Sealey VS2074 User manual

INSTRUCTIONS FOR
AIR HAMMER ADAPTOR FOR INJECTOR PULLER
MODEL NO: VS2074
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.
WARNING! Always use caution when working around fuel systems. The fuel in the fuel rail may be pressurised even if the
engine is not running.
IMPORTANT: These instructions are provided as a guide only. Always refer to the vehicle manufacturer’s service instructions, or a
proprietary manual, to establish the current procedure and data, also any warnings or cautions particular to the vehicle.
8DO NOT use the puller if any parts are missing or damaged.
8DO NOT use this puller for any purpose other than that for which it is designed.
8Switch off vehicle’s ignition and disconnect the battery before commencing work under the bonnet.
8Never lay tools on the vehicle’s battery. This may short the terminals together, causing harm to yourself, the tools, or the battery.
8Operate in a well ventilated area. Do not inhale fuel vapours.
8Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer.
8Wear suitable clothing to avoid snagging. Do not wear jewellery and tie back long hair.
8Keep children and other unauthorised persons away from the working area.
8Keep yourself, tools, and test equipment away from hot engine parts.
8Always keep a fire extinguisher close by, that is suitable for fuel/electrical/chemical fires.
8NEVER smoke or have open flames near vehicle.
9Always relieve fuel pressure before disconnecting fuel lines from injectors.
9Use a rag to cover fuel line fittings, when connecting or disconnecting fuel lines. Avoid contact with fuel.
9Clean up all fuel spills immediately and dispose of all rags properly.
9Maintain the tool components in good and clean condition for best and safest performance.
9When work on the vehicle is finished, ensure all connections on vehicle are restored, and that there are no tools left in the engine bay.
9Store in a safe, dry, childproof location.
2. INTRODUCTION
For use with Sealey injector puller slide hammer sets Model no’s VS2059, VS2064 or similar tool that has a minimum 350mm shaft length and
suitable air hammer. Adaptor allows the air hammer to be used, to vibrate the injector loose instead of using a slide hammer. Ideal for stubborn
injectors when an alternative method of removal is required. Supplied in storage case.
3. SPECIFICATION
Model no: ................................................................. VS2074
Adaptor shank size:....................................401” Parker Taper
VS2074 | Issue 1 18/11/15
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear eye
protection
Wear ear
protection
Wear
protective
gloves

4. OPERATION
4.1. Follow the instuctions of the injector puller kit to remove the
 particularinjector/componentttedtothevehicle.
4.2.  Insteadofttingtheslidehammertotheshaft,ttheclamp
and tighten the two hex headed screws to retain it in place
against the handle.
4.3. Insert the adaptor into the air hammer.
4.4. Connect the shaft assembly onto the injector/compnent to
be removed.
4.5. Insert the adaptor/air hammer into the clamp and hold the
hammer with one hand and the handle with the other.
Note: DO NOT point the tool at the face.
4.6. Use the air hammer for short bursts on a low setting
increasing the vibration level as required.
Note: DO NOT use the trigger lock setting.
4.7. As the injector begins to move reduce the upward pressure
 sothethetooldoesnotyout.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Sole UK Distributor, Sealey Group.
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk.
IP32 7AR
www.sealey.co.uk
[e-mail]
01284 757500
01284 703534
Web
VS2074 | Issue 1 18/11/15
Original Language Version
© Jack Sealey Limited
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.