Sealey AP24212 User manual

INSTRUCTIONS FOR
MOBILE WORKSTATION 12/16 DRAWER WITH
BALL BEARING RUNNERS
MODEL NO’S: AP24212 & AP24216
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this product.
8DO NOT open more than one drawer at a time.
8DO NOT step on the drawers.
8DO NOT let children near the tool chest.
8DO NOT use in damp areas.
9Ensure drawers are fully closed and the self locking catch is activated before moving the tool chest.
9Keep the work area clean and ensure there is adequate lighting.
WARNING! The warnings, cautions and referred to in this instruction manual cannot cover all possible conditions and situations that may
occur. It must be understood that common sense and caution are factors that can not be built into this product, but must be applied by the
operator.
2. INTRODUCTION
Heavy gauge steel with double wall construction for extra strength and durability. Ball bearing drawer runners provide superior performance and
carry heavier loads. Each drawer tted with catch to prevent unexpected opening, when being transported around the workshop. Added security
provided by side mounted cylinder locks, supplied with two keys. Recessed handles permit units to be slotted in work environments where space
is tight. Rust and solvent resistant powder coat paint nish. Fitted with anti-shock protection on all four corners to prevent accidental damage.
Tough composite top allows these units to be used as a workstation.
3. SPECIFICATION
AP24212, AP24216| Issue:3 (L) 15/06/17
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Model No. AP24212 AP24216
Dimensions (W x D x H) (W x D x H)
Overall Size 1130 x 565 x 1000 1130 x 565 x 1000
Drawers Qty Qty
Medium Drawer 3 533 x 391 x 58 6 533 x 391 x 58
Large Drawer 2 533 x 391 x 128 2533 x 391 x 128
X-Large Drawer 1533 x 391 x 195
Medium 1/2 Drawer 3 268 x 391 x 58 6 268 x 391 x 58
Large 1/2 Drawer 2268 x 391 x 128 2268 x 391 x 128
X-Large 1/2 Drawer 1533 x 391 x 195
Optional Accessories
Model No. Description
AP24ACC2 Side Shelf with Paper Roll Holder
AP24ACC3 Document Holder
AP24ACC4 Waste Bin
AP24ACC5 Can and Bottle Holder
AP24ACC6 Drawer Divider 3 x 395 x 58mm
AP24ACC7 Drawer Divider 3 x 395 x 120mm
AP24ACC9 Short Hook Set x 10pcs
AP24ACC10 Medium Hook Set x 10pcs
AP24212 AP24216

4. OPERATION
4.1. Each drawer is fitted with a catch mechanism on the right hand side of the drawer underneath the handle, to open drawer push the catch
to the left to release the catch and pull the drawer open (Fig.1).
WARNING! Only open one drawer at a time and DO NOT overload the drawers (Fig.2).
4.2. When moving the workstation, ensure that the drawers are closed and locked (Fig.3) to prevent accidental opening, release the brakes
as shown in Fig.4 and move the workstation using the handles and maintain full control. When the workstation has been moved to the
required location, lock the brakes.
WARNING! DO NOT move across slopes of more than 5 degrees as the workstation may tilt.
Original Language Version
© Jack Sealey Limited
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Fig.1
Fig.2
Fig.3 Fig.4
AP24212, AP24216| Issue:3 (L) 15/06/17