SCHURTER 9009 User manual

1. Wiring for 9009
25
7
25
7
25
Cable Clamp
(turn for Ø > 6.8 mm)
L brown
Yellow / green
N blue
Torque Value
0.8Nm
9009-01XX-XX: Cut
for cables over Ø
8.5 mm
Cable guard
Torque Value
0.8Nm
Torque Value
0.4Nm
7
Cable end sleeves
(Optional, not enclosed)
IN OUT
LL’
PE PE’
NN’
Applicable Cable Types
IEC
Type
Cable Type1)
Wire Size
Cable Ø
min.2)
max.
max.
9009
H05VV-F 3G
3x 1.00mm2
3x 1.50mm2
10.0mm
H05RR-F 3G
3x 1.00mm2
3x 1.00mm2
10.0mm
UL
Type
Cable Type3)
Wire Size
Cable Ø
min.
max.
max.
9009
SV…
3x AWG18
3x AWG16
10.0mm
SJ…
3x AWG18
3x AWG14
10.0mm
1) Harmonized wire coding in accordance with IEC60227-5 respectively IEC60245-4.
2) If cord has a length exceeding 2m, nominal cross-sectional areas shall be 1.0mm2/16AWG or more.
3) Types according to UL 62 which begins with the given letters (i.e. SV… includes SV, SVT, SVE etc.).
1. Wiring for 9009
25
7
25
7
25
Cable Clamp
(turn for Ø > 6.8 mm)
L brown
Yellow / green
N blue
Torque Value
0.8Nm
9009-01XX-XX: Cut
for cables over Ø
8.5 mm
Cable guard
Torque Value
0.8Nm
Torque Value
0.4Nm
7
Cable end sleeves
(Optional, not enclosed)
IN OUT
LL’
PE PE’
NN’
Applicable Cable Types
IEC
Type
Cable Type1)
Wire Size
Cable Ø
min.2)
max.
max.
9009
H05VV-F 3G
3x 1.00mm2
3x 1.50mm2
10.0mm
H05RR-F 3G
3x 1.00mm2
3x 1.00mm2
10.0mm
UL
Type
Cable Type3)
Wire Size
Cable Ø
min.
max.
max.
9009
SV…
3x AWG18
3x AWG16
10.0mm
SJ…
3x AWG18
3x AWG14
10.0mm
1) Harmonized wire coding in accordance with IEC60227-5 respectively IEC60245-4.
2) If cord has a length exceeding 2m, nominal cross-sectional areas shall be 1.0mm2/16AWG or more.
3) Types according to UL 62 which begins with the given letters (i.e. SV… includes SV, SVT, SVE etc.).
owner
vettersa creation date 06.12.2017 release date 09.08.2019 released by vettersa change order no 2013669 rev Gpage 1 of 2 0115.0059
Operation Manual Wiring for 9009

2. Assembly Instruction
Disconnect power before wiring.
Keep removed piece parts at a safe place to have them ready for reassembling.
1. Loosen cover screw and remove cover.
2. Loosen cable clamp screws and remove cable guard.
3. Insert cord into PVC-cable guard.
4. Remove outer jacket on cord 25 mm. Make sure not to hurt insulation of single conductors.
5. Strip bare each copper conductor 7 mm and crimp on multicore cable ends. Do not strip more than 7 mm.
6. Loosen terminal screws but do not remove screws.
For connecting wires to terminals insert bare ends of conductors from left side of terminal screw according to
figure below. Make sure that no copper strands splice off when connecting conductors to clamps.
correct wrong
P O
P
L / N PE
7. Connect green or green/yellow (ground) wire to centre clamp marked with ground symbol.
8. Connect blue (white or light grey) wire to clamp marked „N“ (neutral).
9. Connect brown (black / “hot”) wire to clamp marked „L“ (line).
10. Tighten all wire clamp screws with a torque of 0,8 Nm.
11. Insert shoulder of PVC-cable guard into cut-out of base unit.
12. Assemble cable clamp over cut-off end of outer jacket of the cord and tighten cable clamp screws with a
torque of 0,8 Nm.
13. Assemble cover unit and tighten cover screw with a torque of 0,4 Nm.
Warning: Failure to wire as instructed may cause personal injury or damage to device or equipment.
To be installed or checked by an qualified person only.
For factory assembly only.
2. Assembly Instruction
Disconnect power before wiring.
Keep removed piece parts at a safe place to have them ready for reassembling.
1. Loosen cover screw and remove cover.
2. Loosen cable clamp screws and remove cable guard.
3. Insert cord into PVC-cable guard.
4. Remove outer jacket on cord 25 mm. Make sure not to hurt insulation of single conductors.
5. Strip bare each copper conductor 7 mm and crimp on multicore cable ends. Do not strip more than 7 mm.
6. Loosen terminal screws but do not remove screws.
For connecting wires to terminals insert bare ends of conductors from left side of terminal screw according to
figure below. Make sure that no copper strands splice off when connecting conductors to clamps.
correct wrong
P O
P
L / N PE
7. Connect green or green/yellow (ground) wire to centre clamp marked with ground symbol.
8. Connect blue (white or light grey) wire to clamp marked „N“ (neutral).
9. Connect brown (black / “hot”) wire to clamp marked „L“ (line).
10. Tighten all wire clamp screws with a torque of 0,8 Nm.
11. Insert shoulder of PVC-cable guard into cut-out of base unit.
12. Assemble cable clamp over cut-off end of outer jacket of the cord and tighten cable clamp screws with a
torque of 0,8 Nm.
13. Assemble cover unit and tighten cover screw with a torque of 0,4 Nm.
Warning: Failure to wire as instructed may cause personal injury or damage to device or equipment.
To be installed or checked by an qualified person only.
For factory assembly only.
owner
vettersa creation date 06.12.2017 release date 09.08.2019 released by vettersa change order no 2013669 rev Gpage 2 of 2 0115.0059
Operation Manual Wiring for 9009