Scientech Astral series User manual

PN 11869C 1

ASTRAL Series

Power Meter &

Calorimeters

Laser Power

Measurement

Operating Manual

Thank you for choosing a Scientech Astral calorimeter. Scientech’s employees are pleased to provide

you with a product designed for years of reliable and accurate service. Please read this operating manual

before using your detector and power meter. This reference information will allow you to fully

understand the capabilities of the product. The detector is intended to be used only in the manner

outlined in this manual. Operation not within specifications for the product may cause product damage.

PN 11869C 2 
 
Table of Contents 
 
Calorimeter Operating Parameters.....................................................................................................................3 
Environmental Requirements ...........................................................................................................................4 
CE Mark Certification .............................................................................................................................4 
Unpacking....................................................................................................................................................4 
Adapter/Battery.............................................................................................................................................4 
Astral™ Series Detector specifications...............................................................................................................4 
Astral™ AI310 Power Meter Specifications ........................................................................................................9 
Changing or Installing Batteries........................................................................................................................9 
Using AI310 Power Meter with Astral Calorimeter.............................................................................................11 
A. Joules Mode......................................................................................................................13 
B. Watts Mode:......................................................................................................................14 
Scientech Calibration Service.........................................................................................................................16 
Limited Warranty.........................................................................................................................................16 
Return Material Procedure.............................................................................................................................17 
Disposal of Electronic Equipment ...................................................................................................................17 
 
 
 
 
 
 
 
 

PN 11869C 3

CALORIMETER OPERATING PARAMETERS

AI310 Serial Number___________________

Calorimeter 1: Calorimeter 2:

Model No:

Serial No:

Model No:

Serial No:

Calibration Wavelength nm Calibration Wavelength: nm

Output Sensitivity (S):

Time Constant (1/e):

Calibration Temp:

V/W Output Sensitivity (S): V/W

sec. Time Constant (1/e): sec.

oC Calibration Temp: °C

Sub. Heater Resistance (Rc): ohms Sub. Heater Resistance (Rc): ohms

Sub. Heater Voltage (Vh): volts Sub. Heater Voltage (Vh): volts

Sub. Heater Wattage (Wh) watts Sub. Heater Wattage (Wh): watts

PN 11869C 4

ENVIRONMENTAL REQUIREMENTS

This product is intended for indoor use at altitudes up to 2000 meters, Pollution Degree 2 in accordance

with IEC 664 and transient over voltages according to Installation Categories (Overvoltage Categories)

II.

CE Mark Certification

The Astral Series calorimeters listed in this manual have been certified for the European CE mark.

UNPACKING

The meter, calorimeter, and accessories are shipped in custom packing materials. All packing materials

should be saved for future damage free shipments for calibration or repair.

ADAPTER/BATTERY

When using the Scientech supplied AC adapter/charger, the AI310 will operate with or without the

optional battery installed. However, if the battery is installed, it must have a minimum charge of

approximately 1 hour before the AI310 will operate on battery power alone.

The AI310 can be used with the optional rechargeable battery (part number 11640), which provides

approximately 6 hours of usage before requiring recharging. To recharge the batteries, connect the

charger to the power meter and the appropriate electrical outlet. Allow 1 to 3 hours for a full charge.

Whenever the AC adapter is connected to both the AI310 and wall outlet, the battery is being charged.

The AI310 can be powered by battery or wall plug power supply (or USB interface). If the battery is

installed, it is charged whenever wall plug power (or USB power) is present. When running from wall

plug, with optional battery installed, the battery annunciator in the LCD display will be on when the

battery is being charged and off when the battery is fully charged. This annunciator may also be on

when there is no battery installed. When operating on battery power alone, the annunciator will be off.

When the battery approaches its end of charge, the annunciator will flash at a 1Hz rate for about two

minutes. Then the annunciator will flash at a higher rate (2Hz) letting you know that in about another

two minutes the AI310 will cease to function. In this event you should turn the power rocker switch to

the OFF position, plug in the AC adapter, and turn the power rocker switch to ON. The AI310 will start

in the normal way and the battery annunciator should be on indicating that the battery is being charged.

ASTRAL™SERIES DETECTOR SPECIFICATIONS

This series consists of a handheld meter and a selection of thermal detectors. Astral™series detectors

all have memory integrated into the detectors, used to store calibration constants as well as other data

such as integration time and date. Plug an Astral™detector into the meter, and it’s ready for use.

Without storing calibration data with the detector, you will need to manually enter the calibration data

into the detector via the power meter. Also, if you were using multiple detectors with a single meter,

then having calibration data in the detector also prevents errors if somebody forgets to input the

detector’s calibration data into the meter.

The Astral Series detectors are available in either surface or volume absorbing models with apertures of

custom sizes or standard 8mm, 16mm, 25mm, 50mm, 100mm, and 200mm aperture models. The surface

absorbing models are ideal for measuring continuous wave lasers while the volume absorbing models

are well suited for pulsed lasers using either the watts mode or single pulse energy mode.

Table 1. Astral™Series 8 & 25mm Calorimeter Specifications

Model

AC2500S

AC25FXS

ACX25FXS

AC2501S

ACX2501S

AC25UVS

AC2504S

Type of Absorber

Surface

Volume

Aperture Diameter

25.4 mm

8 mm

25.4 mm

8 mm

25.4 mm

Spectral Response

.25-35 µm

.193-26 µm

.4-2 µm

.266-1.2

µm

.4-1.2 µm

.193-.36

µm

.85-4.2 µm

Max Average Power

10 W

Min Average Power

1 mW when installed with Isoperibol Enclosure

Noise Level

10 µW or µJ

Max Power Density

200 W/cm²

6KW/cm2

48KW/cm2

Note 1

Note 2

Note 3

Note 4

Max Peak Power Density

1 MW/cm²

Note 15

Note 16

Note 5

8.5

GW/cm²

Note 6

Note 7

Max Single Pulse Energy

30 J

Max Energy Density

Note 8

Note 9

Note 10

Note 11

Note 12

Note 13

Note 14

Precision

< 1 %

Accuracy

± 3 %

Dimensions DxL

inches

3.75 x 2.2

9.53 x 5.6

3.75 x 2.2

9.53 x 5.6

3.75 x 3.82

9.53 x 9.7

3.75 x 2.2

9.53 x 5.6

3.75 x 3.82

9.53 x 9.7

3.75 x 2.2

9.53 x 5.6

3.75 x 2.2

9.53 x 5.6

Weight - pounds/kg

1.5/0.68

1.7/0.77

1.5/0.68

1.7/0.77

1.5/0.68

Table 2. Astral™Series 16 & 50mm Calorimeter Specifications

Model

AC5000S

AC50FXS

ACX50FXS

AC5001S

ACX5001S

AC50UVS

AC5004S

Type Absorber

Surface

Volume

Aperture Diameter

50.8 mm

16 mm

50.8 mm

16 mm

50.8 mm

Spectral Response

.25-35 µm

.193-26

µm

.4-2 µm

.266-1.2

µm

.4-1.2 µm

.193-.36 µm

.85-4.2

µm

Max Average Power

30 W

Min Average Power

40 mW

Noise Level

400 μW or μJ

Max Power Density

200 W/cm²

6 kW/cm²

48 kW/cm²

Note 1

Note 2

Note 3

Note 4

Max Peak Power

Density

1 MW/cm²

Note 15

Note 16

Note 5

8.5 GW/cm²

Note 6

Note 7

Max Single Pulse

Energy

100 J

Max Energy Density

Note 8

Note 9

Note 10

Note 11

Note 12

Note 13

Note 14

Precision

< 1 %

Accuracy

± 3 %

Dimensions DxL

inches

4.75 x 2.3

12.07 x 5.8

4.75 x 2.3

12.07 x 5.8

4.75 x 3.92

12.07 x 9.96

4.75 x 2.3

12.07 x 5.8

4.75 x 3.92

12.07 x 9.96

4.75 x 2.3

12.07x 5.8

4.75 x 2.3

12.07x5.8

Weight pounds/kgs

2.9/1.3

3.1/1.4

2.9/1.3

3.1/1.4

2.9/1.3

Notes for 8, 25, 16, & 50mm Calorimeters:

Note 1:

AC2501S, AC5001S

30W/cm2@ 1064nm

23W/cm2@ 532nm

8.5W/cm2@ 355nm

175mW/cm2@ 266nm

Note 2:

ACX2501S, ACX5001S

Note 1 specs x 8 for 400nm to 1.2μm

Note 3:

AC25UVS, AC50UVS

50W/cm2@ 355nm

Note 4:

AC2504S, AC5004S

35W/cm2@1064nm

Note 5:

AC2501S, AC5001S

100GW/cm2@ 1064nm

78GW/cm2@532nm

29GW/cm2@ 355nm

580MW/cm2@266nm

Note 6:

AC25UVS, AC50UVS

Repetitive pulses:

101MW/cm2@ 355nm

Single pulses:

3.5GW/cm2 @ 355nm

Note 7:

AC2504S, AC5004S

125GW/cm2@ 1064nm

Note 8:

AC2500S, AC5000S

Max J/cm2= 1,000 x (pulse width)1/2 to a maximum of 200J/cm2

Note 9:

AC25FXS, AC50FXS

Max J/cm2= 4,950 x (pulse width)1/2 to a maximum of 12.3J/cm2.

Note 10:

ACX25FXS, ACX50FXS

Max J/cm2= 39,600 x (pulse width)1/2 to a maximum of 36.9J/cm2.

Note 11:

AC2501S, AC5001S

Repetitive pulses:

4.1J/cm2@1064nm

3.2J/cm2@532nm

1.2J/cm2@355nm

24mJ/cm2@266nm

Single pulses:

8J/cm2@1064nm

6.2J/cm2@532nm

2.3J/cm2@355nm

46mJ/cm2@266nm

Note 12:

ACX2501S, ACX5001S

Note 11 specs x 8 for 400nm to 1.2μm

Note 13:

AC25UVS, AC50UVS

Repetitive pulses: 1.1J/cm2@ 355nm

Single pulses: 40J/cm2 @ 355nm

Note 14:

AC2504S, AC5004S

Repetitive pulses: 4.8J/cm2@ 1064nm

Single pulses: 10J/cm2 @ 1064nm

Note 15:

AC25FXS, AC50FXS

Max p.p.d.: 70MW/cm2@1064nm pulse

Note 16:

ACX25FXS, ACX50FXS

Max p.p.d.: 560MW/cm2@1064nm pulse

Table 3. Astral™Series 100mm Calorimeter Specifications

Model

360401S

380401S

380402S

384UV5S

Type of Absorber

Surface

Volume

Aperture Diameter

100mm

Minimum Beam Diameter

5cm

Spectral Response

.25 - 35μm

.266 - 1.2µm

9 -11µm

.193 - .36μm

Max Average Power

50W with full illumination of absorbing surface

Min Average Power

150mW

Noise Level

1.5mJ - mW

Max Power Density

200W/cm²

See Note 1

4W/cm²

Note 2

Max Peak Power Density

1MW/cm²

See Note 4

100MW/cm²

See Note 5

Max Single Pulse Energy

300J

Max Energy Density

Note 7

Note 8

4J/cm2

Note 9

Precision

< 1%

Accuracy

Dimensions DxL

inches

6.00 x 8.00

15.24 x 20.32

Weight

pounds

kgs

2.72

Table 4. Astral™Series 200mm Calorimeter Specifications

Model

360801S

380801S

380802S

384UV5S

Type of Absorber

Surface

Volume*

Volume

Aperture Diameter

200mm

Minimum Beam Diameter

7.5cm

Spectral Response

.25 - 35μm

.266 - 1.2µm

9 -11µm

.193 - .36μm

Max Average Power

100W with full illumination of absorbing surface

Min Average Power

700mW

Noise Level

7mJ or 7 mW

Max Power Density

200W/cm²

See Note 3

4W/cm²

Note 2

Max Peak Power Density

1MW/cm²

See Note 6

100MW/cm²

See Note 5

Max Single Pulse Energy

1000J

500J

1000J

Max Energy Density

Note 7

Note 10

4J/cm2

Note 9

Precision

< 1%

Accuracy

Dimensions DxL

inches

9.00 x 10.00

22.86 x 25.40

Weight

pounds

kgs

16.27

7.26

Notes for Astral Series 100 & 200mm Calorimeters:

Note 1:

380401S

27W/cm2@ 1064 nm

21W/cm2 @ 532 nm

7.7W/cm2@ 355 nm

158mW/cm2@ 266nm

Note 2:

384UV5S, 388UV5S

50W/cm2@ 355nm

Note 3:

380801S

13.5W/cm2@ 1064 nm

10.5W/cm2@ 532 nm

3.85W/cm2@ 355 nm

79mW/cm2@ 266nm

Note 4:

380401S

90GW/cm2@ 1064 nm

71GW/cm2@ 532 nm

27GW/cm2@ 355 nm

530MW/cm2@ 266nm

Note 5:

384UV5S, 388UV5S

Repetitive pulses:

101MW/cm2@ 355nm

Single pulses:

3.5GW/cm2@ 355nm

Note 6:

380801S

45GW/cm2@ 1064 nm

35.5GW/cm2@ 532 nm

13.5GW/cm2@ 355 nm

265MW/cm2@ 266nm

Note 7:

360401S, 360801S

Max J/cm2 = 1000 x (pulse width)1/2 to a maximum of 200J/cm2

Note 8:

380401S

Repetitive pulses:

3.7J/cm2@ 1064nm

2.9J/cm2@ 532nm

1J/cm2@ 355nm

20mJ/cm2@ 266nm

Single pulses:

7J/cm2@ 1064nm

5.6J/cm2@ 532nm

2.1J/cm2@ 355nm

41mJ/cm2@ 266nm

Note 9:

384UV5S, 388UV5S

Repetitive pulses:

1.1J/cm2@ 355nm

Single pulses:

40J/cm2 @ 355nm

Note 10:

38-0801S

Repetitive pulses:

1.85J/cm2@ 1064nm

1.45J/cm2@ 532nm

0.5J/cm2@ 355nm

10mJ/cm2@ 266nm

ASTRAL™AI310 POWER METER SPECIFICATIONS

The Models AI310 and AI310D are identical to each other in every respect except the analog meter.

The AI310 has both an analog and digital display. The AI310D has only a digital readout. All

references to the AI310 are intended to include the AI310D except where noted. Also, the words

"indicator" and "meter" are synonymous.

Table 5. Astral™Power Meter Specifications

Model

AI310D-USBL

AI310D

AI310

Display

4 Digit LCD

4 Digit LCD with selectable

analog indicator

Modes, Power or Energy

Watts or Joules

Full Scale Ranges, with 25mm

Astral Calorimeter

100.0 mW, 1.000 W, 10.00

W, 300.0 mJ, 3.000 J, 30.00 J

100.0 mW, 1.000 W, 10.00 W,

300.0 mJ, 3.000 J, 30.00 J

100.0 mW, 1.000 W, 10.00 W,

300.0 mJ, 3.000 J, 30.00 J

Full Scale Ranges, with 50mm

Astral Calorimeter

3.000 W, 30.00 W, 1.000 J,

10.00 J, 100.0 J

3.000 W, 30.00 W, 1.000 J,

10.00 J, 100.0 J

3.000 W, 30.00 W, 1.000 J,

10.00 J, 100.0 J

Full Scale Ranges, with 100mm

Astral Calorimeter

50.00 W, 30.00 J, 300.0 J

Full Scale Ranges, with 200mm

Astral Calorimeter

100.00 W, 100.00 J, 1,000.0 J

Operating Temperature

5 oC to 40 oC

Power Requirements

100-240Vac 50-60Hz,

0.6Amps

100-240Vac 50-60Hz,

0.6Amps

100-240Vac 50-60Hz, 0.6Amps

Battery, Scientech Part No. 11640

Lithium Poly included

Battery Operation Time

~6 hrs

Ports

power, detector RS232, USB

power, detector RS232

Stand for Meter, Part No. MT

Optional

Dimensions D x L

Inches

6.3 x 4.2 x 1.5

16.0 x 10.7 x 3.8

6.3 x 4.2 x 1.5

16.0 x 10.7 x 3.8

6.3 x 4.2 x 1.5

16.0 x 10.7 x 3.8

Weight

Pounds

kilograms

1.0

0.45

1.0

0.45

1.0

0.45

CHANGING OR INSTALLING BATTERIES

Use only batteries equivalent to Scientech part number 11640 replacement battery. This battery is

provided with a protection circuit designed to protect the cell. Misuse or mistreatment of the battery can

result in gas generation, leakage or fire. The use of any other battery in the AI310 will void the product

warranty.

Note: Dispose of used batteries according to local regulations.

To install batteries, proceed as follows:

1. Remove the 2 screws holding the top panel to the case (see Figure 1)

2. Slide the front panel assembly out of the case.

3. Install the new battery to inside bottom of the case using double sided tape provided.

4. Replace front panel assembly and screws. Then charge the battery for 1 to 3 hours.

CAREFULLY START PCA ASSEMBLY

SLIDING INTO THE CASE. CONNECT

BATTERY AND FINISH SLIDEING THE

PCA ASSEMBLY IN THE CASE.ATTACH

BEZELS AND COVERS TO CASE USING

SCREWS PROVIDED. TIGHTEN.

INSTALL STANDOFFS TO CONNECTOR.

ATTACH OPTIONAL BATTERY TO

BOTTOM OF CASE WITH TAPE IN THE

LOCATION SHOWN.

BATTERY CONNECTOR ON

PC BOARD BACK SIDE

HERE.

Figure 1. Battery Replacement

Figure 2. Astral AI310 Power Meter with 25mm Calorimeter

USING AI310 POWER METER WITH ASTRAL CALORIMETER

1. Turn On the Meter Power

Toggle the ON/OFF rocker switch, located on the top of the AI310, to the ON position. The power

meter will immediately turn on with all LCD segments briefly, and then revert to the operational state

last used. The AI310 will check for the presence of the sensor, and if the sensor is absent, the display

will read “nodF” and the AI310 will continue checking every 15 seconds for 2 minutes. If, after the 2

minutes have elapsed, the sensor is still not found, then the AI310 will power itself down to a “sleep”

mode, displaying “SLEP” in the LCD. If a sensor is subsequently plugged into the AI310, you must

push any front panel button to awaken the AI310 and continue in normal operating mode.

If the AI310 is running from battery power, and if no button has been pressed or if power the reading is

below 1% of full-scale for a period of time set by the user (as described in the timeout instructions

below), The AI310 will also power itself down to a “sleep” mode, displaying “SLEP” in the LCD. To

USB port

(on some models)

Analog Meter

Zero Adjust

Power on/off

Switch

AC Power

Port

Astral Detector

Port

Astral Calorimeter

with Fiber Holder

Detector Post, Holder &

Base Mount (sold

separately)

Astral

Connector

recover from this dormant mode, push any front panel button to awaken the AI310 and continue in

normal operating mode.

The operating parameters of the SERIES S CALORIMETER are automatically loaded into the AI310

through the calorimeter’s intelligent connector. In normal operating mode the AI310 checks for a sensor

every 15 seconds allowing for hot swapping of sensors with no user intervention required.

2. Connect the Calorimeter

A 3-meter cable with an intelligent connector is hard wired to the Astral Calorimeter. Plug the

detector’s cable into the mating connector on the AI310.

Each detector has a 1/2" diameter mounting hole for installing the detector onto a mounting base

assembly. Screw the mounting base post into one of the mounting holes in the body of the calorimeter.

Optional mounting base assemblies are available for purchase from Scientech for mounting the

detector/mounting base assembly to an optical bench.

3. Zero Button

Pressing the ZERO button will zero the display.

4. Zero the Analog Needle (does not apply to the AI310D)

Refer to Figure 3. The black slotted button located just below the display allows screwdriver adjustment

to set the analog needle to zero. The needle adjustment should be adjusted to zero before connecting the

detector.

5. Turn the Analog Needle On or Off (does not apply to the AI310D)

To turn the analog meter on or off, press and keep holding down the RANGE button. Then release the

button after the meter scale appears or disappears. The analog meter scale will follow the selected range.

6. Select a Range

Available Ranges for 25mm Calorimeters

100.0 mW, 1.000 W, 10.00 W

300.0 mJ, 3.000 J, 30.00 J

Available Ranges for 50mm Calorimeters

3.000 W, 30.00 W

1.000 J, 10.00 J, 100.0 J

Available Ranges for 100mm Calorimeters

50.00 W

30.00 J, 300.0 J

Available Ranges for 200mm Calorimeters

100.0 W

100.0 J, 1000 J

Measurements made below 10% of full scale will exceed the absolute accuracy specification. Select a

lower range to avoid errors.

Figure 3. AI310 Display

7. Select a Mode

Pressing the MODE button toggles between Watts and Joules mode.

8. Take your measurement

Direct the laser beam onto the absorbing surface of the detector.

A. Joules Mode: Press the ZERO button to zero the display. Fire your laser. The display will show

the energy of the pulse, this may take several seconds depending on the model of the calorimeter.

The TRIG annunciator will remain lit until the calorimeter has recovered and is ready for the

next pulse. You should not fire at the calorimeter again until TRIG has gone out. When you

press the ZERO button the display reading is indicative of the thermal state of the calorimeter. If

you observe a drifting of the display you should wait until the calorimeter has come to

equilibrium before pulsing again.

Range

Mode

Joules

Trigger

B. Watts Mode: Pressing ZERO will zero the power meter, begin lasing.

9. System Overload indication

The LCD display will show “OL” when the allowable input power level for the range selected has been

exceeded. Exceeding the maximum specifications of the calorimeter will cause permanent damage to the

Astral Calorimeter.

10. Menu Features

To access the menu items, Press MODE and ZERO buttons simultaneously. The display will show the

first menu choice. Press the RANGE button to advance to the next menu choice. Press ZERO button to

select the menu choice. Pressing the RANGE button will increment the displayed value and pressing the

MODE button will decrement the displayed value. Menu items that are available are: Attenuation

Factor (ATTN) and Time Out (TO) and MODE (CAL).

A. Attenuation Factors

Access the Menu, as described in step 13, step through menu choices until ATTN is displayed,

then press the ZERO button to select. Use the RANGE button to increment and the MODE

button to decrement the attenuation factor. Pressing the ZERO and MODE buttons

simultaneously will return the value to 1.00 (the factory default). Press ZERO to select the

attenuation factor and return to normal operation. Very large or small attenuator values may

require re-ranging the power meter for proper operation. For example, with an attenuator value

of 10 and you apply 1 Watt of power, the display will indicate 10 Watts and must be in the 10

Watt range.

Values available are:

0.01… 0.99, 1.0,

1.1… 9.9, 10,

11 … 100

B. Time Out

The time out feature conserves battery power by putting the AI310 to sleep if there are no front panel

button pushes, after a selected period of time. To awaken the AI310 once it is in the sleep mode, press

ZERO on the front panel.

To change the time out period, access the Menu, as described in step 13, step through the menu choices

until TO is displayed, then press the ZERO button to select. Use the RANGE button to increment and

the MODE button to decrement the timeout factor. Pressing the ZERO and MODE buttons

simultaneously will return the value to 0 (the factory default). Press ZERO to select the timeout factor

and return to normal operation.

Default value is 0 or OFF.

Values available are:

0, 5, 10, 15 ... 55, 60 (minutes)

11. Pulse Recovery Time

This changes the time period allowed in making single shot energy measurements. Typically, the time it

takes to recover from a pulse is four to six times the calorimeters thermal time constant. The typical time

for each calorimeter size is given below.

Table 6. Calorimeter Pulse Recovery Time

AC25XXS

60 seconds

AC50XXS

90 seconds

360401S

105 seconds

380401S, 380402S, 384UV5S

180 seconds

360801S

135 seconds

380801S, 380802S, 88UV5S

210 seconds

To change the time, access the Menu, as described in step 13, step through the menu choices until CTO

is displayed, then press the ZERO button to select. Use the RANGE button to increment and the MODE

button to decrement the time. Pressing the ZERO and MODE buttons simultaneously will return to the

value last stored. Press ZERO to select the timeout factor and return to normal operation.

Values available are:

15 to 405 seconds in 15 second steps

12. Wall Mount Power Supply

Use the wall mount power supply to power the AI310 and charge the optional battery.

13. Optional Meter Mounting System

Scientech offers a sturdy mount system (Part Number MT) consists of a non-slip base with three

moldable feet, ball mounts, and a meter cradle. This system will hold your AI310 about 15cm above an

optical bench or work surface in an upright position. The ball mounts let you reposition your meter to

accommodate any viewing angle you desire. It also allows you to easily remove your meter at the end

of the day for safekeeping.

SCIENTECH CALIBRATION SERVICE

The Astral™AI310 power meters and calorimeters are calibrated at Scientech’s authorized service

center and the calibration constants were provided with the detector.

Scientech detectors include a NIST traceable calibration certificate, to document that you are getting the

most accurate laser measurement possible.

An optimum calibration of each detector is ensured by Scientech’s highly trained and skilled service

team. Excessive energy or peak power density can damage a detector. Safe operating limits are specified

in the detector specifications. If your calculated energy or peak power conditions exceed those specified

for the model, optical attenuation may be used as a solution.

Electric substitution heater coils are available as an option that allows customer to perform their own

field calibration. These electric heaters are only available for new detector purchases only by adding an

“H” to the end of the detector part number when placing an order.

Scientech recommends that a complete calibration be performed annually to verify system accuracy.

Please visit Scientech’s website at www.scientechinc.com to obtain an RMA (returned material

authorization) number and complete the form noting that you are requesting calibration of your detector.

You may also contact our Product Service Department at (800)525-0522 or (303)444-1361 or Fax

(303)444-9229 or email [email protected]. Be prepared to provide model number, serial number

along with contact information. to arrange for a NIST traceable, factory calibration. Scientech calibrates

the detector with its power meter for the same price.

LIMITED WARRANTY

Scientech warrants and represents that the laser power measurement product will be free from defects in

design, materials and workmanship and conform with applicable Scientech product specifications for a

period of three (3) years. The product warranty period begins on the date of shipment from Scientech.

Scientech warrants that its products shall conform to applicable Scientech specifications and drawings

and will meet all the functional and performance requirements when properly installed, operated, and

maintained in accordance with Scientech’s operating manual. Warranty does not extend to any Scientech

products that have been subjected to misuse, abuse, or accidents, or improper installation, maintenance

or applications, repaired by unauthorized personnel, or Products in which the tamper proof sticker has

been removed or broken.

During the warranty period, Scientech will repair, or at its option replace at no charge, components that

prove to be defective. The product must be returned, shipping prepaid, to Scientech's authorized repair

facility. Products repaired by Scientech’s authorized repair personnel/facilities will be warranted against

defects in the repaired component and workmanship for a period of 365 days from the date of shipment

of the repaired Product.

RETURN MATERIAL PROCEDURE

Should it become necessary to return any product to Scientech for any reason including calibration,

please visit Scientech’s website at www.scientechinc.com to obtain an RMA (returned material

authorization) number and complete the form. You may also contact our Product Service Department at

(800)525-0522 or (303)444-1361 or Fax (303)444-9229 or email [email protected]. Be prepared to

provide model number, serial number, and a description of the problem along with contact information.

Frequently we can provide self-help information which will eliminate the need for returning the product.

If product return is required, please pack the items in the original box and packing material. As an

alternate, place the equipment in a snug-fitting box, and then pack that box in a larger box with at least

four inches of packing material. Scientech does not assume responsibility for products damaged during

shipping and shipping damage will not be treated as a warranty repair. Please include a point of contact,

email address, and phone number of the person we should contact regarding repair questions.

Normally, products are repaired and shipped within five (5) business days following receipt of the

product at the authorized service facility. The repair turn-around time could vary depending on the

workload.

Shipping Address: Scientech, Inc.

Product Service Department

5649 Arapahoe Ave.

Boulder, Colorado 80303 U.S.A.

DISPOSAL OF ELECTRONIC EQUIPMENT

Scientech recommends the following for disposal of electrical and electronic equipment:

1. The best option is to reuse the equipment in its entirety.

2. Where the equipment cannot be reused in its entirety, priority should be given to reuse

of its subassemblies and components.

3. Where reuse is not appropriate, electrical and electronic equipment, including batteries,

should be recycled according to local ordinances.

4. Waste electrical and electronic equipment should never be mixed with municipal waste.

This manual suits for next models

Table of contents

Other ScienTECH Measuring Instrument manuals

ScienTECH

ScienTECH AC2500 Manual

ScienTECH

ScienTECH CS750 User manual

ScienTECH

ScienTECH Vector S200 Manual

ScienTECH

ScienTECH AB65 User manual

ScienTECH

ScienTECH Vector Series User manual

ScienTECH

ScienTECH Vector S310 Manual

ScienTECH

ScienTECH Vector Series User manual

ScienTECH

ScienTECH 380401 Manual

ScienTECH

ScienTECH 730 User manual

ScienTECH

ScienTECH NTEP User manual

Popular Measuring Instrument manuals by other brands

AFRISO

AFRISO DIT 10 operating instructions

Honeywell

Honeywell enCore Series manual

Enlogic

Enlogic Advantage Series user manual

Dostmann Electronic

Dostmann Electronic HumidCheck Instructions for use

janitza

janitza UMG 605 operating manual

Sequid

Sequid DTDR-65 Operation manual

J&D Electronics

J&D Electronics Multi-GEM 12 user guide

C-LOGIC

C-LOGIC 8730 instruction manual

Nortek

Nortek AWAC quick guide

C-LOGIC

C-LOGIC 350 instruction manual

Mid-Continent Instrument

Mid-Continent Instrument MD215 Series Installation manual and operating instructions

LaserLiner

LaserLiner SensoLite 120 quick start guide

Kobold

Kobold NUS-4x04 instruction manual

Tektronix

Tektronix KEITHLEY 4200A-SCS-PK2 quick start guide

Keysight Technologies

Keysight Technologies UXA N9040B manual

Parker

Parker SensoControl Serviceman SCM-150-1-01 Training manual

Huazheng

Huazheng HZ2831 manual

Bushnell

Bushnell 1K owner's guide

ScienTECH Astral Series User manual

Popular Measuring Instrument manuals by other brands