Sealey IRC153110V User manual

INSTRUCTIONS FOR
INFRARED CABINET HEATER 1.5/3KW 110V
MODEL NO: IRC153110V
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. Electrical Safety
WARNING! It is the user’s responsibility to check the following:
9Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey dealer. If the heater is used in the course of business duties, it
must be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
9Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9Ensure that the voltage rating on the appliance suits the power supply to be used.
8DO NOT pull or carry the appliance by the power cable.
8DO NOT pull the plug from the socket by the cable.
8DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
replaced immediately by a qualied electrician.
9 This product is tted with a EN 60309 (110volt 32amp) plug.
9If the cable or plug is damaged during use, switch the electricity supply and remove from use.
9Replace a damaged plug with a EN 60309 (110volt 32amp) plug If in doubt contact a qualied
electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
9Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualied electrician.
1.2. General Safety
WARNING! Disconnect the heater from the mains power supply before carrying out any servicing or maintenance.
9Maintain the heater in good order and clean condition for best and safest performance. Replace or repair damaged parts.
9Locate heater in a suitable work area and keep area clean, tidy and free from unrelated materials. Ensure there is adequate
lighting and keep the immediate area in front of the outlet grille clear.
9Allow the unit to cool before storage. When not in use, disconnect from the mains power supply and store in a safe, cool, dry,
childproof area.
9Only use the heater standing in the upright position on a level surface.
8DO NOT use the heater where there are flammable liquids, solids or gases such as petrol, solvents, aerosols etc, or where heat sensitive materials
may be stored.
8DO NOT place the heater near items that may be damaged by heat, allow at least 2mtr clearance in front of the heater.
8DO NOT allow the heater to get wet as this may cause an electric shock, causing damage to the heater and possible personal
injury.
8DO NOT let power lead hang over an edge (i.e. table), or touch a hot surface, lie in the beam of heat, or run under a carpet.
8DO NOT use in bathroom, shower room, or in any wet or damp environments or where there is high condensation.
8DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8DO NOT insert or allow objects to enter any openings of heater as this may cause an electric shock, fire or damage to heater.
8DO NOT use heater if the power cord, plug or the heater is damaged, or if the heater has become wet.
8DO NOT use the heater for any purpose other than for which it is designed.
8DO NOT use a timer or other remote device to operate the heater.
8DO NOT touch the quartz lamps, even when cold.
8DO NOT use the heater without the wheels fitted and locked.
8DO NOT allow children to touch or to operate the heater.
8DO NOT site the heater below an electrical socket outlet.
8DO NOT use the heater without the grille fitted.
IRC153110V | Issue1 20/04/16
Original Language Version
© Jack Sealey Limited
Refer to
Instruction
Manual
Hot Surfaces Warning
Electricity
Brown
(L)
Yellow/
Green
(E)
Cable
restraint
Blue(N)

8DO NOT use the heater out of doors. These heaters are designed for indoor use only
8DO NOT cover heater when in use, and do not obstruct the air inlet and outlet grilles.
8DO NOT place heater too close to yourself or any object, allow the air to circulate freely.
8DO NOT touch the outlet grille of the heater during and immediately after use as it will be hot.
2. INTRODUCTION & SPECIFICATIONSP
Powder coated metal cabinet with two quartz infrared elements and chemically polished reflectors for maximum heat emission. Controllable power
output by rocker switches on the side of the cabinet. Features easy-rolling swivel castors with 2 locking castors. Suitable for wide range of heating
including restorative applications. Supplied with power cable.
Model No............................................................ IRC153110V
Power output (2 heat settings) ...................... 1500/3000 Watt
Size WxDxH................................................575x490x870mm
Supply.....................................................................110V-32A
3. ASSEMBLY
3.1. Attach the wheel sub-assemblies to the base of the heater using the bolts provided. Ensure the lockable
wheels are to the rear of the heater.
3.2. Attach the handle to the top of the heater using the bolts provided, ensuring the shaped spacers
are fitted between the heater and the handle as shown.
3.3. Remove the front grille by unscrewing the retaining screws.
3.4. Extract the lamps from the shipping carton.
Warning! Never touch lamp glass directly with fingers, only touch the ceramic ends or use a soft
cloth, otherwise elements could be damaged.
3.5. Carefully insert each lamp into the two push-in side fittings with a gentle pressure.
3.6. Check the lamps are properly located.
3.7. Reassemble front grille.
4. HEATER OPERATION
4.1. Place the heater on a level floor in the area you require to heat. Allow a minimum of 2mtr between
the heater and adjacent objects.
4.2. Plug the heater into the mains supply and select the required output by using the two rocker switches on the side which switch the
elements on and off. Each lamp has an output of 1500W.
4.3. To switch the unit off, select “0” on both the rocker switches and unplug from the mains. Allow the unit to cool before handling or storage.
WARNING! DO NOT touch the top of the heater when in use as it becomes hot.
WARNING! Always allow elements to cool before moving the units. Use only on a smooth even surface. Failure to do so will cause premature
wear to the lamps and reduce their working life.
4.4. The heater has a built in tilt switch safety mechanism that switches off the unit if it is tilted beyond 35° either forwards or backwards.
This prevents fire in the event of the unit being knocked over. If the unit does not turn on again when returned to the vertical, tip it
approximately 35° in the opposite direction until you hear the internal switch operate. As the heater switches on return it to the vertical
position.
5. MAINTAINANCE
Warning! Before attempting any maintenance ensure the unit is unpluged from the mains power supply, it is cool and on level ground.
8DO NOT touch the element glass, even when cold.
8DO NOT use the heater with out the grills tted.
5.1. To clean the reector, remove the front grill by unscrewing the retaining screws and wipe the reector with a clean dry cloth. DO NOT
use abrasives or solvents. The surface of the reector is very soft and scratches may cause it to overheat. Replace the grille.
5.2. To change the element remove the front grille by unscrewing the retaining screws.
5.2.1. Ease the sprung sockets on the ends of the element back and pull the element forward so that it clears the socket, remove element.
Warning! Never touch element glass directly with fingers, only touch the ceramic ends or use a soft cloth, to prevent damage.
5.2.2. Carefully insert the replacement lamp into the two push in side fittings with gentle pressure.
5.2.3. Check the element is properly locate, then replace front grill.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Sole UK Distributor, Sealey Group.
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk.
IP32 7AR
www.sealey.co.uk
[e-mail]
01284 757500
01284 703534
Web
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic
Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way.
Contact your local solid waste authority for recycling information.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [e-mail] or telephone [phone].
IRC153110V | Issue1 20/04/16
Original Language Version
© Jack Sealey Limited