real living FP-P-1915-21 User manual

1. Need at least two adults to assemble this fireplace.
2. Assemble on soft , smooth surface to protect finish from being scratched.
3. DO NOT use power tools.
4. Remove all packaging material, make sure all parts are present before assembly.
5. Estimated Assembly Time: 1 hour 15 minutes. Exact assembly times will vary based on skill level and
past assembly experience.
6. Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote
control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result
the furnishing may tip over on to the child.
7. Relocating audio and/or video equipment to furniture not specifically designed to support audio and/or video
equipment may result in death or serious injury due to the furnishing collapsing or over turning onto a child.
8. To prevent serious injury or death, this product is equipped with a wall anchoring system. Before this product
can be used, the wall anchoring system must be installed as directed in the assembly instructions.
Read all instructions before starting
Clear a flat covered space to begin
We recommend 2 adults for assembly
Note that hardware required is provided for every step
Pay attention to orientation
Letter of the part corresponds to a sticker on the product
Number of the hardware corresponds to its number in the package
Helpful hints provided along the way
GENERAL BEST PRACTICES FOR ASSEMBLY
WARNINGS
MAINTENANCE
1. Clean periodically by wiping the product with a soft clean cloth.
2. Do not expose your product to any liquids. All liquids should be wiped up immediately with a soft, slightly
damp cloth in the direction of wood grain.
3. Do not expose your product to strong or direct sunlight, near heat outlets or air conditioning units, open
windows or dampness. Excessive exposure to sunlight and heat can cause fading of your furniture finish.
Extreme temperatures and humidity changes can cause wood cracking and splitting.
4. Clean using a glass/mirror cleaner and soft cloth. Do not use cleaning products containing abrasives,
as these will scratch glass/mirror.
!

TELEVISION
MAXIMUM FLAT PANEL: 54”
MAXIMUM LOAD: 60 POUNDS
BASE
MAXIMUM LOAD: 25 POUNDS
WARNING
!
MANUFACTURER: YOUNG CHAIN CO.,LTD
ITEM#: FP-P-1915-21/ FP-P-1915-21-3A
DISTRIBUTION: Big Lots Stores, Inc.
ADDRESS: P.O. BOX 28523, COLUMBUS,OH 43228-0523
COUNTRY OF ORIGIN: VIETNAM ;
MANUFACTURE DATE: 2021.05
SMALL SHELVES
MAXIMUM LOAD: 25 POUNDS
MIDDLE SHELF
MAXIMUM LOAD: 25 POUNDS
FOR USE WITH TELEVISIONS WEIGHTING 60 LBS (27.18 KG) OR LESS.
USE WITH HEAVIER TV MAY RESULT IN INSTABILITY CAUSING TIP OVER
RESULTING IN DEATH OR SERIOUS INJURY.
CAUTION
This Fireplace (FP-P-1915-21/ FP-P-1915-21-3A) is designed for flat panel LCD TVs weighing up to 60 lbs.
For items other than flat panel LCD TVs, this fireplace will support up to 135 lbs when the item is placed evenly
on the top surface. Use with other products may results in instability causing possible injury.
!

1PC
TOP
1PC 1PC 1PC
TOP RAIL BASE MIDDLE SHELF
1PC
LEFT PARTITION
1PC 1PC 1PC
RIGHT PARTITION RIGHT SIDE PANEL LEFT SIDE PANEL
4PCS
SIDE PANEL TRIM
1PC 1PC 1PC
POST A POST B POST C
POST D
4PCS 1PC 1PC
SMALL SHELF LEFT DOOR RIGHT DOOR
1PC
MIDDLE LEG
1PC
MIDDLE BACK PANEL SIDE BACK PANEL ELECTRIC FIREPLACE
INSERT
2PCS 1PC 2PCS
PART LIST

35pcs
CAM BOLT
35pcs
CAM LOCK
31pcs
SHORT WOOD DOWEL
2pcs
KNOB
2pcs
HANDLE
3pcs
SHORT BOLT
5pcs
LONG BOLT
33pcs
ROUND HEAD SCREW
11pcs
ROUND HEAD SCREW
2pcs
DOOR BLOCK
17pcs
SHELF PIN
4pcs
DOOR HINGE
25pcs
FLAT HEAD SCREW
9pcs 1pc
GLUE
20pcs
STICKER
1pc
TOUCH-UP PEN
FLAT HEAD SCREW
HARDWARE LIST
1set
ANTI-TIPPING NOT PROVIDED

STEP 1
STEP 2
Place Post A (J), Post B (K), Post C (L) and Post D (M) on a soft smooth surface. The side with the most holes should be
facing up. Insert the Cam bolt (H1) into the corresponding hole of Post A (J), Post B (K), Post C (L) and Post D (M) using the
screwdriver (Not provided). Place a small drop of Glue (H15) into the remaining holes and insert Short wood dowels (H3). As
shown in figure 1.
Not provided
Figure 1
12pcs 8pcs
1pc
8pcs
Not provided
Figure 2
Place Side panel trim (I) on a soft smooth surface with the holes facing up.Align the holes in Right Side panel (G) with the
holes of Side panel trim (I) and secure in place with Flat head screw (H14) using the screwdriver (Not provided) as shown in
figure 2. Fully tighten all screws. Repeat this process to install Side panel trim (I) to Left side panel (H).
Assembled View:
Assembled View:

STEP 3
STEP 4
Place Right side panel (G) on a soft smooth surface with the holes facing up. Insert the Cam Bolts (H1) and Short wood
dowels (H3) of Post C (L) and Post D (M) into the corresponding holes of Right side panel (G) and secure in place using Cam
lock (H2) as shown in figure 3. Note:The blocks of Right side panel (G) should be on the side of Post D (M) and the top ends
should be flush. Repeat this process to attach Post A (J) and Post B (K) to Left side panel (H) as shown in figure 3. Note: The
Blocks of Left side panel (H) should be on the side of Post A (J) and the top ends should be flush. Insert Cam Bolt (H1) into
Right side panel (G) and Left side panel (H) as shown in figure 3 and tighten using screwdriver (Not provided). Place a small
drop of Glue (H15) into the indicated holes and insert Short wood dowels (H3) as shown in figure 3.
4pcs 12pcs
Figure 3
Not provided
1pc4pcs
Insert Cam bolt (H1) into the corresponding holes of Left & Right partition (E/F) using the screwdriver (Not provided). Place a small drop
of Glue (H15) into the remaining holes and insert Short wood dowels (H3) as shown in figure 4.
Figure 4
4pcs 4pcs
1pc
Assembled View:
Assembled View:

STEP 5
STEP 6
With assistance from another adult, hold Middle shelf (D) and Left partition (E) vertically as shown in figure 5. Slide the Cam
bolts (H1) and the Short wood dowels (H3) of Left partition (E) into the corresponding holes of Middle shelf (D) and secure in
place with Cam lock (H2) using screwdriver (Not provided). Repeat this process to attach Right partition (F) to Middle shelf
(D) as shown in figure 5. Align the Door block (H10) with the pre-drilled pilot holes in the Left partition (E) and Right partition
(F) and attach with Round head screw (H9) using screwdriver (Not provided) as shown in figure 5.
Figure 5
4pcs 4pcs
2pcs
Not provided
Insert Cam bolt (H1) into the corresponding holes of Base (C) using the screwdriver (Not provided). Place a small drop of Glue (H15) into
the remaining holes and insert Short wood dowels (H3) as shown in figure 6.
Figure 6
4pcs
Not provided
4pcs
1pc
Assembled View:
Assembled View:

STEP 7
STEP 8
With assistance from another adult, place Left side panel (H) on edge as shown in figure 7. Align the holes in Left partition (E)
and Right partition (F) with the Cam bolts (H1) and Short wood dowels (H3) in Base (C) and slide into place as shown in
figure 7. Secure the Left partition (E) and Right partition (F) to Base (C) with Cam lock (H2) using screwdriver (Not provided).
Align the Cam bolts (H1) and Short wood dowels (H3) in Left side panel (H) with the corresponding holes in Base (C) and
slide into place. Secure the Left side panel (H) to Base (C) with Cam Lock (H2) using screwdriver (Not provided). Repeat this
process for the Right side panel (G) as shown in figure 7.
8pcs
Figure 7
Not provided
Place a small drop of Glue (H15) and Insert Short wood dowel (H3) into the indicated holes of the Left side panel (H), Left
partition (E), Right partition (F) and Right side panel (G) as shown in the figure 8. Insert Middle leg (Q) into Base (C) and turn
clockwise until tight as shown in figure 8.
8pcs 1pc
Figure 8
Assembled View:
Assembled View:

STEP 9
STEP 10
Place Top (A) on a soft smooth surface with the holes facing up. Insert Cam bolt (H1) into the indicated holes in figure 9 and
fully tighten using the screwdriver (Not provided). Place a small drop of Glue (H15) and a Short wood dowel (H3) into the two
holes along the front of Top (A) as shown in figure 9. Align the holes of Top rail (B) with the corresponding Cam bolts (H1)
and Short wood dowels (H3) of Top (A) and slide into place as shown in figure 9. Secure Top rail (B) to Top (A) with Cam
lock (H2) using screwdriver (Not provided). Note: The holes for the Cam lock (H2) in Top Rail (B) should face the inside as
shown in figure 9.
Figure 9
10pcs
1pc
Not provided
8pcs
With assistance from another adult, align the Cam bolts (H1) in Top (A) with the holes in Left side panel (H), Left
partition (E), Right partition (F) and Right side panel (G) and slide into place as shown in figure 10. Secure Top (A) to
Left side panel (H), Left partition (E), Right partition (F) and Right side panel (G) with Cam lock (H2) and tighten using
screwdriver (Not provided) as shown in figure 10.
Not provided
Figure 10
Assembled View:
Assembled View:
2pcs
2pcs