Sealey HT106LED.V2 User manual

INSTRUCTIONS FOR
HEAD TORCH 3W CREE LED AUTO
SENSOR RECHARGEABLE
MODEL NO: HT106.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL
9Ensure the lamp is fully charged before initial use.
8DO NOT turn the lamp on when it is being charged.
8DO NOT shine directly into your, another person’s or an animal’s eyes.
8DO NOT allow children to use the lamp.
8DO NOT handle or move the lamp whilst it is being charged.
8DO NOT use the lamp if you suspect that the battery or the lamp casing is damaged.
8DO NOT leave battery in a discharged state, recharge battery immediately. Before storage, fully recharge the battery, subsequently
recharge the battery at least once every six months of non-use.
WARNING! To reduce the risk of burns or re:
8DO NOT attempt to open, disassemble, modify or service the battery pack.
8DO NOT crush, puncture, short external contacts or dispose of in re or water.
8DO NOT expose to temperatures above 60°C (140°).
9Replace only with the battery pack designated for this product.
9Recycle or dispose of used battery as stipulated by local regulation.
9If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool
water and seek immediate medical attention.
2. INTRODUCTION
Hands free 3W CREE XPE LED spotlight with adjustable inclination to direct light as required. Features auto sensor switch on/off just by waving
hand in front. Alternatively can be over ridden to stay on/off by push button. Adjustable headband and foam brow for added comfort. Powered by
rechargeable 3.7V 1.5Ah Li-ion battery. Supplied with micro USB charging lead.
Refer to
instruction
manual
Fig.1
HT106LED.V2 Issue: 2(SP) - 11/04/17
Original Language Version
© Jack Sealey Limited

3. SPECIFICATION
Model no: ....................................................... HT106LED.V2
Lumen output: .............................................................. 180lm
Battery: .......................................................3.7V 1.5Ah Li-ion
LED:.......................................................................3W CREE
Operating time: ...............................3hr@100%, 10hr @ 30%
Charging time:...................................................................4hr
4. OPERATION
4.1. Chargingrefertog.2
4.1.1. Connect the USB lead to the socket on the bottom of the battery, see g.2 and a USB power socket. Turn on the power supply. The
LED charging light on the bottom of the battery will light RED to show that charging has commenced.
4.1.2. When the battery is fully charged the LED will light GREEN.
4.2. Operation refertog.1
4.2.1. Press the on/off switch once for full light, twice for 30% light and three times for ashing light.
4.3. Auto-sensorrefertog.1
4.3.1. Press the auto-sensor button once to turn it on, the button will glow red.
4.3.2. Move a hand past the sensor to turn the light on and past it again to turn it off.
4.4. Rear light
4.4.1. Pressing the auto button sensor for 2 seconds will switch on the rear red ashing light. This can be switched off by switching off the
front light, which will reset the lights without the rear red light.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Sole UK Distributor, Sealey Group.
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk.
IP32 7AR
www.sealey.co.uk
[e-mail]
01284 757500
01284 703534
Web
Fig.2
HT106LED.V2 Issue: 2(SP) - 11/04/17
Original Language Version
© Jack Sealey Limited
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
Battery Removal
The battery can be removed by prising the battery pack apart. Use great care so as to not damage the battery. Cut wires
one at a time and remove battery. Dispose of in an environmentally protective way.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential
 purchasersofproductscontainingbatteries(asdenedwithintheseregulations),thattheyareregisteredwithValpak’s
 registeredcompliancescheme.JackSealeyLtd’sBatteriesProducerRegistrationNumber(BPRN)isBPRN00705.