SC&T HS10M User manual

1
HDMI Matrix Switcher Series
ITEM NO.: HS10M 10 x 10 HDMI Matrix Switcher
HS10M 10x10 HDMI Matrix Switch allows you to route 10 HD sources to any 10 HD displays! The 10x10
HDMI Matrix switch is a complete HD routing solution for whole home HDTV systems. It provides 3D
support, Full 1080P, and with 1U Rack mountable for professional installations. In addition, the HS10M
allows for effortless control of up to 10 devices through Ethernet control, Android/IOS App Control,
IR remote control, RS-232 and the front panel.
Features:
Connect up to 10 HDMI source to 10 x HDMI display monitors.
HDMI 1.4 with 3D, HDCP & DVI Compliant.
High definition video up to 1080p@60Hz@12bits.
Easy to use front panel control of switching or using the included remote control.
Built in Ethernet Control and Android/IOS App Control.
Built in RS232 console port to select input/output.
Input/Output status could be displayed at front panel LCM & LED.

2
1.0 HS10M Panel View:
2.0 HS10M Connection View:
4
INPUT OUTPUT
…………… ……………
IR01
SOURCE
…………….. ……………..
HDMI 1
CONSOLE
RS-232
IR Receiver
PC
HDMI 10
TV
TV
HDMI 1
HDMI 10
SOURCE
MATRIX
RJ45
ETHERNET

3
3.0 Keypad and LEDs
3.1 Back Panel Switch:
POWER Light on Power on
Light off Power off
3.2 Front LED Indication:
ON BLUE Power on
RED Standby
LED off Power Off
INPUT 1, 2, 3, 4 BLUE Signal indication
LED off No signal
OUTPUT 1, 2, 3, 4 BLUE HDMI output indications
LED off Output unlink
Standby mode: The IR Remote only could control POWER on/off.
Front Button Function:
Power Power on/standby
UP Up
DOWN Down
LEFT Left
RIGHT Right
ENTER Select confirm key
MENU Back to main menu
EDID Copy EDID
LOCK Button lock
ALL Set selected input channel to all output
When press ALL the second line of panel will show IN and
flashing, select the input 1~10 then press ENTER
OFF Turn off selected output, could be 1~10 or ALL
When press OFF the second line of panel will show IN and
flashing, select the input 1~10 or ALL then press ENTER
OUTPUT 1~10 Fast switch output
INPUT 1~10 Fast switch input
*When the sub-menu setting changed, press the ENTER key to complete the setting. If no press
ENTER key, then the setting will be failed.

4
3.3 LCM Panel Function:
10X10 HDMI MATRIX: Power on Main Screen
When the power is on and the main screen appears, press the MENU key to enter the main
menu
Main MENU Option:
*1 - SWITCH SETTING
*2 - MATRIX IR ID
*3 - ETHERNET
*4 - EDID
*5 - FIRMWARE VER.
*6 - MEMORY
Operation:
Press UP or DOWN key to move * to select an item for setting and press ENTER key to
enter into subpage.
In MENU you could use key 1~6 of IR remote control to select the functions.
When the selected sub-page setting is completed, press the MENU button to return to
the main page

5
4.0 LCM Main MENU Function Operations:
4.1 SWITCH SETTING：(Default: 1 2 3 4 5 6 7 8 9 10)
This function is used to switch the input/output port. Enter the SWITCH SETTING menu. Press the
ENTER key, then the LCM second line INPUT will flash. Press LEFT or RIGHT button to select the
output to be modified. Then press Up or Down button to select the input port. After that, press
ENTER to confirm setting.
4.2 MATRIX IR ID：(Default IR ID: 0)
This function must be set to match the Matrix remote control IR01 with the matrix itself. A
conflict with other devices remote control is avoided.
After entering MATRIX IR ID menu, press ENTER, the LCM LINE 1 number will flash. Then
Press UP or DOWN button to select the number, and then press ENTER to confirm.
When finish MATRIX IR ID setting, MATRIX remote control IR01 must also set the same ID
in order to operation in normal.
Remote IR ID setting mode: Press and hold the POWER button, then press the
number button which can be set from 0 to 9, total 10 groups. (See 5.1)
These settings on IR01 remote control have to be done the first time you use the IR01 or
when you change the batteries.
MATRIX IR ID 0
OUT 1 2 3 4 5 6 7 8 9 10
IN 1 2 3 4 5 6 7 8 9 10
+

6
4.3 Ethernet
* IP Address
Subnet Mask
Gateway
DHCP Client
Media Type
MAC Filter
IP Address: (Default: 192.168.0.200)
This function can be setup MATRIX host intranet ”IPAddress”, press the ENTER, the left-most number of
second row will flash, then press the UP or DOWN button to change the numbers, , press LEFT or RIGHT to
move to another location, the move to a position number will flash, press ENTER to complete the setting.
Subnet Mask: (Default 255.255.255.0)
This function can be setup MATRIX host intranet “Subnet Mask”, press the ENTER, the left-most number of
second row will flash, then press the UP or DOWN button to change the numbers Press the ENTER, , press
LEFT or RIGHT to move to another location, the move to a position number will flash, press ENTER to complete
the setting.
Gateway: (Default 192.168.0.1)
This function can be setup MATRIX host intranet “Gateway”, press the ENTER, the left-most number of second
row will flash, then press the UP or DOWN button to change the numbers Press the ENTER, , press LEFT or
RIGHT to move to another location, the move to a position number will flash, press ENTER to complete the
setting.
IP Address
192.168. 0.200
Subnet Mask
255.255.255.0
Gateway
192.168. 0. 1

7
DHCP Client: (Default Disable)
When DHCP Clients setup at “Enable”, the MATRIX host will automatically get IPAddress, Subnet Mask,
Gateway, if setup at “Disable”, the MATRIX Host IPAddress need go through “ETHERNET”menu to set IP
Address, Subnet Mask, Gateway, to press the ENTER, the second row will flash, then press the UP or DOWN
to select DISABLE, ENABLE, then press ENTER to complete the setting.
Media Type: (Default 100M)
This function can be setup MATRIX host intranet “Media Type, press the ENTER, the second row will flash,
then press the UP or DOWN button to select 10M, 100M, AUTO, press ENTER to complete the setting.
MAC Filter : (Default Disable)
MAC Filter can be setup with registered MACAddress in order to connect the MATRIX host Web UI, MAC
Address required by the Web page to fill in, this function can only be setup at “DISABLE”, “ENABLE”, then to
press the ENTER, the second row will flash, then press the UP or DOWN to select DISABLE, ENABLE, then
press ENTER to complete the setting.
DHCP Client
Disable
Media Type
100M

8
4.4 EDID: (Default: LPCM-2CH)
Because the player output display resolution will be based on TV EDID, this Matrix provides two
default EDID modes:” BUILD-IN MODE” and “COPY MODE”.
4.4.1 BUILD-IN MODE：
This mode supports video resolution 480p, 720p, 1080i / p at 24/50/60Hz, support LPCM
two-channel audio and 5.1 channel. After enter BUILD-IN MODE menu, press UP or DOWN key to
select LPCM-2CH or LPCM-5.1CH, then press ENTER to confirm setting.
BUILD-IN MODE：
This mode supports video resolution 480p, 720p, 1080i / p at 24/50/60Hz, support LPCM
two-channel audio and 5.1 channel. After enter BUILD-IN MODE menu, press UP or DOWN key to
select LPCM-2CH or LPCM-5.1CH, then press ENTER to confirm setting.
BUILD-IN MODE
COPY MODE
LPCM-2CH
LPCM-5.1CH
BUILD-IN MODE
COPY MODE
LPCM-2CH
LPCM-5.1CH
Player - 10
Player - 2
Player - 1
HS10M
LPCM-2CH
LPCM-5.1CH
HDMI –10
EDID
HDMI –2
EDID
HDMI –1
EDID

9
COPY MODE：
To fully support the TV resolution and audio mode, the matrix provides “copy mode”to copy TV
EDID for input source reference. When use the copy mode, recommend copying the lowest
resolution TV EDID. Otherwise it may cause no picture display if the TV resolution is not able to
support higher resolution.
After entering COPY MODE menu, press UP or DOWN button to select the OUTPUT (1 to 10). Then
press ENTER. Press UP or DOWN button to select the INPUT (1 to 10). Then press ENTER to confirm.
4.5 FIRMWARE VER.:
Display HS10M Matrix firmware version
4.6 MEMORY:
MEMORY function is to fast reload channel setting for different application.
SAVE
Save current channel setting, could be 1~10
LOAD
Reload saved channel setting, select the number of setting and press ENTER
From OUTPUT: 1
To INPUT: 1
HS04M
HDMI –IN10
LPCM-2CH
HDMI - IN2
LPCM-2CH
HDMI - IN1
TV1 EDID
From OUTPUT: 1
To INPUT: 1
TV1 EDID
Player - 10
Player - 2
Player - 1
HDMI - OUT 10
HDMI - OUT 2
HDMI - OUT 1
FIRMWARE VER.
VERSION 1.00
SAVE MEMORY 1
SAVE
LOAD
LOAD MEMORY 1
1 2 3 4 5 6 7 8 9 10

10
5.0 Remote Control Function (IR01):
5.1 To command the matrix locally, setup the remote control IR01 ID with the same code
of the Matrix (see 4.2). The default code is 0. (Power+0)
5.2 Warning: These settings have to be done the first time you use the IR01 or when you
change the batteries.
IR ID setup : press and hold POWER button , then press Number key
Remote control button define:
Symbol Function Side
Power ON/Standby (same as Matrix)
LEFT Left (same as Matrix)
RIGHT Right (same as Matrix)
UP Up (same as Matrix)
DOWN Down (same as Matrix)
ENTER Confirm (same as Matrix)
MENU Menu (same as Matrix)
Quick key1
Quick key2
Quick key3