Scientific Atlanta AllTouch 573480 User manual

573497 Rev B 1
Any changes or modifications not expressly
approved by Scientific-Atlanta could void the
user's authority to operate this equipment.
8600Xis a trademark of Scientific-Atlanta, Inc.
AllTouch is a registered trademark of Scientific-
Atlanta, Inc.
If you wish to order additional
AllTouch®Remote Controls or an
additional user’s guide, refer to the
following table.
Item Part Number
Remote Control 573480
User’s Guide 573497 Rev B
FCC Compliance
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Note
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.These limits are designed
to provide reasonable protection against harmful
interference in a residential installation.This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communication. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
the receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
United States: Scientific-Atlanta, Inc., 4261 Communications
Drive, P.O. Box 6850, Norcross, GA 30091-6850;
Tel: [phone]; TWX: 810-799-4912; Telex: 0542898
Europe: Scientific-Atlanta Europe Ltd., Home Park Estate,
Kings Langley, Herts WD4 8LZ, England;Tel: [phone];
Fax: [phone]
Asia-Pacific: Scientific-Atlanta (HK) Ltd., Suite 56-57, 5/F New
Henry House, 10 Ice House Street, Central, Hong Kong;
Tel: [phone]; Fax: [phone]
© 1998 Scientific-Atlanta, Inc. All rights reserved. Printed in USA.
Part No. 573497 Rev B June 1998 User’s Guide
A
l
l
T
o
u
c
h
¨
VCR
1
4
7
2
5
8
0
3
6
9
AUX
V
O
L
SELECT
GUIDE
REW
PAUSE RECSTOP
PLAY FF
SET-UP BYPASS
MENU INFO
PPV
PREV. DAY NEXT DAY
MUTE
LAST
FAV
POWER
BAC
TV
CBL
C
H
AllTouch®
Remote Control

573497 Rev B
2
Contents
Introducing the AllTouch Remote Control ............................................ 3
What the buttons do ............................................................................ 4
Setting up the remote control to operate your TV................................. 6
Setting up the remote control to operate your VCR .............................. 7
Setting up the remote control to operate other devices.......................... 8
Reprogramming your cable device button ............................................ 9
All Search.......................................................................................... 10
Getting your codes............................................................................. 12
Reassigning mode buttons.................................................................. 13
Volume Lock...................................................................................... 14
Disabling/enabling channel control.................................................... 16
Programming the macro buttons........................................................ 17
Troubleshooting ................................................................................. 18
Television setup codes........................................................................ 20
VCR setup codes................................................................................ 24
TV/VCR combination setup codes...................................................... 27
CD player (Aux) setup codes............................................................. 28
Home automation (Aux) setup codes ................................................. 30
Digital cable audio (Aux) setup codes................................................ 30
Record of codes.................................................................................. 31
Reassigned mode buttons................................................................... 31
Important reminder!.......................................................................... 32

573497 Rev B 3
Introducing the AllTouch Remote Control
Your new AllTouch®Remote Control can do the job of four separate
remote controls. In fact, it can control four devices at one time. These
can be any combination of:
• Home Terminals or 8600xTM Home Communications Terminals (HCTs)
• Televisions • VCRs • Homeautomation devices
• Cable audio receivers • CD players
Setup
When you first receive your AllTouch Remote Control, you will have to
tell it each brand of equipment you want it to control. We call this setup. The
cable mode is already set up for home terminals/HCTs.
In the back of this guide, is a list of numbers starting on page 19.
These are setup codes you must use to set up your remote control.
Remember–you must set up the AllTouch Remote Control for each
device you would like it to control.
Batteries are required
Your AllTouch Remote Control has a red light that comes on with each
button press when the batteries are good. The light blinks twice when
the batteries are installed for the first time. If the batteries are low, the
red light blinks twice each time you press a button.
Follow these steps to check the batteries and install new ones if
necessary.
1. Press
POWER
.
Note: If you have not used your remote control
in a while, you may have to press
POWER
several
times to make the red light stay on.
2. Did the red light stay on?
• If yes, the AllTouch Remote Control
batteries are good.
• If no, the batteries are inserted
improperly or the voltage is low. If
you replace the batteries, use two
alkaline AAs.
T6051
VCR
AUX
MENU INFO
POWER
TV
CBL
A
l
l
T
o
u
c
h
®
A
B
C
T6052
+-+-

573497 Rev B
4
What the buttons do
When you know what the buttons do, your AllTouch Remote Control is
easy to use. See the drawing below.
All the button functions listed below represent factory setups. Buttons
that work only with an 8600xHCT are specified.
1 VCR Control VCR.
2 AUX Control CD player or
cable digital audio
receiver.
3 TV Control your TV.
4 CBL Control your home
terminal/HCT.
5 POWER Turn on and off your TV,
VCR, AUX, or home
terminal/HCT.
6 INFO While in all modes and
for home terminal or
HCT, display
information about
selected device (for
example, channel
name, number). For
HCT only while in cable
mode, also display the
title and description of
program you are
watching or of program
you have highlighted in
the viewing guide.
7 SELECT While in CBL mode,
choose items from the
on-screen menus. In
other modes, use to
enter channel number.
8 FAV While in CBL or TV
modes, surf from one
favorite channel to the
next.
MENU INFO
PPV
PREV. DAY NEXT DAY
MUTE
LAST
FAV
POWER
BAC
VCR
1
4
7
2
5
8
0
3
6
9
AUX
V
O
L
SELECT
REW
PAUSE RECSTOP
PLAY FF
SET-UP BYPASS
TV
CBL
C
H
T6053
15 14
23
5
6
7
8
9
1
0
11
1
2
1
3
22
21
20
19
18
17
16
GUIDE
A
l
l
T
o
u
c
h
®
1234

573497 Rev B 5
What the buttons do, Continued
9 LAST While in any mode, return to last channel viewed or to the
previous menu.
10 CH ▲▼ While in any mode, surf through channels.Tune to the
next higher or lower channel.
11 A B C These macro buttons can be programmed by your cable
operator or subscriber to perform multiple key functions in
any mode.
12 NUMBERS While in any mode, change channels by pressing the
number buttons or enter parental control number and
pay-per-view access number.
13 NEXT DAY (8600xHCT only) While in the viewing guides, go to the
next day’s schedule or move forward one page.
14 BYPASS While in CBL mode, use RF bypass to switch cable
programming between your home terminal/HCT and TV.
Requires optional RF accessories.Your cable company
activates this function. While in TV or VCR modes, select
an alternate video input source for the device (for
example,TV/VCR in VCR mode, TV/Video in TV mode).
15 SET-UP Set up this remote to control the TV, AUX, VCR, and other
devices.
16 VCR Control VCR and AUX device functions.
FUNCTIONS
17 PREV. DAY (8600xHCT only) While in the viewing guides, go to the
previous day’s schedule or move back one page.
18 VOL ▲▼ Adjust volume.
19 MUTE Turn off sound.
20 PPV While in CBL mode, display the list of upcoming pay-per-
view (PPV) programs. For 8600x HCTs:You may purchase
PPV programs automatically.
21 ARROWS For 8600x HCTs:While in CBL mode, highlight items on
menus, viewing guides, and screens. For otherhome
terminals: While in CBL mode, use the down arrow button
to highlight menu items.
22 GUIDE (8600xHCT only) While in CBL mode, display the
Interactive Viewing Guide to see what’s on cable.
23 MENU While in CBL mode, go to or leave menus.

573497 Rev B
6
Setting up the remote control to operate your TV
To make the remote control work with your TV, follow this procedure.
Important! If you are using a TV/VCR combination, you should use the
VCR or TV/VCR combination codes. Go to Setting up the remote
control to operate your VCR on the next page.
1. Find the code for your brand of TV in the back of this guide. You
may find more than one code for your particular brand. Start
with the first choice. Remember: If you are using a TV/VCR
combination, use a VCR or TV/VCR combination code.
2. Press and release
TV
, then hold down
SET-UP
until
the red light blinks twice.
Note: You may need to wait a few seconds for the
red light to blink twice.
3. Enter your 3-digit TV code–the red light should
blink twice again. (If the red light does not blink
twice, return to step 1 and try again.)
4. Point your AllTouch Remote Control at your TV
and press
POWER
.
5. Did your TV turn off (or on)?
• If yes, you are finished setting up the remote
control for your TV. Write your TV code on
page 31.
• If no, go to step 6.
Notes:
• You may want to press VOL ▲▼, MUTE, and CH ▲▼ to
verify that all functions work.
• To disable channel control in TV mode, turn to Disabling/
enabling channel control on page 16 and follow the steps.
6. If your TV did not respond, repeat steps 2 through 5 trying all of
the codes (one at a time) under your brand.
7. If your TV still did not respond, turn to All Search on page 10
and follow the steps.
VCR
1
4
7
2
5
8
0
3
6
9
AUX
V
O
L
SELECT
REW
PAUSE RECSTOP
PLAY FF
SET-UP BYPASS
MENU INFO
PPV
PREV. DAY NEXT DAY
MUTE
LAST
FAV
POWER
BAC
TV
CBL
C
H
T6054
SET-UP
TV
GUIDE

573497 Rev B 7
Setting up the remote control to operate your VCR
To make the remote control work with your VCR, follow this procedure.
Important! If you are using a TV/VCR combination, you should set up
your VCR or TV/VCR combination code first, then go back to Setting
up the remote control to operate your TV. Use the same VCR code to
set up your TV, unless noted in code table on page 15.
1. Find the code for your brand of VCR in the back of this guide.
You may find more than one code for your particular brand. Start
with the first choice. Remember: If you are using a TV/VCR
combination, use a VCR code.
2. Press and release
VCR
, then hold down
SET-UP
until
the red light blinks twice.
Note: You may need to wait a few seconds for the
red light to blink twice.
3. Enter your 3-digit VCR code–the red light should
blink twice again. (If the red light does not blink
twice, return to step 1 and try again.)
4. Point your AllTouch Remote Control at your VCR
and press
POWER
.
5. Did your VCR turn off (or on)?
• If yes, you are finished setting up the remote
control for your VCR. Write your VCR code on
page 31.
• If no, go to step 6.
Notes:
• You may want to insert a tape and try
PLAY
,
FF
,
and
REW
to verify that all functions work. To record a
program, press
REC
twice.
• All VCR functions also work in TV and CBL modes.
6. If your VCR did not respond, repeat steps 2 through 5 trying all
of the codes (one at a time) under your brand.
7. If your VCR still did not respond, turn to All Search on page 10
and follow the steps.
VCR
1
4
7
2
5
8
0
3
6
9
AUX
V
O
L
SELECT
REW
PAUSE RECSTOP
PLAY FF
SET-UP BYPASS
MENU INFO
PPV
PREV. DAY NEXT DAY
MUTE
LAST
FAV
POWER
TV
CBL
C
H
T6055
SET-UP
VCR
GUIDE
BAC

573497 Rev B
8
Setting up the remote control to operate other devices
You can use the
AUX
button on your AllTouch Remote Control to set up
your:
• Cable digital audio receiver
• CD player
• Home automation device
To make the remote control work with other devices, follow this
procedure.
1. Find the code for your brand of device in the back of this guide.
You may find more than one code for your particular brand. Start
with the first choice.
2. Press and release
AUX
, then hold down
SET-UP
until
the red light blinks twice.
Note: You may need to wait a few seconds for the
red light to blink twice.
3. Enter your 3-digit device code–the red light should
blink twice again. (If the red light does not blink
twice, return to step 1 and try again.)
4. Point your AllTouch Remote Control at your device
and press
POWER
.
5. Did your device turn off (or on)?
• If yes, you are finished setting up your device.
Write your code on page 31.
• If no, go to step 6.
Note: You may want to try several functions of your device to
verify operation. Button operation (for example, CH ▲▼, LAST,
INFO, etc.) will depend on the AUX device programmed.
6. If your device did not respond, repeat steps 2 through 5 trying all
of the codes (one at a time) under your brand.
7. If your device still did not respond, turn to All Search on page 10
and follow the steps.
VCR
1
4
7
2
5
8
0
3
6
9
AUX
V
O
L
SELECT
REW
PAUSE RECSTOP
PLAY FF
SET-UP BYPASS
MENU INFO
PPV
PREV. DAY NEXT DAY
MUTE
LAST
FAV
POWER
TV
CBL
C
H
T6056
SET-UP
AUX
GUIDE
BAC

573497 Rev B 9
Reprogramming your cable device button
Your AllTouch Remote Control is already set up to operate a Scientific-
Atlanta home terminal/HCT. If your remote control loses its code for
the home terminal/HCT, you need to reprogram your cable device
button. Follow the instructions below.
Notes:
• Not all cable functions work with older Scientific-Atlanta home
terminals.
• In the cable mode, the VOL button will not control the volume
through the home terminal/HCT unless you program it to do so.
See Volume Lock on page 14. The Volume Lock defaults to
TV mode.
The code for your brand of home terminal/HCT is 491.
1. Press and release CBL , then hold down
SET-UP
until
the red light blinks twice.
Note: You may need to wait a few seconds for the
red light to blink twice.
2. Enter 491– the red light should blink twice
again. (If the red light does not blink twice, return
to step 1 and try again.)
3. Point your AllTouch Remote Control at your home
terminal/HCT and press
POWER
.
4. Did your home terminal/HCT turn off (or on)?
• If yes, you are finished setting up your home
terminal/HCT.
• If no, go to step 5.
Note: All VCR functions (
PLAY
,
FF
, etc.) also work in CBL
mode. To record a program, press
REC
twice.
5. If your home terminal/HCT did not respond, repeat steps 1
through 4.
6. If your home terminal/HCT still did not respond, contact your
service provider.
VCR
1
4
7
2
5
8
0
3
6
9
AUX
V
O
L
SELECT
REW
PAUSE RECSTOP
PLAY FF
SET-UP BYPASS
MENU INFO
PPV
PREV. DAY NEXT DAY
MUTE
LAST
FAV
POWER
BAC
TV
CBL
C
H
T6057
SET-UP
CBL
GUIDE

573497 Rev B
10
All Search
If your device does not respond after trying all of the codes for your
brand, try the All Search procedure.
During All Search, the AllTouch Remote Control searches through a
library of codes until it finds the right one for your device. The
AllTouch Remote Control then completes the setup automatically.
Follow the steps below to do an All Search.
1. Turn on the device that you could not set up using the codes.
For example, if all the codes for your brand of VCR did not
respond, turn off your VCR. If the device is a CD Player, turn it
on and insert a disc.
2. Press and release the appropriate button on the remote control.
Device Button
VCR
VCR
Auxiliary (such as a CD player)
AUX
TV TV
HCT/Home Terminal CBL
3. Press and hold
SET-UP
until the red light blinks twice.
4. Press 991. The red light blinks twice.
5. Point your AllTouch Remote Control directly at the device.
6. Press
POWER
(or
PLAY
for CD player) then the appropriate button
(
VCR
,
AUX
,
TV
, or CBL ). Repeat this step until your device turns on
or starts to play. You may have to repeat this 50 or 60 times.
Important! Be patient and go slowly. Allow enough time for the
device to turn on or for the CD player to start.
T6058

573497 Rev B 11
All Search, Continued
7. When your device turns on or starts to play, press and hold
SET-UP
until the red light blinks twice. This step programs the code into
the AllTouch Remote Control.
Your remote control now has the correct code for your device.
Note: Press several keys on the remote control for the device
(VOL ▲, CH ▲,
PLAY
, etc.) to verify that all functions work
correctly.
8. Next, you need to find your device codes. See Getting your codes
on the next page to find the code(s) for your device(s). Write the
codes on page 31.
Notes:
• You may want to inset a disc into your CD player and use
the
PLAY
button on the remote instead of the
POWER
button to
search. When your CD player starts to play, press
SET-UP
to lock
in your code.
• If a device is not found, please make note of its brand, model
number, description, size, etc., and contact your service
provider.
• When you have searched through the complete device code
library, the red light will blink three times. The search will then
start over again from the beginning of the library.

573497 Rev B
12
Getting your codes
After doing an All Search, find your 3-digit device codes. Follow the
steps below to find your codes.
1. Press and release the appropriate button for the device on the
AllTouch Remote Control. For example, if you are getting the
code for your VCR, press and release
VCR
.
Device Button
VCR
VCR
Auxiliary
AUX
TV TV
HCT/Home Terminal CBL
2. Press and hold
SET-UP
until the red light blinks twice.
3. Press 99
0
. The red light blinks twice.
4. Press and release the 1, 2, or
3
buttons on the remote
control to find each digit of the 3-digit code.
After pressing each button, count the number of times the red
light blinks. This number indicates the digit. There is a delay of a
few seconds before the blinks start. If the red light does not
blink, the digit is zero. Record your findings below.
Press this Record the Number of Blinks
Number Button VCR AUX TV
1
2
3
Enter the number
of blinks here
and on page 31. 123 1 23 1 23
5. Important! Remember to write the codes on page 31.
6. Repeat steps 1 through 5 for each device.

573497 Rev B 13
Reassigning mode buttons
Your mode buttons are
VCR
,
AUX
,
TV
, and CBL . They represent your VCR,
auxiliary device, television, and your home terminal/HCT. You can
reassign these buttons to control other devices if you choose. To reassign a
mode button, you copy the features of one button to another button.
For example, you may want your AllTouch Remote Control to control two
TVs instead of a TV and a VCR. You can turn your VCR button into a
second TV button.
To reassign a mode button, follow the steps below.
1. Press and hold
SET-UP
until the red light blinks twice.
2. Press 992. The red light blinks twice.
3. Press the button you want to copy (source button).
4. Press the button you want to reassign (target button). The red
light blinks twice.
5. Set up the reassigned button with the correct device code to
control your device.
To set up for... Go to page...
TV 6
VCR 7
Other devices (AUX) 8
Cable 9
6. Write your changes and new codes in the following table and on
page 31.
Device VCR Aux TV CBL
Reassigned button
(New device)
Code

573497 Rev B
14
Volume Lock
After you program your TV code into your remote control, it will
automatically control the TV’s volume while operating in the TV, VCR,
or CBL modes. You can also program the remote control so that you
can control the volume through the HCT or TV/VCR combination
while operating in TV, VCR, or CBL modes. We call this Volume Lock.
Note: Volume Lock programming will remain active even if batteries
are removed for an extended period of time.
To switch your volume control to a device other than your TV, follow
the steps below.
1. Hold down
SET-UP
until the red light blinks twice.
2. Press 993.
3. Press the appropriate device mode button ( CBL or
VCR
). The red
light blinks twice. Your volume control is now locked to your
selected device mode.
Device Button Result
Home CBL Your remote control will now control the
Terminal volume through your home terminal.
TV/VCR
VCR
Your remote control will now control the
combination volume through your TV/VCR combination.
Important! If you have a TV/VCR combination
unit, you need to enter a TV code to control
volume. Once you enter the TV code, the
volume control will work in any mode. In
most cases the TV code is the same as the
VCR or TV/VCR combination code already
entered, but for the codes noted in the table
on page 15, a different TV code is required for
volume control.
Note: Your AllTouch Remote Control automatically controls only the
volume of your Aux device (CD Player) while in the AUX mode. You
cannot lock the volume to the AUX mode.

573497 Rev B 15
Volume Lock, Continued
TV/VCR combinations’ volume control codes:
VCR code TV code
049 065
062 107
074 061
095 068
176 264
Note: All other TV/VCR combinations use the same VCR or TV/VCR
code for the Volume Lock sequence to activate volume control.

573497 Rev B
16
Disabling/enabling channel control
This function enables or disables TV and VCR mode controls including
Channel Up/Down, Digits 0-9, Last Channel, and Favorite Channel.
With this programmable feature, the TV and VCR remains on the
correct output channel (either 3 or 4) so that the HCT operates
properly.
The channel control in TV and VCR mode is enabled as the factory
default.
To disable channel control in TV and VCR modes:
1. Press and hold
SET-UP
until the red light blinks twice.
2. Press 996. The red light blinks twice.
3. Press CH ▼. The red light blinks twice.
To enable channel control in TV and VCR modes:
1. Press and hold
SET-UP
until the red light blinks twice.
2. Press 996. The red light blinks twice.
3. Press CH ▲. The red light blinks twice.
Note: When TV and VCR channel control is disabled, the cable mode
channel control will be available in these modes.

573497 Rev B 17
Programming the macro buttons
The AllTouch Remote Control provides users with three definable macro
buttons (A, B, and C), which can be programmed by the cable operator or
subscriber. Programming one of the macro buttons enables you to perform
several functions by pressing that key such as switching to cable, turning
on HCT power, and switching to channel 25.
To program a macro button (A, B, or C):
1. Press and hold
SET-UP
until the red light blinks twice.
2. Press 995. The red light blinks twice.
3. Press macro button (A, B, or C).
4. Press one of the mode buttons (
VCR
,
AUX
, TV , or CBL ).
5. Press the function button desired. You may use up to three
function buttons.
6. Press and hold
SET-UP
until the red light blinks twice.
Each macro button may have up to three functions with each function
having no more than four button presses.
To clear a macro button (A, B, or C):
1. Press and hold
SET-UP
until the red light blinks twice.
2. Press 995. The red light blinks twice.
3. Press macro button (A, B, or C).
4. Press and hold
SET-UP
until the red light blinks twice.
Write the function of each macro button in the following table.
Macro button Function
A
B
C

573497 Rev B
18
Troubleshooting
Refer to the following table for solutions if you have trouble operating
your AllTouch Remote Control.
Problem Possible Cause Check and Correct
The red light •The battery Replace the batteries. Use
does not blink voltage is low. two AA alakaline batteries.
when you press •The batteries are Check that the batteries’
POWER
. inserted incorrectly. plus (+) and minus (–) symbols
match the illustration inside the
battery compartment.
The remote You may have the Press:
control does not remote control in •
VCR
for VCR
work properly or the wrong mode. •
AUX
for auxiliary device
home terminal/ •
TV
for TV
HCT functions • CBL for cable
do not work.
You may have used Follow these steps to program
an incorrect code to your remote control with the
program the remote correct code:
control. 1. Try all the codes listed
under the brand of your
device.
2. Try All Search and be sure
to go slowly. (See page 10.)
Important! Be sure to point
your AllTouch Remote Control
directly at your device when you
press
POWER
or
PLAY
.

573497 Rev B 19
Troubleshooting,Continued
Problem Possible Cause Check and Correct
The remote You may have used Try All Search again (see page
control responds an incorrect code to 10). Keep progressing through
to some of the program the remote the library until you discover
codes but with control. the code that supports all
the wrong result. of your features.
Your device is Your device has not Make a note of the brand,
not found been included in number,description (size, etc.),
during an the All Search and contact your service
All Search.database. provider.
(Unfortunately, many
devices use very
similar remote control
codes. While searching
the library with All
Search, you may
have locked onto a
similar code for which
only some commands
work.)

573497 Rev B
20
A-Mark 017
Abex 046
Admiral 107
Adventura 060
Aiko 106
Akai 044
Alaron 193, 197
Ambassador 191
Anam 082, 194
Anam National 069
A C 017, 033, 044, 066,
151, 199
Archer 017
Astro Text 393
Audiovox 017, 106, 194, 465
Baysonic 194
Belcor 033
Bell & Howell 030, 168
Bradford 194
Brockwood 033
Broksonic 017, 250, 477
Candle 044, 060, 070, 200
Carnivale 044
Carver 068
CCE 231, 343
Celebrity 014
Cineral 106, 465
Citizen 044, 053, 060, 070,
074, 106, 200, 294
Clairtone 199
Concerto 070
Contec 171, 172, 194, 199
Craig 194
Crosley 068
Crown 053, 194
Curtis Mathes 030, 044, 053, 074, 061,
065, 068, 070, 168, 429,
465
CXC 194
Daewoo 465, 033, 053, 105, 106
Daytron 033
Denon 159
Dumont 031, 033
Electroband 014, 199
Electrohome 395, 403, 423
Emerson 250, 477, 033, 052, 053,
168, 172, 191, 192, 193,
194, 196, 197, 199, 250,
294, 296, 477
Envision 044
Fisher 168, 173
Fujitsu 193
Television setup codes (Most popular codes listed first)
Television
brand 3-digit codes Television
brand 3-digit codes