Securefast SBL340 User manual

T/049A/SBL340
5th January 2017
SBL340
Installation Instructions for SBL340 Push Button Lock with Deadbolt
This lock has been Fire Tested in accordance with BS EN1634-1 with the use of Intumescent Seals.
Installation
Applying the Template
Correctly position and tape the template, T/048/SBL340, to the internal door face, at the desired
height from the floor level. Ensure that the marked door edge on template is correctly aligned with
actual door edge. (Figure 1)
Mark the 10mm diameter hole for the spindle of the Digital Lock, the two 7mm holes for the bolt
through fixings.
Drill all marked holes.
Handing Digital Lock
IMPORTANT: Firstly determine handing of the door. When viewed from the outside, your door is right handed if the hinges are on
the right and left handed if the hinges are on left.
NOTE: The Knob on the external Keypad Digital Lock will rotate freely in one direction and require the inputting of the code to
rotate in the other direction; this is allows the deadbolt to be thrown from the outside
without a code entry but not withdrawn.
Remove the cover held in place by 2 blue screws.
With Tweesers remove the metal pin and put in the other visible hole to change
handing.
Replace cover and secure using blue screws.
The metal pin will only locate in the back of the digital lock unit properly if the follower
is in the correct orientation (as shown in the images on the right).
If you do not reinsert the metal pin in to either of the holes then the deadbolt can be
thrown and withdrawn from the outside without the entry of a correct code.
Positioning of Spindle
The spindle is designed for doors 35 to 65 mm thick. Therefore shorten, if
necessary, to suit door thickness
When inserting the spindle correctly locate it into the reverse of the Digital
Lock with consideration to the handing of the door. (Figure 4)
Fixing the Lock
IMPORTANT: Do not close the door before confirming that the code and lock is functioning correctly.
If necessary, shorten the fixing bolts in order to suit the thickness of the door
When shortening the fixing bolts allow at least 4/5 threads to screw into the lock case
Figure 1
Figure 4
Door edge
BEFORE INSTALLATION
PLEASE:
1) Ensure all parts work
properly
2) Check and Ensure the
supplied Code works. If you
wish to change the code follow
the instructions under
‘Changing the Code’ and
confirm at it works.
3) Ensure that both knob
handles of the Digital Lock can
be moved freely. Also check
that the deadbolt moves freely
by throwing and withdrawing it
using the knob on the internal
block.
LIST OF PARTS
1) Digital Lock with Knob
Handle
2) Internal Block with
Deadbolt
3) Neoprene Seals x 2
4) Spindle
5) Mortice Keeper
6) Surface Mounted Keeper
7) Wood screws x 2 (For
securing Keeper)
8) Tweesers (For changing the
Code)
9) Fixing Bolts x 3 (1 spare)
10) Spare Code Tumblers
11) Code Card

T/049A/SBL340
5th January 2017
SBL340
Locate the rubber seal behind the Digital Lock and using the fixing bolts secure the top and bottom of the Lock to the
door.
Before final tightening ensure the Lock is vertical and test mechanism to ensure that it is moving freely.
Do not excessively tighten the Lock and seals to the door as it could damage the operation of the mechanism.
Applying the Intumescent Seals
IMPORTANT: In order for this unit to maintain its fire rating status and be suitable to be installed on a fire rated door Intumescent
Seals must be used. A 2mm self-adhesive mono-ammonium phosphate (Interdens) intumescent seal is recommended.
The intumescent seal need only to be fitted if morticing the keeper in to the door frame.
Using the intumescent seal affix one 2mm intumescent layer behind the rear of the striker prior to installation.
Fixing Keeper
NOTE: Firstly, determine which keeper will best suit your frame and fitting. Generally, surface
mounted keepers are best used for in swinging doors and mortice keepers for out swinging doors.
Once you have determined which keeper will suit your installation. Position it on the
frame so that it is in line with the deadbolt; ensuring there is sufficient engagement.
If fixing a surface mounted keeper simply mark the positioning of the fixing holes. Drill
the holes and secure using wood screws supplied. (Figure 5.1)
Fix the keeper with one screw first. Test the Lock to see if it works and is latching and
locking correctly. If not proceed with any necessary adjustments before securing
completely.
If no adjustments are to be made completely secure keeper with second screw.
If fixing a mortice keeper, draw around the outside profile and mark the two fixing holes.
(Figure 5.2)
Remove the keeper and cut a 1mm rebate to allow it to sit flush within the door frame.
Drill or cut a recess, at the correct position, to allow the back of the keeper to sit within
the frame.
Drill the two, marked, holes for securing keeper
Fix the keeper with one screw first. Test the Lock to see if it works and is latching and locking correctly. If not proceed
with any necessary adjustments before securing completely
If no adjustments are to be made completely secure keeper with second screw.
Changing the Code
IMPORTANT: Keep the Lock on a flat surface at all times when removing the plate to gain access as there are a lot of small
components inside. You should NEVER remove the ‘C’ tumbler.
On the reverse of the Digital Lock remove the 4 screws retaining the metal plate.
There are 5 Red Keyed tumblers, 8 Blue Keyless tumblers and 1 Clear tumbler (‘C’ Button).
NOTE: With the spare tumblers you can either increase the number of digits in the code to 6 or 7 or decrease to
3.
Press the ‘C’ button and hold it at all times during the process; using the tweezers you can remove one or more of the
keyed & keyless tumblers.
Re-insert the tumblers (putting the Blue tumblers in the slots corresponding with the buttons you do not wish to use and
the Red in those you do wish to use) to produce the desired code.
NOTE: The keyed and keyless tumblers vary in shape therefore it is essential that they are reinserted in the
correct orientation as shown below in Figure 5.
Once the tumblers are refitted make a note of the new code and replace and secure the metal plate with the 4 screws.
Check the code functions before refitting to the door.
Figure 5