Factory reset
The factory reset sets back the device properties and settings to factory default.
What you need:
1. A USB
2. The chromium runtime for the device un6x-chromium-xx-x.x.zip
4.1 Create the recovery USB device
Format the device with a FAT32 lesystem and copy the complete le
“un6x-chromium-xx-x.x.zip” onto the USB
4.2 Restore the device from USB
Plugin the recovery USB device to the Panel you like to reset. To start the factory reset
use the Tap-tap function consists in a sequence of several touch activations starting di-
rectly after powering on the device.
When “tap-tap detected” message appears on the top of the screen, wait for 5 seconds
(without touching the screen) to enter System Settings sub menu

Saia Burgess Controls | 15
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Restore the device from USB
don’t touch the screen to jump into the Default Mode of the device.
Open the Startup sequence
On the installed Apps on the left select the Chromium version and press Uninstall

Saia Burgess Controls
16 |
27-680 ENG02 – User's SW-Manual for the HMTL5 panels PCD7.D5xx
Restore the device from USB
2020-11-09 | Technical data and information subject to change.
Saia-Burgess Controls AG
Bahnhofstrasse 18 | 3280 Murten, Switzerland
T [phone] | F [phone]
www.saia-pcd.com
[email protected] | www.sbc-support.com
After both elds are empty press Install and browse to the le “un6x-chromium-xx-x.x.zip”
located on mnt/usbmemory
Select the le “un6x-chromium-xx-x.x.zip”and press install
Wait or press done to execute the restart sequence