Sedus match User manual

G Adjusting the basic a m ests (optional)
®Height: 1. Press the button underneath the armrest, lift or lower the
armrest 2. Release the button, the armrest locks into place
®Ad ustable seat width: 1. Loosen the screws slightly with a Torx
key (TX40) 2. Position the armrests 3. Retighten the screws
H Adjusting the 3D a m ests (optional)
®Height: 1. Press the button, lift or lower the armrest 2. Release the
button to engage the armrest
®Depth: Push the armrest cover backwards or forwards to engage
®Swivelling armrest covers: up to 15°inwards and outwards; also swivels
360°with more force; a 180°turn changes the width between the armrests
®Ad ustable seat width: 1. Loosen the screws slightly with a Torx
key (TX40) 2. Position the armrests 3. Retighten the screws
A Height of the seat
®Lowering the seat: 1.Sit down on the seat 2.Pull the lever upwards
(the seat will drop slowly) 3. Releasing the lever at the desired height
will lock the position
®Raising the seat: 1. Stand up 2. Pull the lever upwards (the seat will
rise slowly) 3. Releasing the lever at the desired height will lock the
position
C Angle of the back est
®Ad usting the backrest dynamically: 1. Pull the lever upwards and
release it 2.Lean against the backrest 3.The backrest is free-flowing
®Locking the backrest into position: 1. Lean back until the backrest
reaches the desired angle 2. Press the lever down and release it to
lock the backrest into position
B Height of the lumba suppo t (optional)
®Ad usting the height: 1. Do not lean against the backrest
2.Ad ust the handles on both sides to the desired height
D St ength of the back est p essu e
®1.Ad usting the backrest dynamically (C) 2.Exert only slight pressure
on the seat and backrest 3. Crank the quick ad ustment mechanism
downwards until the desired position is achieved (greater backrest
pressure) or upwards (lesser backrest pressure)
E Depth of the seat (optional)
®1. Press the finger plate and hold it fast 2. Push the cushion to the
desired position 3. Release the finger plate, and the seat will engage
F Seat angle (optional)
®1. Stand up 2. Swivel the lever backwards and lock into place (chair tilts
4° forwards) or swivel downwards and lock into place (seat moves back
into its original position)
Congratulations! You have chosen a high-quality Sedus product. We hope you en oy
your match office swivel chair.
Please read the following information on ad usting the chair properly so that you can
en oy all the ergonomic advantages match has to offer.
match
Instructions for use
A
C
BB
E
D
F
H
G
The functions of the swivel chair

Co ect use
This office swivel chair is designed for a user weight of up to 110 kg and may only
be used for the purpose intended while exercising due care and attention. Using it
inappropriately (e.g. as a stepladder, sitting on the armrests or placing extreme
weight on one side) could result in accidents.
Casto s
Please remove the red or blue transport protection before using the product for the
first time. Different castors are available, for the sake of your safety and for use on
different types of flooring in accordance with safety regulations: Hard castors for
soft floors (standard). Soft castors for hard floors are optional. Changing castors:
this might be necessary, for instance, after moving office, or after the installation
of a new floor surface – simply pull out the castors and push new ones in.
A m ests
Armrests can be fitted later or exchanged on some models.
Plastic pa ts
Soapy water is suitable for cleaning. Please do not use any aggressive cleaning
materials.
Upholste y
In the case of light soiling to the upholstery, please only use suitable mild detergents
or Sedus cleaning agents. The upholstery should only be changed by skilled persons.
Leathe
Leather is a natural product, whose markings give the material its unmistakable
character. Rub off light soiling with a soft woollen cloth. Heavier soiling should only
be treated with cleaners designed for aniline-dyed leather. Do not expose semi-aniline
leather to direct sunshine.
Se vicing
Servicing work, such as exchanging or working on the gas-lifts, may only be carried
out by trained personnel.
®Use the whole seat a ea
The anatomically shaped seat should be fully occupied. Only
then is proper contact with the supporting backrest assured.
match is also available with an ad ustable seat tilt and a sliding
seat. These allow the seat to be ad usted to suit any body size.
®Adjust the height of the seat p ecisely
The correct seat height means that your elbow oint adopts an
angle of about 90° when your forearms are resting horizontally
on the desktop. Your knee oint will also adopt an angle of
about 90° when your feet are flat on the floor. If your desktop
is too high, and cannot be lowered to a correct position, you
need a footrest with ad ustable height and tilt.
®Adjust the back est
Ad ust the height of the lumbar support so that the curvature
of the backrest supports the spine in the region of the third
and fourth lumbar vertebrae (where the forward curvature is
greatest). This stabilises the natural S-shape of the spine in
every sitting position.
®Dynamic sitting
Dynamic sitting means changing your sitting posture frequently,
or in other words shifting as often as possible between the
front and rear sitting posture. You should therefore ad ust the
backrest dynamically. match is fitted with a “Similar”mechanism,
which allows you to ad ust the pressure of the backrest individ-
ually. This ensures that the backrest and seat automatically
give your body support in every sitting/lying position.
Healthy sitting is a question of attitude
02.2012
User notes
Deutschland: Sedus Stoll Aktiengesellschaft, Brückenstraße 15, D-79761 Waldshut
Telefon [phone], Telefax (07751) 84-310, [email protected], www.sedus.de
Belgien: B-9230 Wetteren, Telefon [phone], www.sedus.be
F ank eich: F-75009 Paris, Telefon [phone], www.sedus.fr
G oßb itannien: London EC1V 4DU, Telefon [phone], www.sedus.co.uk
Italien: I-22071 Cadorago (CO), Telefon 031.494.111, www.sedus.it
Niede lande: NL-2718 SZ Zoetermeer, Telefon [phone], www.sedus.nl
Öste eich: A-5301 Eugendorf, Telefon [phone], www.sedus.at
Schweiz: CH-4613 Rickenbach, Telefon [phone], www.sedus.ch
Spanien: E-28830 San Fernando de Henares, Telefon [phone], www.sedus.es
Sedus contact addresses