Scantech Shuttle SG-15 COLOUR User manual

The Federal Communication Commission Statement
This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. T
his equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction, may cause harmful interference to
radio communication. However, there is no guarantee that interference will not occur
in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one of more of the following measures: -
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced Radio/TV technician for help.
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that change or
modifications not expressly approved by the party responsible for compliance could void yo
ur authority to
operate the equipment.
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
1
This device may not cause harmful interference and
2 This device must accept any interference received, including interference that may cause undesired
operation.
The antenna used for this transmitter must not be collocated or operation in conjunction
with any other antenna or transmitter.
Notice : The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change
to the antenna or the device is permitted. Any change to the antenna or the device could result
in the device exceeding the RF exposure requirements and void user’s authority to operate
the device.

The antenna(s) used for this transmitter must not be co-located of operating in
conjunction with any other antenna or transmitter.
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. Ln order to avoid the possibility of exceeding the
Fcc radio frequency exposure limits, human proximity to the antenna shall not
be less than 20cm (8inches) during normal operation.

Copyright © 2016, Scantech-ID BV.
This manual is copyrighted, with all rights reserved. Under the copyright laws, this manual may not, in whole
or in part, be copied, photocopied, reproduced, translated or converted to any electronic medium or
machine readable form without prior written consent of Scantech-ID BV.
Limited Warranty
Under all circumstances this manual should be read attentively, before installing and/or using the product.
In no event shall Scantech-ID BV be liable for any direct, indirect, special, consequential or incidental
damages arising out of the use or inability to use this documentation or product, even if advised of the
possibility of such damages. In particular, Scantech-ID BV shall not be liable for any hardware, software, or
data that is stored or used with the product, including the cost of repairing, replacing or recovering the
above. Scantech-ID BV reserves the right to change parts of the device at any time without preceding or
direct announcement to the client.
Scantech-ID BV reserves the right to revise this manual, and to make changes in the contents without
obligation to notify any person or entity of the revision or change. A serial number appears on the product.
Make sure that this official registration number has not been removed. It should be used whenever servicing
by Scantech-ID BV or an authorised Scantech dealer is necessary.
Important
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
EN55022, and with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the user’s manual, may cause harmful interference to radio
communications. Operation of the equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense. Any unauthorised
changes or modifications to this equipment could void the user’s authority to operate this equipment.
The ShuttleC is in conformity with the CE standards. Please note that a Scantech CE-marked power supply
unit should be used to conform to these standards.
Radio and television interference
Operation of this equipment in a residential area can cause interference with radio or television reception.
This can be determined by turning the equipment off and on. The user is encouraged to try to correct the
interference by one or more of the following measures:
•Re-orientate the receiving antenna
•Relocate the devices with respect to the receiver
•Move the device away from the receiver
•Plug the device into a different outlet in order to have the device and receiver on
different branch circuits
If necessary, the user should consult the manufacturer, an authorised Scantech dealer or experienced
radio/television technician for additional suggestions. The booklet "How to Identify and Resolve Radio-TV
Interference Problems", prepared by the Federal Communications Commission, can be of help. It can be
obtained from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004000003454.
P/N 0145-SIG5051 V3.04 Date: 12-08-2016 FW V0.9.3

1
Table of contents
Table of contents..........................................................................................1
Preface .................................................................................................3
Chapter 1 Product Safety............................................................................4
1.1 Used conventions .............................................................5
1.2 Laser safety.....................................................................5
1.3 Declarations of Conformity ................................................8
1.4 Product Labelling............................................................10
Chapter 2 General Description...................................................................11
2.1 Use of the ShuttleC..........................................................12
2.2 Construction of the ShuttleC.............................................13
2.3 Functioning of the ShuttleC...............................................14
2.4 Power Over Ethernet (PoE) ..............................................16
Chapter 3 Installation of the ShuttleC...........................................................17
3.1 Unpacking......................................................................18
3.2 Mounting........................................................................18
Chapter 4 System Integration....................................................................20
4.1 Software........................................................................21
4.2 How to communicate? A Simple example ..........................24

Preface 2
Chapter 5 Configuring the ShuttleC............................................................. 27
5.1 Making Connection and Login.......................................... 28
5.2 Wired network settings ................................................... 31
5.3 WiFi networksettings………………………………..............32
5.4 SG-15 Price Checker Settings ......................................... 37
5.5 Configuring the Bar Code Reader…..................................43
5.6 DeskTopConfigurator Which application to start at boot.... 45
5.7 Web Price Checker......................................................... 47
Chapter 6 Maintenance and Cleaning …………………………………………..51
Appendices ………………………………………………………………………..55
AConnector types and pin definitions ................................. 56
BControlling the display and ShuttleCterminal ..................... 57
CCharacter sets............................................................... 63
DFactory Default Settings.................................................. 65
EUpdating Applications or System Packages...................... 66
GFrequently Asked Questions ............................................ 67
HShuttleCProject tasks ..................................................... 71
ITechnical specifications.................................................. 72
JOverview Partnumbers.................................................... 74
KShuttleCDemonstration program …...……………… ......... 75
LWiFi info ........................................................................ 77
M.................................................................................... 77
N ShuttleCControl Bar Codes...............................................78
P Drilling Template for Easy Mounting.. ...............................81
Q Product Summary What's new at the SG-15Colour……….. ..89

Preface
The ShuttleCis an entry level, small and attractive Price Checker.
The ShuttleC features the latest technology. Interfacing is done either through
Wireless RF or hard wired Ethernet. The bright colour display has, depending on
the used font set, 3 or 5 lines and can display up to 20 characters per line.
There is a choice of bar code scanners between the high performance 24 scan
lines laser scanner, 2D imager and the low cost single scan line CCD scanner.
Because of its size and the sympathetic good looks the ShuttleCcan be installed
anywhere in a store, including on the shelves. This flexibility of installation is
enhanced by the optional Power-over-Ethernet. The three available standard
colours also greatly help to fit most interiors.
General Information
The Scantech-ID ShuttleCis the latest product developed by the company that
has over 20 years of experience in the field of customer information systems.
Today we offer a choice of scanner (Laser 24 omni directional lines, 2D Imager
and CCD single line), a choice of colour (Silver, Black or Red) and a choice of
interface (LAN, WiFi POE).
Quality and Durability
The ShuttleCcomes with the same top quality as all other Scantech-ID products.
So at a very competitive price the same quality and performance of more
expensive products is available. Due to the high MTBF times of every component
a long and service free operation time is secured.
Flexibility
The size of 182mm (height), 131mm (width) and 95mm (depth), makes the
Scantech-ID ShuttleCsmall enough to be installed in larger numbers per store.
Even when mounted on a shelf it will not block products on display.
The bright display makes it easy to read prices and product information.
Connectivity
The ShuttleCis configured using a standard web browser.
A customized application program -not supplied by Scantech-ID- is necessary
for retailers to operate the SG-15Colour in their specific environment. Scantech
supplies software source code examples plus network drivers for easy
integration.

Chapter 1 Product Safety

Scantech-ID ShuttleCSG-15Colour 5
1.1 USED CONVENTIONS
In this manual the following conventions are used:
ATTENTION
Gives a tip, an instruction or a point of attention.
IMPORTANT
Warns for possible damage to the scanner or other objects when not
following an instruction.
DANGER!
Warns for possible harm to persons when not following an
instruction.
1.2 LASER SAFETY
ATTENTION
During installing, always follow the instructions.
DANGER!
Do not stare into the laser beam. The laser safety is in conformity
with IEC 825 and 21CFR140.

6 Product Safety
German:
Der Strichcode-Scanner SHUTTLEC entspricht den Sicherheitsvorschriften nach IEC 825-1 (1993) für
ein Laserprodukt der Klasse I. Er entspricht auch U.S. 21CFR1040, anwendbar auf ein Laserprodukt
der Klasse IIa. Vermeiden Sie langzeitiges Hineinblicken in direktes Laserlicht.
Dutch:
De SHUTTLECscanner voldoet aan de veiligheidsnormen IEC 825-1 (1993) voor een Klasse I
laserproduct. Tevens voldoet de scanner aan U.S. 21CFR1040, van toepassing op een Klasse IIa
laserproduct. Vermijd langdurig kijken in direct laserlicht.
French:
Le scanner SHUTTLEC est conforme aux normes de sécurité IEC 825-1 (1993) s’appliquant à un produit
laser de la classe I. Il est également conforme à la U.S. 21CFR1040 telle qu’elle s’applique à un
produit laser de la classe IIa. Eviter de rester exposé longtemps à la lumière directe du laser.
Danish:
SHUTTLECskanneren er i overensstemmelse med sikkerhedsstandarden IEC 825-1 (1993) for
laserprodukter i klasse I. Den er også i overensstemmelse med U.S. 21CFR1040, der gælder for
laserprodukter i klasse IIa. Undgå at se direkte på laserlys i længere perioder..
Finnish:
SHUTTLEC-skanneri täyttää luokan I lasertuotteelle IEC 825-1:ssä (1993) asetetut turvavaatimukset. Se
täyttää myös U.S. 21CFR1040:ssa asetetut vaatimukset siltä osin kuin ne koskevat luokan IIa
lasertuotetta. Vältä pitkäaikaista suoraan laservaloon katsomista.
Swedish:
Avsökaren SHUTTLECuppfyller säkerhetsnormen IEC 825-1 (1993) för laserprodukter av klass 1. Den
uppfyller dessutom U.S. 21CFR1040 som gäller för laserprodukter av klass IIa. Undvik att titta i direkt
laserljus under längre perioder.
Norwegian:
SHUTTLECskanneren er i samsvar med sikkerhetsstandarden IEC 825-1 (1993) for laserprodukter i
klasse I. Den er også i samvar med U.S. 21CFR1040 for laserprodukter i klasse IIa. Unngå å se
langvarig på direkte laserlys.
Italian:
Lo scanner SHUTTLECè conforme alle norme di sicurezza IEC 825-1 (1993) relative ad un prodotto
laser di Classe 1. È inoltre conforme alla norma U.S. 21CFR1040 relativa ad un prodotto laser di
Classe IIa. Evitare l'esposizione prolungata all'emissione diretta di luce laser.
Portuguese:
O scanner SHUTTLECestá conforme as normas de segurança IEC 825-1 (1993) para a Classe 1 dos
produtos laser. Também está conforme a norma U.S. 21CFR1040 aplicada nos produtos laser da
Classe IIa. Evite expor os olhos directa e prolongadamente aos raios laser.

Scantech-ID ShuttleCSG-15Colour 7
Spanish:
El scanner SHUTTLEC reune las normas de seguridad IEC 825-1 (1993) para un producto laser de
Clase 1. Y también reune las normas U.S. 21CFR1040 que se aplican a un producto laser de Clase IIa.
Se debe evitar mirar muy fijo en luz lasérica directa.
English:
The SHUTTLECscanner complies with safety standard IEC 825-1 (1993) for a Class I laser product.
It also complies with U.S. 21CFR1040 as applicable to a Class IIa laser product.
Avoid long term viewing of direct laser light.
Optical:
The use of optical instruments with this product will increase eye hazard. Optical instruments include
binoculars, microscopes and magnifying glasses but do not include eyeglasses worn by the user.
Radiant Energy:
The SHUTTLECuses a low-power laser diode operating at 630…670 nm in an opto-mechanical scanner
resulting in less than 0.6 mW peak output power. Laser light observed at 13 cm (5.1 in.) above the
window through a 7 mm (0.28 in.) aperture and averaged over 1000 seconds is less than 3.9 µW per
CDRH Class IIa specification. Do not attempt to remove the protective housing of the scanner, as
unscanned laser light with a peak output up to 0.8 mW could be accessible inside.
Laser Light Viewer:
The scanner window is the only aperture through which laser light may be observed on this product.
A failure of the scanner motor, while the laser diode continues to emit a laser beam, may cause
emission levels to exceed those for safe operation. The scanner has safeguards to prevent this
occurrence. If, however, a stationary laser beam is emitted, the failing scanner should be disconnected
from its power source immediately.
Adjustments:
Do not attempt any adjustments to or alteration of this product. Do not remove the scanner’s
protective housing. There are no user-serviceable parts inside.
CAUTION
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous laser light
exposure.

8 Product Safety
1.3 DECLARATIONS OF CONFORMITY

Scantech-ID ShuttleCSG-15Colour 9
Declaration of Compliance ROHS II
Company Name: Champtek Incorporated
Product Model Name: SG-15Colour
We certify the above listed product, parts, materials and packaging are in
compliance with the European Economic Union (EEU) “Reduction of Hazardous
Substances” (RoHS II) Directive 2011/65/EU, except for the exemptions listed
under RoHS II.
Pertaining to the design/manufacture of the above product, the following
substances are not added or used beyond acceptable levels:
1. Polybrominated Diphenyl Ethers (PBDE, including DecaBDE)
2. Polybrominateci Biphenyls (PBB)
3. Lead
4. Mercury
5. Cadmium
6. Hexavalent Chromium.
The above product is in compliance with the (RoHS II) Directive 2011/65/EU
by July 1, 2011.
Signature
Allen Wang,
Quality Manager
July 2016

10 Product Safety
1.4 PRODUCT LABELLING
LAN Console DC
Scantech-ID BV
Heliumweg 34 A
3812 RE Amersfoort
The Netherlands

Chapter 2 General Description

12 General Description
2.1 USE OF THE SHUTTLEC
The ShuttleCis a Price Checker, which provides the user with the opportunity to
scan their chosen product and display product information or verify the price
before getting to the checkout. Apart from this, the ShuttleCoffers the ability to
interface with loyalty cards, display special offers, display dual currency, etc.
Moreover, store level profitability can be increased.
Apart from the use as an advanced price checker, the ShuttleCcan also be used in
many other environments where identification and information is required. This
includes use with ticketing, access control, time check, route and place guidance
and item check in a warehouse or stockroom.

Scantech-ID ShuttleCSG-15Colour 13
2.2 CONSTRUCTION OF THE SHUTTLECSG-15COLOUR
The various parts of the ShuttleCare indicated in figure 2.1:
A. Front housing with window
B. Colour TFT-LCD
Display size is 320X240 pixels QVGA 70 X 53 mm
Color Depth 16.7M Colours
C. Back Housing
D. Scantech-ID omni-directional scanner, 2D Imager or CCD single line scanner
E. Main board
F. Back Cover.
Fig 2.1
A
B
C
D
F
E

14 General Description
2.3 FUNCTIONING OF THE SHUTTLECSG-15COLOUR
2.3.1 Introduction
The ShuttleCis an information terminal, which receives input (barcode), from a
user and answers via the display. The display contents is provided by a computer
application, which runs on a (server) system elsewhere.
2.3.2 Input
The main input -bar code information- is generated by the integrated Scantech
barcode reader, which is characterised by a high performance 24 scan line
omni-directional laser scan pattern, or by a CCD single line scanner.
2.3.3 Output
Based on the bar code input and the application software on the host-system the
ShuttleCcommunicates with the user via text on the screen and optional graphics
and audio feedback via the speaker.

Scantech-ID ShuttleCSG-15Colour 15
2.3.4 Software & Control
The functions during daily use of the ShuttleCare determined by the application
program, which is controlling the ShuttleC. So the task of the storage of
databases, providing the information and sending it to the display of the ShuttleC
will be performed by a central host system.
Providing this application, running on the host system, is the responsibility of the
System Integrator.
Barcode Database Barcode
Product and
graphical info Product
info
Host
Application
(by System
Integrator)
The SG-15Colour sends barcodes to the host, according to the following table:
CODE MESSAGE FORMAT
EAN-13 F D1D2D3D4D5D6D7D8D9D10 D11 D12 D13 [CR]
EAN-8 FF D1D2D3D4D5D6D7D8[CR]
UPC-A A D1D2D3D4D5D6D7D8D9D10 D11 D12 [CR]
UPC-E E Ø D1D2D3D4D5D6[CR]
ITF i D1- Dx [CR]
Code 39 * D1- Dx [CR]
Code 32 * D1- Dx [CR]
Codabar % D1- Dx [CR]
Code128 # D1- Dx [CR]
EAN-128 P ]C1 D1- Dx [CR]
DataBar R D1- Dx [CR]
The ShuttleCdocumentation and the demo/set-up programs provide you with
all the required information on how to communicate with the ShuttleCand how
to control it. The SG-15Colour Product Support Library contains all kind of source
code examples and a complete example for application software (incl. free source
code), including an Ethernet driver to enable the integrator to get the SG-15Colour
up and running in no time.
ShuttleC