Sealey VS820UA.V3 User manual

BRAKE AND CLUTCH BLEEDING SYSTEM
UNIVERSAL ADAPTOR
MODEL NO: VS820UA.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL SAFETY
WARNING! Ensure that Health and Safety, local authority and general workshop practice regulations are adhered to when using
tools.
8DO NOT use adaptor if damaged.
8DO NOT use the adaptor to perform a task for which it is not designed.
8DO NOT allow untrained persons to use the adaptor.
8DO NOT use when tired or under the inuence of drugs, alcohol or intoxicating medication.
9Maintain adaptor in a good and clean condition for the best and safest performance.
9Ensure that the ignition key is removed, to prevent inadvertent engine cranking.
9 If the vehicle to be worked on is raised, ensure that it is adequately supported with axle stands or ramps and wheel chocks.
9Wear approved eye protection. A full range of personal safety equipment is available from your Sealey stockist.
9Wear suitable clothing to avoid snagging. DO NOT wear jewellery and tie back long hair.
9Keep children and unauthorised persons away from the work area.
9Keep work area clean and tidy and free from unrelated materials.
9Ensure the work area has adequate lighting.
9Account for all tools being used and DO NOT leave them on or in the vehicle.
1.2. BRAKE FLUID PRECAUTIONS
9Always read and comply with the warnings on the brake fluid container.
9Wear eye protection and keep skin contact to a minimum. If brake fluid enters eyes
rinse with plenty of water and seek medical advice. If swallowed seek medical advice
immediately.
WARNING! Brake fluid is flammable - keep away from sources of ignition, including hot
surfaces e.g. exhaust manifold.
WARNING! Brake fluid will damage paintwork. Any spillage should be flushed with water
immediately.
9 Always read and comply with the warnings on the brake uid container.
WARNING! DO NOT pollute the environment by allowing uncontrolled discharge of
uids. Dispose of waste liquids in accordance with local authority regulations.
9After use, clean equipment and store in a cool, dry, childproof area.
2. INTRODUCTION
Universal reservoir cap for Model No’s VS820, VS821 & VS0204A Brake & Clutch
Bleeding Systems. Supplied with quick connect.
3. OPERATION
3.1. Refer to fig.1
3.2. Insert the two J-bolts through the holes in the adaptor cap and fit the tightening
knobs provided.
3.3. Remove the brake fluid reservoir cap and fit the adaptor cap centrally over the
reservoir filler neck.
3.4. Attach one end of the chain to the hooked end of one of the J-bolts, run the chain
under the master cylinder and attach to the second J-bolt.
3.5. Tighten the two knobs evenly to clamp the adaptor cap onto the reservoir.
3.6. Disconnect the threaded cap from the end of the outlet tube on VS820 and
connect the adaptor cap tube in its place. Follow the VS820 Bleeding
System operating instructions, as normal.
g.1
VS820UA.V3 Issue 2 (HF) 24/10/18
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear safety
footwear
Wear protective
clothing
Warning
corrosive
substance
Warning

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
VS820UA.V3 Issue 2 (HF) 24/10/18
Original Language Version
© Jack Sealey Limited