SC&T SP006PH-10G User manual

Smart Cabling & Transmission Corp. V1.0
Surge Protector Series
User Manual
Model : SP006PH-10G
High Performance 10G PoE Surge Protector

1
User Manual
SP006PH-10G
Introduction
SP006PH-10G is an in-line surge protector designed for preventing damage to PoE (Power over Ethernet)
devices from high voltage surges.
Features
•Surge current up to 20KA
•Supports data rate up to 10Gpbs
•Supports Mid-Span and End-Span PoE
•Built-in two stage protection with GDTs and SIDACTORs
•Supports protection for both differential and common mode
•Response time less than 1ns
•IEC 61000-4-2, IEC61000-4-5, UL497B compliance
•Supports multiple mounting options (Wall/Rack mounting & Din-Rail)
Installation view
Bandwidth/Distance
For 10G application, the maximum distance is 80M. SC&T uses COMMSCOPE CAT6a cable for testing, the
data rate may be slightly compromised by connected equipment, cables, and connectors.

2
User Manual
SP006PH-10G
Panel view
Front Rear
No Interface Function
1
Input Connector
To connect the cable transmission side
2
GND Connection
To connect the ground
3
Protected Connector
To connect the device to be protected
RJ45 Pin Define
( TIA/ EIA-568-B )
Pin
Pin Color
1
Orange-white
2
Orange
3
Green-white
4
Blue
5
Blue-white
6
Green
7
Brown-white
8
Brown

3
User Manual
SP006PH-10G
Caution
•This product is not water resistant. If it is desired for outdoor use, please install additional
equipment for waterproof protection.
•Avoid using this product close to water places, or near high temperature devices such as
radiators, stoves, etc.
•Using standard and certified Ethernet CAT5e UTP/STP/FTP, CAT6 UTP cables is recommended.
•10G full speed cannot be reached when transmission distance is longer than 80M.
•Only the port marked “protected” can prevent your PoE device from surges, so we recommend
using a SP006PH-10G for each of your PoE device that needs to be protected.
•Ensure the input port connects to a network cable as below.
sssss
•To effectively protect your PoE device, please ensure the product is properly grounded.
•DO NOT connect the ground wire to power wire.
•The ground resistance value should be less than 100Ω.
•The protection is not bi-directional, the protected device must be connected to the Protected
Connector.
•To have the best performance, using high-quality CAT6a cables and RJ45 connectors is
recommended.
What’s in the Package
No. Item Qty
1
SP006PH-10G
x 1
2
Accessory Set
x 2

4
User Manual
SP006PH-10G
Specification
ITEM NO. SP006PH-10G
Support
Compliance
IEEE 802.3af PoE
IEEE 802.3at PoE+
IEEE 802.3bt PoE++
Passive PoE Compatible
IEC 61000-4-2 Standard
IEC 61000-4-5 Standard
UL497B
Data Rate
10/ 100/ 1000/ 10000Mbps
Operation Voltage
< 58V
Operating Current
8A
Surge Discharge Current
20KA (8/20us)
Peak Pulse Current
200A (10/1000us)
Protection Mode
Differential and Common Mode
Insulation Resistance
> 10000Ω.
Capacitance (line to line)
< 2.5pF
ESD Protection
± 30KV (Contact & Air)
Ports & Interfaces
Data Input
1 x RJ45
Data Output
1 x RJ45
Ambient Temperature
Operation
-40 to 70℃
Storage
-40 to 90℃
Max. Operating Altitude
2000m
Humidity
Up to 95%
Physical Characteristics
Mounting
Rack-Mount / Wall-Mount / Din-Rail
Dimensions
50 x 80 x 32mm
Weight
160g

5
User Manual
SP006PH-10G
Installation Guide
Accessory
A Machine Screw
B Self-drilling Screw
C Screw Plug
D Angle Bracket
E DIN-rail Mounting Plat
F 1U Rack
Installed on a Platform
Step 1 Use machine screws to fix angle brackets on both sides of your product

6
User Manual
SP006PH-10G
Step 2 Use self-drilling screws to fix the product on a platform
Step 3Move the product to get fixed and then lock the screws

7
User Manual
SP006PH-10G
Installed on Wall
Step 1Same way as “Installed on a Platform”, but need to put screw plugs into the wall before inserting
the screws (leave 2mm space from the platform)
Installed on a Din-Rail
Step 1Use machine screws to fix a din-rail mounting plat on the side of your product

8
User Manual
SP006PH-10G
Step 2Install your product on a DIN-rail as following instruction
Installed on a Rack
Step 1Lock machine screws in the rack
Step 2 Put your products on the rack

9
User Manual
SP006PH-10G
Step 3Push the products to the other side of the rack
Step 4Install the rack in a cabinet