SCHURTER 4783 Series User manual

1. Wiring for 4783
Torque Value 0.8 Nm
35
N blue
yellow / green
L brown
Cable Guard
Cable Clamp
Torque Value 0.5 Nm
Torque Value 0.3 Nm
IEC UL
Cable Type H05VV-F SVT, SJT
CableDiameter min Ø 7.6mm Ø 7.7mm
CableDiameter max Ø 9.4mm Ø 9.5mm
Wire Size min 3x0.75mm² 3xAWG18 (0.82mm²)
Wire Size max 3x1.50mm² 3xAWG14 (2.08mm²)
Reversible Cable Clamp
For small
Cable diameters
For large
Cable diameters
L
PE
N
LINE
L
PE
N
LOAD
1. Wiring for 4783
Torque Value 0.8 Nm
35
N blue
yellow / green
L brown
Cable Guard
Cable Clamp
Torque Value 0.5 Nm
Torque Value 0.3 Nm
IEC UL
Cable Type H05VV-F SVT, SJT
CableDiameter min Ø 7.6mm Ø 7.7mm
CableDiameter max Ø 9.4mm Ø 9.5mm
Wire Size min 3x0.75mm² 3xAWG18 (0.82mm²)
Wire Size max 3x1.50mm² 3xAWG14 (2.08mm²)
Reversible Cable Clamp
For small
Cable diameters
For large
Cable diameters
L
PE
N
LINE
L
PE
N
LOAD
owner
huberth creation date 29.07.2019 release date 29.07.2019 released by huberth change order no 2018100 rev Bpage 1 of 2 D10-024-540
Operation Manual Wiring for 4783

2. Assembly Instruction
Disconnect power before wiring!
Keep removed piece parts at a safe place to have them ready for reassembling.
1. Loosen cover screw and remove cover.
2. Loosen cable clamp screws and remove cable guard.
3. Insert cord into cable guard.
4. Remove outer jacket on cord 35 mm. Make sure not to hurt insulation of single conductors.
5. Reduce the length of the “neutral” and “line” wire to 30 mm.
6. Strip the insulation from the wires at a length of 7 mm.
7. Loosen terminal screws but do not remove screws.
8. Connect green or green/yellow (ground) wire to center clamp marked with ground symbol.
9. Connect blue (white or light grey) wire to clamp marked „N“ (neutral).
10. Connect brown (black / “hot”) wire to clamp marked „L“ (line).
11. Tighten all wire clamp screws with a torque of 0.5 Nm.
12. Insert shoulder of cable guard into cutout of base unit.
13. Assemble cable clamp over cut-off end of outer jacket of the cord and tighten cable clamp screws with a
torque of 0.3Nm. (Turn the cable clamp for small cable diameters)
14. Assemble cover unit and tighten cover screw with a torque of 0.8 Nm.
Warning:
Failure to wire as instructed may cause personal injury or damage to device or equipment.
To be installed or checked by an qualified person only.
For factory assembly only.
2. Assembly Instruction
Disconnect power before wiring!
Keep removed piece parts at a safe place to have them ready for reassembling.
1. Loosen cover screw and remove cover.
2. Loosen cable clamp screws and remove cable guard.
3. Insert cord into cable guard.
4. Remove outer jacket on cord 35 mm. Make sure not to hurt insulation of single conductors.
5. Reduce the length of the “neutral” and “line” wire to 30 mm.
6. Strip the insulation from the wires at a length of 7 mm.
7. Loosen terminal screws but do not remove screws.
8. Connect green or green/yellow (ground) wire to center clamp marked with ground symbol.
9. Connect blue (white or light grey) wire to clamp marked „N“ (neutral).
10. Connect brown (black / “hot”) wire to clamp marked „L“ (line).
11. Tighten all wire clamp screws with a torque of 0.5 Nm.
12. Insert shoulder of cable guard into cutout of base unit.
13. Assemble cable clamp over cut-off end of outer jacket of the cord and tighten cable clamp screws with a
torque of 0.3Nm. (Turn the cable clamp for small cable diameters)
14. Assemble cover unit and tighten cover screw with a torque of 0.8 Nm.
Warning:
Failure to wire as instructed may cause personal injury or damage to device or equipment.
To be installed or checked by an qualified person only.
For factory assembly only.
owner
huberth creation date 29.07.2019 release date 29.07.2019 released by huberth change order no 2018100 rev Bpage 2 of 2 D10-024-540
Operation Manual Wiring for 4783