FACTORY DEFAULTS
2WWW44WWWWWWW4W4W444*<
('-WWWWWWWWWWWWWWW4WW44
!!"0WWWWWWWWW4444444442
&1-0W4WWWWWWWWWWWWW444444444
(0WWWWWWWWWWW44WWWW440;<
&:0WWWWWWWWWWWWW44WWW4440;
20%WWWWWWWWWWWW444WW441
&"0%WWWWWWWWWWWW444W1
110;<0%WWWWWWWWW44W41
110;0%WWWWWWWWWW4441
1#/-/WWWWWWWWWW444WW441
'$0WWWWWWWWWWWW44WW4
&0WWWWWWWWWWWW44W44W44
B1D-WWWWWWWW444WWWO
B1;*WWWWWWWWW44W444WW4A
B1;WWWWWWWWWWW444W444A
B10;<WWWWWWWWWWWW44444A
B10;WWWWWWWWWWW44444444A
'$WWW4WWW444444W4<%B)'$
&!$%WWWWWW44WW444WWW4A&!$
&!$WWWWWWWWWWWWW444WWWW4WWWW40
BASIC PROGRAMMING
D--.(-$32,-
))4&)
,-
$4%----.-
4&)-,-
)---4%-
-)-4%-
-),-
-)!4
Enter ng Programm ng Mode
%-!28)X*<9
24
Press: # 9 # Master Code
Master Code = the current 6-digit Master Programming Code
Sett ng Entry Code Length Default: 4 d g ts
Press: 0 3 # Length #
Length = 4-6 for entry code length
Note: If the Entry Code Length is going to be changed from the factory
default of 4 digits, make this change first before programming any entry
codes.
Add ng a New Entry Code
Press: 0 1 # Code # Code # elay #
Code=The new entry code: 1-999999, depending on code length
elay=Relay output entry code will activate:
1=Main Relay 2=Auxiliary Relay 3=Both Relays
10=Relay #1, toggled 20=Relay #2, toggled 30=both Relays toggled
12=Relay #1 toggled; Relay #2 timed open
21=Relay #1 timed open; Relay #2 toggled
%-)- $--.-
)4%-
---4
/)--)-
,--4&
4
Note: Leading zeros (zeros before the code number, i.e.0001 do not need to
be entered when programming a new code. The 920 will internally add any
zeros to fill digits determined by the entry code length setting. Leading zeros
will have to be entered by the user when entering their code to gain access.
Eras ng a S ngle Entry Code
Press: 0 2 # Code # Code #
Code=The entry code to delete
%-)- $--.-
)-4%---
-4
Eras ng All Entry Codes
WA NING: PE FO MING THIS COMMAND WILL EMOVE
ALL ENT Y CODES F OM THE MEMO Y
Press: 9 7 # 0 0 0 0 0 0 # 0 0 0 0 0 0 #
Note: The green indicator will light while the memory is being erased. This
may take up to 15 seconds.
Chang ng the 6-D g t Master Programm ng Code
Press: 9 8 # Master Code # Master Code #
Master Code=The new 6-digit Master Programming Code
A?YYYYYYYYYYYY
PROGRAMMING OPTIONS
%-.(-$34
,-))))4
%-$2$-
-4
Programm ng the 920 To Hold the Output
1M(-$3-6%
27)-!4D-
)%2,-)
00A)0A0-4D-
,-'()-))4
%-)?
If the output is OFF, it will turn ON and stay on until the next
activation.
If the output is ON, it will turn OFF and stay off until the next
activation.
?@/A1%&''&%/0A/A1%@&@/A1%!.@/A1%!.4B<!*
Ex t ng Programm ng Mode
Press: #
%--)"2
Note: The 920 will automatically exit Programming Mode after
two minutes of inactivity
NN
Re-enter ng a Command After a M stake
/)--,,
$,-$
!-?
Press: 9 #
N
