Sealey GSS1515G User manual

 WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when building this shed.
 Keep the work area clean, uncluttered and ensure there is adequate lighting.
 Keep children and unauthorised persons away from the working area.
DO NOT use the shed for any purpose other than that for which it is designed.
 Use appropriate safety clothing including eye protection.
The assembly of this product will require assistance.
 DO NOT attempt assembly in windy conditions.
INSTRUCTIONS FOR:
GALVANIZED STEEL SHED GREEN
1.5 X 1.5 X 1.9M
MODEL NO: GSS1515G
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAFETY
2. INTRODUCTION
3. SPECIFICATION
Galvanized, steel panels easily assembled to form a rigid and secure shed, has skillion (sloping) roof and single door. Door is secured by cross
bolt and eyelet which will accept a padlock (not supplied) for additional security. Supplied with bolt-down xing kit.
Model No: .................. GSS1515G
Overall Size: ........1500 x 1500 x 1900mm
Roof Type: ......................Skillion
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

Concrete slab: It is recommended that the shed is secured to a concrete slab as shown below.
Please ensure that the site is level. It is recommended that the slab is 100mm thick and you use builders
plastic and F52 reinforcing mesh. We recommend that you make the slab 100mm bigger than the base
dimensions of the shed. This will allow for a 50mm edge around the shed. We recommend that you
slope the 50mm edges downward by 10 mm so that rain water can be drained away from the shed.
4. CONCRETE SLAB
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

Check all parts against the parts list.
Picture Description Component Location Part
No. QTY Check
Sheet Sheet 2057x770 zinc-
left rear wall 6L 1
Sheet Sheet 2057x770 zinc-
right
rear wall 6R 1
Sheet Sheet 1977-2057x770
zinc-left side wall 7L 1
Sheet Sheet 1977-2057x770
zinc-right side wall 7R 1
5. TOOLS REQUIRED
6. CONTENTS
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

Sheet Sheet 1900-1980x770
zinc-left side wall 2L' 1
Sheet Sheet 1900-1980x770
zinc-right side wall 2R' 1
Sheet Sheet1600x770 zinc roof 8 2
Sheet Sheet 1900x708 zinc front 4 1
Door Sheet 1845x770 zinc door 5R 1
Channel channel 1508 zinc roof 20A 4
Channel channel 1508 zinc rear wall 20B 1
Channel channel 1508 zinc rear wall 20C 1
Channel channel 1508 zinc front 20D 1
Channel channel 1508 zinc front 20E 1
Channel channel 1515 zinc side wall 25 2
Channel channel 1898 zinc front 22 1
Channel channel 775 zinc front 23 1
Channel channel 1458 zinc rear wall
side wall 31 3
Channel channel 674 zinc front 33R 1
Jamb jamb 1898 white front 41A 1
Jamb jamb 1898 white front 41B 1
Jamb jamb 775 white front 42 1
Lip lip 1601 zinc roof 51 2
FITTINGS PACK
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

Picture Component QTY Picture Component QTY
Self tapping
screws(10mm) 140
Self tapping
screws(16mm)
10
4*10mm Rivet 12 3*10mm Rivet 6
Pad bolt 1 Keeper 1
Bracket 8 M8*18m/m Hexagonal bolt 8
M8 Hexagonal Nut 8 Mid wall brace bracket 3
Self tapper safety cover 25 Channel safety cover
(L type) 1
Channel safety cover
(R type) 1Rawl bolt 8
In the unlikely event that you nd you are missing a part, please contact your Sealey dealer.
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

7. PARTS DIAGRAM
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

8.1. Assemble rear wall panels.
You will nd it easier to assemble the shed using sawhorses with timber studs attached
(timber needs to be the same length as the shed (1.5m) or alternatively, a trestle table.
8.1.1. Place 6R and 6L sheeting on the work table and join together with the self tapping screws as per
the diagram.
8.1.2. Now t 20B top channel and 20C bottom channel to the sheeting by tapping it in (diagram A) or
sliding it in. (diagram B) Note that the small lip of the channel is always facing out. This is to ensure
that rain water cannot build up inside the shed.
8. ASSEMBLY
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

8.1.3. Now t 31 mid wall channel to the sheeting and position it using the self tapping screws. Please
note that the groove should face downwards. Position the top and bottom channels using the self
tapping screws as well.
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

8.2. Assemble the side wall panels.
8.2.1. Place 2R and 7R the sheeting on the work table and tap or slide in 25 top channel and 20A bottom
channel. Fix and position the 31 mid wall channel using the self tapping screws. Fix 20A the bottom
channel with the self tapping screws but not 25 the top channel in this stage. Note that the small lip
of the channel is always facing out. This is to ensure that rain water can not build up inside the
shed. Repeat the same steps for 2L and 7L the other side wall.
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

8.3. Assemble the roof panel.
8.3.1. Place two 8 sheetings on the work table and join together with the self tapping screws as per the
diagram.
8.3.2. Now tap or slide in 20A and 20A channels to the sheeting and x them using the self tapping
screws.
8.3.3. Now t two 51 side lips to the sheeting and x them using the self tapping screws.
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

8.4. Assemble the front wall panel and front door.
8.4.1. Place 4 sheeting on the work table. Fit 20D the top channel, 20E the bottom channel
41B the jamb (there are pre-drilled holes for the next step on both 4 and 41B and these
must be aligned) and 33R the mid wall channel to the sheeting and x them using the
self tapping screws (not those with cross mark at this stage).
8.4.2. Fit the 41A jamb, 42 jamb and 23 bottom channel in and x them using the self tapping
screws (not those with cross mark at this stage). Be aware of the joint details as per the
diagrams). Diagram B is the same as diagram A.
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

8.5. Assemble the front wall panel and front door.
8.5.1. Fit 5R pre-assembled door to the front wall panel as per the diagram. Use riveter to x the door
into the pre-drilled holes. Fix 70 pad bolt (but NOT its keeper in this stage) to the pre-drilled
holes and rivet or use self tapping screws as required.
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

8.6. Fit the panels together.
8.6.1. Attach the side walls to the back wall, then the front wall, then the roof. Fix all the components using
the self tapping screws. Fix 71 pad bolt keeper with rivets or screws as required.
For greater security t rivets as below.
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

RAWL BOLT
8.6.2. Now t the bolt down kit as per the diagram. Strengthen the mid wall brace by applying 72
the mid wall brace bracket on each corner.
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

8.6.3. Apply channel safety cover Ltype on channel 32 and Rtype on channel 33R.
Apply the self-tapper covers on the screws xed on the wall to prevent accidental injuries.
Original Language Version GSS1515G Issue: 1 - 26/09/14
© Jack Sealey Limited

8.6.4. If required, the door can be assembled on the opposite side. Align the door with the edge and drill
new holes. Remove the pin from the hinge and reverse it before assembling the door. Fill the old
pre-drilled holes with rivets if required. Perform the same procedure for the pad lock.