Sealey LED315 User manual

15W COB RECHARGEABLE WORK LIGHT
MODEL NO: LED315
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL SAFETY
8DO NOT cover the lens whilst the light is on and allow su󰀩cient time to cool before storing.
9 Ensure the light is fully charged before initial use.
8DO NOT turn the light on when it is being charged.
8DO NOT shine directly into your, other person’s or animal’s eyes.
8DO NOT allow children to use the light.
8DO NOT handle or move the light whilst it is being charged.
8DO NOT use the light if you suspect that the battery or the casing is damaged.
8DO NOT leave battery in a discharged state, recharge battery immediately. Before storage, fully recharge the battery, subsequently
recharge the battery at least once every six months of non-use.
1.2. ELECTRICAL SAFETY
9 Use only the USB charging lead supplied to charge the battery.
WARNING! It is the user’s responsibility to read, understand and comply with the following electrical instructions:
9 You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products, particularly portable equipment which is plugged into an electrical
supply not protected by an RCCB. You must also read and understand the following instructions concerning electrical safety.
1.2.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualied
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualied electrician.
1.2.3. You must ensure that you:
9 Inspect the cable and connector for wear and damage to ensure items are safe before connecting to the power supply.
8DO NOT use if worn or damaged.
1.3. BATTERY SAFETY
WARNING! To reduce the risk of burns or re:
8DO NOT Attempt to open, disassemble, modify or service the battery pack.
8DO NOT Crush, puncture, short external contacts or dispose of in re or water.
8DO NOT Expose to temperatures above 60°C (140°F).
9 Recycle or dispose of used battery as stipulated by local regulation.
9 If the electrolyte in the cells gets on your skin, thoroughly wash with water. If it gets in your eyes, rinse thoroughly with cool water and
seek immediate medical attention.
2. INTRODUCTION
15W COB Rechargeable Work Light. 360 Degree rotatable LED light capable of producing up to 1000 Lumens with a built-in rechargeable
lithium-ion 2000mAh battery. Other features include a hanging hook and a strong magnet for multiple applications as well as an emergency
power bank function and power level indicator. Supplied with a USB cable for input/output charging, with a run time of 3hrs and charging time
of 3-4hrs.
3. SPECIFICATION
LED Type: ..................................1 x COB LED
Lens diameter: ...................................... 27mm
Lumen Output: .............. 1000 (high) 500 (low)
Battery: ....................................3.7V 2000mAh
Operating Time: ....................................3-4hrs
Power: ......................................................15W
LED315 Issue 1 09/06/22
Original Language Version
© Jack Sealey Limited
Refer to
instructions

4. OPERATION
4.1. CHARGING
4.1.1. Insert the micro USB plug on the USB cable into the charging port on top of the lamp.
4.1.2. Plug the other end of the USB cable into a 5V USB outlet.
4.1.3. WARNING! DO NOT turn lamp on whilst charging.
4.1.4. The battery indicator will blink during charging.
4.1.5. When the battery has charged fully, the battery indicator will remain lit.
4.2. USE OF LAMP
4.2.1. Direct the lens away from your eyes, other people and animals before switching on.
4.2.2. Press the ON/OFF switch once for high power mode, twice for low power mode, three times for ashing red light mode
4.2.3. The lamp may be held by the handle or attached to any ferrous surface by using the magnet. When the light is attached by the
magnet, it can be rotated through 360° for more precise positioning.
4.2.4. IMPORTANT: Only use the cable supplied with the product.
5. MAINTENANCE
5.1. Keep the light clean by wiping with a damp cloth.
5.2. Store light in a dry childproof area.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Original Language Version
© Jack Sealey Limited LED315 Issue 1 09/06/22
g.1
Charge portOn/O󰀨 Switch
Battery
indicator