Second Wind 1000KCS Manual

1

2
All Second Wind Air Purification portable systems have a (3) year unit and 1 year lamp
warranty. (MODELS:1002kcs, 1000 ka-kcs, 1001 ka-kcs)
ONE (1) YEAR COVERAGE LAMPS
The lamps are warranted by Second Wind for a period of one (1) year from the date of the
original installation, when installed and operated in accordance with Second Wind
recommendations. If during this period a lamp fails, Second Wind will provide a free
replacement. You must pay shipping charges and all other costs of warranty service. Second
Wind will not pay labor involved in diagnostic calls or in removing, servicing, or replacing
parts.
THREE (3) YEAR COVERAGE UNIT
The covered equipment and covered components are warranted by Second Wind for a
period of three (3) years from the date of the original unit installation, when installed and
operated in accordance with Second Wind recommendations. If during this period a covered
component fails, Second Wind will repair or replace the part. You must pay shipping
charges and all other costs of warranty service. Second Wind will not pay labor involved in
diagnostic calls or in removing, servicing, or replacing parts.
REPAIRS
All repairs of covered components must be made with authorized service parts. Labor
charges resulting from diagnostic calls or service are not covered by this warranty.
CARE OF EQUIPMENT
Your new Second Wind Air Purifier must be properly installed, operated and maintained in
accordance with the unit installation, operation, and maintenance instructions provided with
each unit. Failure to provide maintenance per Second Wind instructions will void warranty.
1 Do not look directly at the lamps, without UV protective glasses.
2 Read instruction manual before operating the units.
3 Use recommended accessories (i.e. lamps, ballast)
4 Make sure unit is installed so that the UV light can not be seen directly through any returns or supplies.
5 Check damaged parts: Before further use of the unit, any damaged part should be carefully checked to
ensure that the unit will operate properly. Any part that is damaged should be properly repaired or
replaced.
6 Units should not be installed with in 12-18 inches of any non UV resistant materials. If materials are in
question call manufacturer of said products to see if they are made with UV inhibitors. Prolonged UV
exposure will degrade non UV resistant materials. Non UV resistant materials must be shaded or cov-
ered.

3
All Second Wind Air Purification portable systems have a (3) year unit and 1 year lamp
warranty. (MODELS:1002kcs, 1000 ka-kcs, 1001 ka-kcs)
1 Be prepared to furnish the following information:
a- Complete model number and serial number
b- Proof of installation date if warranty claim is made by other than a qualified
service dealer who maintains records of your installation date and service history.
c- An accurate description of the problem.
d- Date of failure.
2 Call the installing dealer that you purchased your second wind from.
3 If the installing dealer is unable to provide warranty parts, contact:
Call, write, fax or e-mail: Second Wind Air Purifiers
711 Park Ave.
Medina, NY 14103
1-800-387-4565 PHONE
585-798-5751 FAX
[email protected] E-Mail
WARRANTY LIMITATIONS
This warranty will be voided if the covered equipment (only second wind replacement parts
or units are warranted) is removed from the original installation site. This warranty does not
cover damage or defect resulting from:
1 Accident, or neglect or unreasonable use or operation of the equipment, including
operation of electrical equipment at voltages other than the range specified on the unit
name plate.
2 Modification, change or alteration of the equipment, except as directed by Second
Wind.
The furnishings of replacement parts under terms of this warranty will apply to the original warranty period
and will not extend the warranty.
Second Wind makes no express warranties other than the warranty specified above. All implied
warranties, including the implied warranty of merchantability and fitness for a particular purpose, are
limited to the duration of the warranty specified above. Liability for incidental and consequential
damages is excluded and is not covered by this warranty. Some States do not allow limitations on the
duration of an implied warranty or the exclusion or limitation of incidental or consequential damages,
so the limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
Second Wind shall not be liable for any default or delay in performance under this warranty caused by any
contingency beyond their control.

4
PAGE
Safety Concerns 2
Warranty 2-3
Unpacking 4
Installation Locations 5
Installation 1000 Series 6
Lamp Replacement 7
Troubleshooting 8
Replacements Parts 8
1000 Series Cut Sheet 9
1000 Series Cut Sheet 10
Your new Second Wind Air Purifier is
shipped complete in one container.
Carefully unpack the unit and all loose
items from the shipping container. Figs. 2
illustrate the unit and all loose items
packed with the unit.
1 Unit
2 Warning Labels
3 Installation Manual
4 Metal template and mounting plate
5 Cord
6 Business Reply Card
1
2
3
4
6
5

5
The Second Wind Air Purifier has been tested effective in the destruction and reduction
of bacteria, viruses and fungus under various conditions. The effectiveness of this device
may vary depending upon room area and rate of circulation. The health aspects associated
with this product were not investigated by U.L.
WARNING!!!
DO NOT LOOK AT THE ULTRA-VIOLET LIGHT
DO NOT OPERATE UNTIL IT IS INSTALLED IN THE RETURN OR SUPPLY.
TO DETERMINE AN INSTALLATION LOCATION SEE: FIG.3

6
1 Using the metal template/mounting bracket
pencil out rectangle to cut out. (Fig.4)
2 Using the drill with a 1/2 inch drill bit drill a
hole along the inside of the marked circle.
(Fig.5)
3 Then using tinsnips cut out the rectangle
(Fig.6).
4 Make sure lamps on the 1000 series units are
pointed in the direction of the airflow. There
are arrows pointing to the direction the air must
pass across the lamps. If not remove the lamps
from the brackets and turn them around.
5 Install mounting plate around opening in duct
with zip screws. (Fig.7)
6 Use the self tapping sheet metal screws to
secure the unit to mounting template. (Fig.8)
7 Make sure the power is off to the blower be-
fore wiring unit.
8 With the switch in the off position wire the unit
direct to a 120/240 vac blower, the EAC termi-
nal or use pressure switch, sail switch. Turn the
switch to the on position.
9 The air purifier is designed to turn on and off
with the forced air blower. (Fig.9) If lamp is
operating the sight glass will illuminate. If it is
not see the troubleshooting section.
• Installation should be done by a qualified HVAC contractor.
• Read all safety instructions at the beginning of this manual.
• Make sure unit is installed so that the UV light can not be seen directly through any returns
or supplies.
• Units should not be installed with in 12-18 inches of any non UV resistant materials. If ma-
terials are in question call manufacturer of said products to see if they are made with UV
inhibitors. Prolonged UV exposure will degrade non UV resistant materials. Non UV resis-
tant materials must be shaded or covered .
1 Marker
2 Tinsnips
3 Drill
4 Drill Bits
5 5/16” &
11/32 “Nut
driver
6 Tape
Measure
7 Metal
Template
and
Mounting
Bracket

7
Second Wind Air Purifier lamps are designed to be on all the time. After approximately 9000-11000 hours of
operation the lamps intensity will decrease. Installation of a replacement lamp is best handled by a HVAC
Contractor.
1 Turn unit off and make sure the power is off
to the unit.
After lamp has cooled proceed.
2 Remove screws from around the unit, do not
remove the screws from the hinge. (Fig.13)
3 Drop unit down, it will remain attached to the
duct via the hinge. (Fig.14)
4 Carefully remove lamp from brass lamp hold-
ers. (Fig.15)
5 Remove lamp connector from end of lamp.
(Fig.16 & Fig.17)
6 Install new lamp into socket and snap into
brass holders.
7 Return unit to upright position against duct
and re-attach with screws.
8 Power unit up and turn on.
NOTE
UV Lamps contain mercury like other
fluorescent lamps and must be disposed of
properly. Do not throw old lamps in the
trash. Contact your local waste collection
agency for proper disposal procedures.
If the lamps are dirty or have fingerprints
on them, use alcohol to remove.

8
1 Make sure that the unit is wired properly and
is turned on.
2 Check the on/off switch to make sure it is
on.
3 If the lamp is still not on, switch the unit
off, disconnect power and check the fuse.
4 Make sure the lamp is not broken and that
it is in the socket.
5 If the lamp is still not on check the ballast
1000ka and 1000kcs.
• Check the input power by testing the
outlet for 120 VAC.
• Then test the resistance of the ballast .
Disconnect the power cord. Measure the
resistance from the black lead on the input
side of the ballast to the blue lead on the
output side of the ballast. To contact the
blue lead you may need to remove the
lamp and put the multi-meter probe into
the corresponding socket opening. The
resistance should be 7-12 ohms. If the
resistance is less than 7 ohms, replace the
ballast.
• For the 120 vac ballast (#SSGPH287P)
measure the resistance the same as above.
The ohms should be 16-30 ohms, if the
ohms are below16 ohms replace the bal-
last.
Replacement Parts
1 Ballast 240 vac 1056
1 Ballast 120 vac 1059
2 Interlock Switch 1050
3 On/Off Switch 120 V 1061
On/Off switch 240 V 1057
4 Fuse Assembly 1054
5 Fuse 1055
6 Power Cord 1124
7 Lamp Connector 1014
8 9 “ Lamp 1000-1001 1068
9 Brass lamp holder 1013
10 Sight Glass 1078
11 18 “ Lamp 1002kcs 1067
• For the 240 vac units 1001ka, 1001kcs and
1002kcs the ballast resistance should be
tested like before.
Disconnect power. For the 240 vac ballast
(#SSGPH28746RC) the resistance should
be 35-45 ohms. If below 35 ohms replace
the ballast.
• If everything else has been checked and
is fine, but the lamp is still out, the
ballast starter is blown and the ballast
should be replaced.

9
Since the first ultraviolet irradiation
system was used successfully in 1909,
ultraviolet irradiation has had a 94 year
performance history. Second Wind
uses the ultraviolet wavelength at
253.7nm, ultraviolet radiation lethal to
microorganisms. Second wind air
purifiers can reduce mold, bacterial, or
viral airborne microbes in all areas of a
Heating Ventilation and Air
Conditioning system (HVAC).
Second Wind air purifiers can also
address Volatile Organic Compounds
(VOC's), through the addition of
Singlet oxygen molecules (O1).
Singlet oxygen in this case is achieved
by the use of our high intensity
ultraviolet lamps There are two differ-
ent wavelengths of light that work to-
gether to produce singlet oxygen . Gas
contaminates are oxidized in a reaction
that takes place with the singlet oxy-
gen, changing the contaminates
molecular structure.
The Second Wind Purifier is the perfect choice for
small or large applications . Second Wind uses
ultraviolet germicidal light and singlet oxygen
process to disinfect mold, bacteria, infectious
disease, and decrease volatile organic compounds
in the air stream. Second Wind air purifiers are
designed for surface and air disinfection.
Features and Benefits
• Available for all applications
• Disinfects mold
• Inexpensive to operate
• Surface and Air Indoor Air Quality Control
• Proven effectiveness through independent test
data
• High intensity Ultraviolet Lamps
• Singlet oxygen process to reduce VOC levels
• 1 year lamp warranty
• Over 9000 hours lamp expectancy
• Electronic start power supply ranges from
110/277 VAC
• Registered as a Class II medical device
#k980745
• Registered with the EPA #73112

10
Second Wind Air Purification 1000KA,
1000KCS, 1001KA, 1001KCS and 1002KCS
units are mounted in the return to
accommodate most HVAC systems. The units
install anywhere in the system to disinfect
molds, bacteria or reduce VOC
contamination. The housing is steel and
comes in 2 sizes (9” and 18” lamps). All units
are manufacturer assembled and tested.
Models 1001KA, 1001KCS and 1002KCS:
The power source is a electronic, Class P,
Sound rated A, Type HL, NO PCB’s, type 1
outdoor ballast meeting EMI requirements of
CFR Title 47 Part 18 consumer. The
operating range is 240VAC and the current is
425ma@240vac. The ballast is designed to
operate at any airflow and relative humidity.
Models 1000KA and 1000KCS:
The power source is a electronic, Class P,
Sound rated A, Type HL, NO PCB’s, type 1
outdoor ballast meeting EMI requirements of
CFR Title 47 Part 18 consumer. The
operating range is 120 VAC and the current is
425ma@120vac. The ballast is designed to
operate at any airflow and relative humidity.
Second Wind lamps operate at 253.7 nm,
ideal for air disinfection, good for use at any
velocities, temperatures ranging from 30 -
170 F. Every lamp has an extended lamp life
coating which helps maintain intensity levels
at 85% even after a year of operation. They
are a High Output (HO), T5 (15mm)
diameter, lamp yielding 2/3 more output than
standard lamps of the same length. Base of
the type “L” quartz glass is ceramic, with
triple-coiled electrodes made of
molybdendum lead in a clamped filament
design. Lamp connectors are 4-pin single
ended circling sockets. Lamp life shall not be
less than 9000 hours.
Submitted device shall be tested under typical HVAC
conditions and in accordance with the general provisions
of IES Lighting Handbook, 1981 applications Volume.
Total output per one inch arc length shall be not less
than 10uW/cm2 at 1 meter in air of 45 F and 400 fpm
Dimensions:
1000KA - 6”W x 3.25” H x 14”L x 1-9” Lamps
1000KCS- 6”W x 3.25” H x 14”L x 2-9” Lamps
1001KA - 6”W x 3.25” H x 14”L x 1-9” Lamps
1001KCS - 6”W x 3.25” H x 14”L x 2-9” Lamps
1002KCS - 6”W x 3.25”D x 23”L x 2-18” Lamps
Weight
1000KA - 5 lbs.
1000KCS - 6 lbs.
1001KA - 6 lbs
1001KCS - 7 lbs.
1002KCS - 10 lbs.
Power Electronic Ballast
1000KA: 120 VAC
1000KCS: 120 VAC
1001KA: 240 VAC
1001KCS: 240 VAC
1002KCS: 240 VAC
Lamps
18” 9”
Base Face in. - 17.2 8.4
Length mm - 436.0 212.0
Arc Length in.- 14.2 5.2
mm - 360 131
Current mA- 425 425
Wattage W- 40 25
Voltage @60Hz- 86 32
UV Output W- 10 5
UV Output @1M
uW/cm2 - 75 35
Lamp life hours- 9000 9000
Wiring
Number 18 teflon coated wire 600V, 105C.
Warranty
3-Years Fixture 1-Year Lamps
DEALER IMPRINT: