Securam FPC-0601A-D22 User manual

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 1
Document No.: FPC0601AD22
Version No.:201222
ScanLogic D22
Model: FPC-0601A-D22
Biometric Safe Lock System
Operation Guide

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 2
Table of Contents
Section 1.0 Enroll the first fingerprint
Section 1.1 Unlocking the ScanLogic D22 – Lock Operation
Section 2.0 Enroll the second fingerprint
Section 3.0 Enroll additional fingerprints
Section 4.0 Set/Change User Code
Section 5.0 Enable User Code
Section 6.0 Disable User Code
Section 7.0 Disable User
Section 8.0 Enable User
Section 9.0 Set Time Delay
Section 9.1 Set Time Delay Override User
Section 9.2 Duress Time Delay
Section 9.3 Time Delay: Unlock with an enrolled fingerprint or code
Section 10.0 Set Number of Locks
Section 10.1 Authorize Access to Locks
Section 10.2 Enable Sequence
Section 11.0 Delete One User
Section 12.0 Delete All Users
Section 13.0 Dual Mode
Section 14.0 Penalty Time -Wrong Code Entry
Section 15.0 DayLight Savings Time
Section 16.0 Maximum Door Open Time
Section 17.0 View Audit Trail
Section 18.0 Set ID01 to Master
Section 19.0 System Info
Section 20.0 Set Security Level

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 3
Section 21.1 Enroll the first fingerprint and its bound code (Level Section 2)
Section 21.2 Enroll the second or additional fingerprints and its bound code (Level 2)
Section 22.0 Set/Change the first code (Level 1)
Section 22.1 Enroll the second or additional codes (Level 1)
Section 23.0 Disable / Enable User (Level 1 & 2)
Section 24.0 Set Time Delay (Level 1 & 2)
Section 25.0 Unlock with an enrolled code (Level 1 & 2)
Section 26.0 Set Number of Locks (Level 1 & 2)
Section 26.1 Authorize access to Locks (Level 1 & 2)
Section 26.2 Enable Sequence (Level 1 & 2)
Section 27.0 Delete One User / All Users (Level 1 & 2)
Section 28.0 Dual Mode (Level 1 & 2)
Section 29.0 Penalty Time -Wrong code entry penalty (Level 1 & 2)
Section 30.0 DayLight Savings Time (Level 1 & 2)
Section 31.0 Maximum Door Open Time (Level 1 & 2)
Section 32.0 View Audit Trail (Level 1 & 2)
Section 33.0 System Info (Level 1 & 2)










SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 4
About Security Level Classifications
The ScanLogic D22 can operate in three different security levels as follows:
 Level 1: EntryPad can be operated by a code only.
 Level 2: EntryPad must be operated by a fingerprint and the code associated with that
enrolled fingerprint (“bound code”).
 Level 3: EntryPad can be operated by a fingerprint or a code.
Note:
All enrolled users will be deleted when security level is changed. The first code (ID No. 01) will be
set to default 123456.
Factory default security level is Level 3.
Battery Replacement Instructions
1) On the back of EntryPad, you will see one 9V alkaline battery. Take the battery out of the battery
compartment.
2) Gently remove the connector by unsnapping it from the two terminals on the top of the battery.
Never Pull on the Battery Leads.
3) Connect a new 9V alkaline battery to the battery clip.
4) Put the battery and the leads completely back into the battery compartment.
For mounting and wiring information refer to the installation instructions.

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 5
1.0 Enrolling the first fingerprint (Security Level 3)
Step 1: Install a brand new 9V alkaline battery in the ScanLogic D22 EntryPad.
Step 2: Place your finger on the fingerprint scanner, the LCD screen will show “Welcome” and then
“Set Time/Date”. Set the correct time and date using the UP and Down arrows keys and OK button.
Once set the LCD screen will show “Start Enrolling First User”.
Step 3: After the screen shows “Place Finger”, place your finger on the fingerprint scanner and
hold.
Step 4: Hold your finger on the scanner until the above displays finish one by one.
Upon completion, the first fingerprint with an ID No. 01 is enrolled successfully.
1.1 Unlocking the ScanLogic D22 (Security Level 3)
Step 1: Place enrolled fingerprint on the scanner.
Step 2: After enrolled fingerprint is verified successfully, the safe lock will unlock.
2.0 Enroll the second fingerprint (Level 3)
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place the enrolled finger of ID01 on the scanner and hold.
Step 4: After ID01 fingerprint is verified successfully, press “▲” or “▼” to select “Enroll New User”.

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 6
Step 5: Press “Menu/OK” again.
Step 6: Place the second enrollee’s finger (different from the first one) on the fingerprint scanner
and hold.
The second fingerprint, with an ID No. 02, is enrolled successfully.
Note: ID No. 01 and ID No. 02 are administrators.
3.0 Enroll additional fingerprints (Security Level 3)
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.
Step 4: After the fingerprint is verified successfully, the LCD screen shows: “Select Menu”, press
“▲” or “▼” to select “Enroll New User”.
Step 5: Follow the Steps 5 and 6 in Section 2.0 to enroll additional fingerprints.
4.0 Set/Change User Code (Level 3)
The ScanLogic D22 is capable or registering not only fingerprints but also 6 digit codes for each
enrolled fingerprint. To Set or Change a User code, perform the following process:
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”, press “Menu/OK” again.
Step 3: Place the user’s finger on the fingerprint scanner and hold.
Step 4: After the fingerprint is verified, press “▲” or “▼” to select “Set/Change User Code”, press

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 7
“Menu/Ok”.
Step 5: When the screen displays “New Code”, enter a 6 digit code.
Step 6: Enter the same 6 digit code again.
The new code is now set or changed successfully.
Note:
● Administrators’ code can be set or changed directly.
● Non-administrators’ code must be enabled by the administrator first, then, the user can set or
change their code.
● If consecutive four digits of a new code (for example 512341) is the same as one of the enrolled
codes (612345) , LCD screen will show : “Code is similar” and the code will not be accepted.
Enter a different code for this User.
5.0 Enable User Code (Security Level 3)
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.
Step 4: After the fingerprint is verified successfully, press “▲” or “▼” to select “Enable User Code”,
press “Menu/Ok”.
Step 5: The screen will display “ID:03 Code Enable?”, press “▲” or “▼” to select the desired ID
No. to be enabled.

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 8
Step 6: When the desired ID No. is visible on the screen, press “Menu/Ok” to select.
This User ID will now have the ability to have a code in addition to an enrolled fingerprint.
Important: The User must now set his own code using his enrolled fingerprint.
Step 7: Press “Menu/Ok”, press “▲” or “▼” to select “System Menu”. Enter the System Menu
with the User’s fingerprint (in this example using the fingerprint of ID No.3).
Step 8: Press “▲” or “▼” to select “Set/Change User Code”.
Step 9: Enter a unique 6 digit code.
Step 10: Enter the same 6 digit code.
When the LCD screen displays: “ID:03 Code Saved”, the code of ID:03 has been set successfully .
Note:
If consecutive four digits of a new code (for example 512341) is the same as one of the enrolled
codes (612345) , LCD screen will show: “Code is similar” and the code will not be accepted. Enter
a different code for this User.
6.0 Disable User Code (Security Level 3)
If a User has previously had a code enabled for use, this function will Disable the code.
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 9
Step 4: After the fingerprint is verified successfully, press “▲” or “▼” to select “Disable User Code”,
press “Menu/Ok”.
Step 5: Press “▲” or “▼” to select the desired user ID to be disabled.
Step 6: Press “Menu/Ok”
ID No.3’s code disabled.
Note: This function only disables the user’s code, not the user. The user can still unlock the door by
fingerprint.
7.0 Disable User (Security Level 3)
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.
Step 4: After the fingerprint is verified successfully, press “▲” or “▼” to select “Disable User”.
Step 5: Press “▲” or “▼” to select the desired ID No. to disable (e.g. ID 03).
Step 6: Press “Menu/OK”.
The LCD screen displays: “ID:03 Disabled”, confirming that ID 03 has been successfully disabled.
This User’s fingerprint and code have now been disabled. If the User attempts to access the lock,
the screen will display “ID:03 Disabled”.
Note: Administrators cannot be disabled.
8.0 Enable User (Security Level 3)
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.
Step 4: After the fingerprint is verified successfully, press “▲” or “▼” to select “Enable User”.

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 10
Step 5: Press “Menu/OK”.
Step 6: Press “▲” or “▼” to select the ID No. to be enabled (e.g. ID 03).
Step 7: Press “Menu/OK”.
The User ID No. 03 is now enabled and can use the previously registered fingerprint and/or code to
access the lock.
9.0 Set Time Delay (Security Level 3)
Step1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.
Step 4: After the administrator is verified successfully, press “▲” or “▼” to select “Set/Cancel Time
Delay”.
Step 5: Press “Menu/OK”.
Step 6: Press “▲” or “▼” to set time delay (00 to 99 min). Press “Menu/OK”.

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 11
Step 7: Now set the Time Window. Press “▲” or “▼” to select the desired Time Window interval
(01 to 15 min).
Step 8: Press “Menu/OK”.
The Time Delay has now been set successfully. See Section 12.0 for Time Delay opening
operation.
Note:
 Time Delay Override: ID No.1 is a Time Delay Override Code and can unlock the lock at any
time, bypassing Time Delay.
 Additionally, a second User ID (ID01 – ID30) can be set to as a Time Delay Override Code.
 During Time Delay period, the EntryPad can be programmed but the Lock Body cannot be
unlocked.
 After the original time delay has been changed successfully, the new time delay settings will
take place after the next unlocking sequence.
 However, if the new Time Delay value is longer than the previous one, the new time delay
value will be effective during the next unlocking.
9.1 Set Time Delay Override User
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Enter the code of ID No. 00 (Super Code).
Step 4: When the LCD screen shows “Select Menu”, press “Menu/OK”.
Step 5: Press “▲” or “▼” to select “Set TDO User ID”.
Step 6: Press “Menu/OK”.
Step 7: Press “▲” or “▼” to select the User ID No.

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 12
Notes:
 If ID21 is selected, for example, the two users with TDO are: ID01 and ID21.
 Even if ID21 is set with TDO, it will not be an administrator with more functions. ID01 and ID02
are still administrators but ID02 will no longer have TDO capability.
 If you select ID01, then ID01 will be the only user with TDO.
 ID01 has TDO capability by default. However, in order to remove TDO capability from ID01,
select ID00 in the above programming sequence. This will remove TDO capability from ID01
and only ID00 will have TDO capability.
9.2 Duress Time Delay (Level 3)
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.
Step 4: After the fingerprint is verified successfully, the LCD shows “Select Menu”, press “▲” or “▼”
to select “Set Duress Time Delay”.
Step 5: Press “Menu/OK”. Press “▲” or “▼” to set the time between 0~99 minutes, press
“Menu/OK”.
Step 6: Set the “TM window”：Press “▲” or “▼” to set the time between 01~15 minutes, press
“Menu/OK”.
Note:
 TDO capability is still available to TDO Users.
 Duress code can only be set by User ID00. (The menu selection to program Duress is
“Duress Code Shift”).
9.3 Time Delay: Unlock with an enrolled fingerprint or code (Level 3)
To unlock the safe lock when Time Delay has been programmed:
For example:
Time Delay is set 10 minutes and Time Window 5 minutes.
Step 1: Place an enrolled finger (ID: 03) on the fingerprint scanner and hold until the LCD shows:

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 13
Step 2: The display will start counting up. The LCD screen flashes the expired time interval every 15
seconds.
Step 3: When Time Delay finishes counting, two beeps will sound and the LCD screen will show:
Step 4: The display will start counting down. The LCD screen flashes with remaining time every 15
seconds.
Within the next 5 minutes, a User must verify an enrolled fingerprint to unlock. The LCD will display
the ID of the verified user:
Note:
 As a default TDO User, ID 01 can unlock without time delay.
 When the EntryPad starts its Time Delay process, user can operate the EntryPad normally,
but the Lock Body will not be unlocked even if the verification is successful.
 If no valid code or enrolled fingerprint are verified successfully during Time Window period,
the Lock Body will be locked until the end, and then , the LCD will show:
10.0 Set number of locks (Security Level 3)
The ScanLogic D22 is capable of managing up to 4 Lock Bodies using a junction box (Junction box
Part# CB11-1T4). The EntryPad must be programmed to recognize the additional Lock Bodies.
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 14
Step 4: After the fingerprint is verified successfully, press “▲” or “▼” to select “Set Number of
Locks”. Press “Menu/OK”.
Step 5: The display will prompt you to enter the “Mfc. Code”. The default Mfc. Code is 975246.
Step 6: Press “▲” or “▼” to set number of locks.
Note: The default number of locks is 01. The maximum number of locks is 04.
When opening the lock, the display will ask you to select the lock to be opened, press the numbered
button that corresponds with the lock to be opened. Then, the lock will be unlocked automatically if
verification is successful.
10.1 Authorize access to locks (Level 3)
The ScanLogic D22 allows you to set the Users that will have access to specific locks.
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.
Step 4: After the fingerprint is verified successfully, press “▲” or “▼” to select “Authorize Locks”.
Step 5: Press “Menu/OK”. The system will now ask which range of Users are to be programmed
to open this set of locks.

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 15
Step 6: Press “▲” or “▼” to set the first ID in the group of users to be authorized. Press “Menu/OK”.
Step 7: Press “▲” or “▼” to set the last ID in the group of users to be authorized. Press “Menu/OK”.
The example shows how to authorize users with ID No. from 03 to 05.
“Lock 1234” means the number for each lock. “Auth. oxxx” shows whether the group has
authorization for each specified lock. Letter “o” means the group has authorization to open this lock.
Letter “x” means the group does not have authorization.
For example: To authorize users with ID No. 03, 04 and 05 to open Lock 2, when the LCD screen
shows:
Press “1” to change “o” to “x”.
Press “2” to change “x” to “o”. Press “Menu/OK”.
Now, the authorization is completed.
Note: Administrators can open all locks without authorization.
10.2 Enable sequence (Security Level 3)
The ScanLogic D22 allows you to set up sequencing when multiple locks are present. This means

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 16
that you can program the system such that Lock #1 is known to be the Outer (or Main) door on the
safe. With Sequencing enabled, if a User is authorized to open Lock#2, the system would know to
first open Lock#1 and then 5 seconds later it will automatically open Lock #2.
(This eliminates the need to Open Lock#1, and then enter your code again to open Lock#2).
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.
Step 4: After the fingerprint is verified successfully, the LCD screen shows “Select Menu”. Press
“▲” or “▼”to select “Enable Sequence”. Press “Menu/OK”.
If the number of Locks is more than one, when unlocking in sequence is enabled:
Press “1”, Lock 1 will be unlocked;
If you press a number which is >1 (for example 3), Lock 1 will open first and then Lock 3 will open 5
seconds later.
11.0 Delete One User (Security Level 3)
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.
Step 4: After the fingerprint is verified successfully, press “▲” or “▼” to select “Delete One User”.
Press “Menu/OK”.
Step 5: The system will automatically select the first enrolled User. Press “▲” or “▼” to select the
User ID to be deleted. Press “Menu/OK” to confirm.
Step 6: The system will confirm the user has been deleted as follows:

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 17
Note : If User ID 01 is Set to Master, User ID 02 cannot delete User ID 01.
12.0 Delete All Users (Security Level 3)
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.
Step 4: After the fingerprint is verified successfully, press “▲” or “▼” to select “Delete All Users”.
Press “Menu/OK”. The following message will be displayed:
Step 5: Press “Menu/OK” to confirm..
The system starts deleting users from ID No. 01 to ID No. 30; and then confirms the deletion as
below:
▪▪▪▪▪▪
Note1: After deleting all users, all the enrolled fingerprints and codes are deleted completely.
Note2: If User ID 01 is Set to Master, User ID 02 cannot delete all users.
13.0 Dual Mode (Security Level 3)
Step 1: Press “Menu/OK”. The screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.
Step 4: After the fingerprint is verified successfully, press “▲” or “▼” to select “Enable Dual Mode”.
Press “Menu/OK.

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 18
Step 5: The LCD will display the following message confirming that Dual Mode is now enabled:
Note:
 Dual Mode Override: In dual mode, administrator’s fingerprints or codes (ID No. 01 or 02) are
Dual Mode Override Codes and can unlock the Lock Body without the need for a second code
to be entered.
 Only administrators’ fingerprints or codes can be used to change Dual Mode to single user
mode.
 In order to open the lock in Dual Mode, the second code or fingerprint must be entered within
60 seconds after the first code is successfully verified.
 If all users are deleted, Dual Mode will be disabled automatically.
14.0 Penalty Time –Wrong Code Entry (Security Level 3)
Penalty time is a function that prevents someone from opening your safe lock by trying to guess
codes.
Four (4) consecutive invalid code entries initiate a 4-minute penalty time period with the LCD
showing:
The EntryPad is shut down and no operation is permitted.
Then, the EntryPad will start counting down with the LCD flashing the remaining time every 15
seconds. e.g.
After the countdown is finished, the EntryPad is ready to use again.
Note: Two more consecutive invalid codes will restart an additional 4 minutes delay period. An

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 19
attempt to unlock by an enrolled fingerprint will not terminate the penalty time period.
15.0 Day Light Saving (Security Level 3)
Step 1: Press “Menu/OK”, the screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.
Step 4: After the fingerprint is verified successfully, press “▲” or “▼” to select “Day Light Saving
TM”. Press “Menu/OK” again.
Step 5: Press “▲” or “▼” to select “Y” or “N”. If selecting “Y”, this function will be enabled. If
selecting “N”, this function will be disabled.
Step 6: Then, press “▲” or “▼” to select the “Start Month”
Step 7: Select the “Start Week”
Step 8: Select the “Start Time”
Step 9: Select the “End Month”

SECURAM Systems Inc. ScanLogic D22 Operation Guide Page 20
Step 10: Select the “End Week”
Step 11: Select the “End Time”
For example: If you live in North America, you can select
 “Start Month”: 03
 “Start Week”: 02
 “Start Time”: 02
 “End Month”: 11
 “End Week”: 01
 “End Time”: 02
This function will start at 2:00am on second Sunday of March and end at 2:00 on first Sunday of
November.
Note: Users can set “Day Light Saving” according to their certain condition.
16.0 Maximum Door Open Time (Security Level 3)
Step 1: Press “Menu/OK”, the screen will show “Select Menu”.
Step 2: Press “▲” or “▼” to select “System Menu”. Press “Menu/OK” again.
Step 3: Place an enrolled administrator’s finger (ID No. 01 or 02) on the scanner and hold.
Step 4: After the fingerprint is verified successfully, press “▲” or “▼” to select “Max. Door Open
Time”. Press “Menu/ OK” again.