SEI Colorblock HZ108100TX User manual

For assistance with assembly contact:
Southern Enterprises, Inc.
Customer Service 1-800- 33-509
[e-mail]
www.seidal.com
HZ108100TX
Colorblock Anywhere Storage
Cabinet Console – Linen
ASSEMBLY INSTRUCTIONS

A.
Quantity
of 1
top panel
B.
Quantity
of 1
bottom panel
C.
Quantity
of 1
left side panel
D.
Quantity
of 1
right side panel
E.
Quantity
of 1
center panel
F.
Quantity
of 1
middle rail
G.
Quantity
of 2
top rail
H.
Quantity
of 1
back panel
I.
Quantity
of 1
top drawer front
J.
Quantity
of 1
bottom drawer front
K.
Quantity
of 2
drawer side left
L
Quantity
of 2
drawer side right
M
Quantity
of 2
drawer back
N
Quantity
of 2
drawer bottom
o
Quantity
of 2
door panel
Colorblock Anywhere Storage Cabinet Console – Linen
Parts list
Please review all parts and hardware before disposing of any packaging.
Call customer service if you are missing hardware.
Using a screw that is too long will cause damage.
Before beginning assembly separate each type of screw. Carefully study the
diagrams below. You may receive extra hardware with your unit.
Page 2
up
drawer bottom
door panel

P
Quantity
of 4
leg
Q
Quantity
of 1
middle leg
R
Quantity
of 1
adjustable shelf
S
Quantity
of 2
bottom drawer rail
1
Quantity
of 22
wood dowel:
Dia 5/16” x 1-3/16” L
2.
Quantity
of 20
bolt: Dia 5/16” x 1” L
3
Quantity
of 24
cam bolt
4
.
Q
uantity
of 24
cam lock
5.
Quantity
of 36
screw: Dia 1/8” x 1/2” L
.
Quantity
of 26
screw: Dia 1/8” x 1/2” L
7.
Quantity
of 16
screw: Dia 1/8” x 1” L
8.
Quantity
of 2
hinge
9.
Quantity
of 3
knob
10
.
Quantity
of 3
small bolt
11
.
Quantity
of 2
magnet
Page 3

12
.
Quantity
of 1
large wood dowel
13
.
Quantity
of 4
shelf pin
14.
Quantity
of 1
allen wrench
15.
Quantity
of 4
bracket
1 .
Quantity
of 2
plastic strap
17.
Quantity
of 4
anchor
18.
Quantity
of 4
screw: Dia 1/8” x 1-3/8” L
19.
Quantity
of 4
screw: Dia 1/8” x 5/8” L
20.
Quantity
of 2
ball bearing slide
21.
Quantity
of 8
screw: Dia 1/8” x 1-1/4” L
22.
Quantity
of 20
paper cover
Care and Cleaning Instructions:
Before using wipe with a clean dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions please
call customer service at 1-800-633-5096
please call manufacturer for assistance questions
or
parts.
Assembly Tool Required No.2 Phi
Tool List: 3/1 " drill bit, drill, tape measure, and pencil.
Page 4
Assembly Tool Required No.2 Phillips
Screwdriver (Not included)

Figure 1
Assembly Instructions:
Wood may scratch easily, Be
careful when assembling. Do not
scratch.
First please separate metal slide
(20) to male metal slide and
female metal slide as shown.
To separate press down on the
lever as you pull the male and
female slides apart. Press the
lever down the opposite way if
slides don’t come apart.
Figure 2
Begin by assembling the female
ball bearing slide (20) on
vertical panel (E) with screw
(5) tighten with a screwdriver
(not included).
Tip: Make sure the open end of
the rails are facing the front of
the unit and are pointed
towards the finished edge of
panel (E).
Colorblock Anywhere Storage Cabinet
Console
–
Linen
Assembly Instructions
20
20
20
If the d raw er hits ad jo inin g p arts,yo u
can lo o sen th e screw s o n m ale slid e
an d ad ju st th e h eig h t o f d raw er
5
5

Figure 3
Then
attach another
female
ball bearing slide (20) on right
side panel (D) with screws (5)
tighten with screwdriver (not
included).
Tip: Make sure the open end of
the rails are facing the front of
the unit and are pointed
towards the finished edge of
panel (D).
F
igure
4
Insert cam locks (4) into predrilled
holes on front middle rail (F)
On panel (E) screw cam bolts (3)
into pre-drilled holes. Attach center
panel (E) to top rails (G) and middle
rail (F) with wood dowels (1) and
large wood dowel (12)
Tighten by rotating cam lock (4)
clockwise with phillips screwdriver
(not included).
Cover cam lock holes with paper
cover(22)
Attach panel (D) to top rail (G) and
middle rail (F) with wood dowels (1)
and large wood dowel (12).
Attach left side panel (C) to top rail
(G) with wood dowels (1) and large
wood dowel (12)
Figure 5
Insert cam lock (4) into predrilled
holes on pre-assembled unit.
Place dowels (1) of left/right side
panels (C, D) and center panel (E)
in corresponding holes. Screw cam
bolts (3) in corresponding pre-drilled
holes on underside of top panel (A).
Attach top panel (A) to panels (C, G,
D). Tighten cam locks (4).
Cover cam lock holes with paper
cover(22)
Page 5
11
4
44
20
fixed h o le
If the d raw er h its ad jo in ing
p arts,yo u can lo o sen th e
screw s o n m ale slid e an d
ad just th e h eig h t o f d raw er

Figure
Insert cam locks (4) into predrilled
holes on pre-assembled unit on
figure 5
Place dowels (1) of left/right side
panels (C, D) and center panel (E)
in corresponding holes. Screw cam
bolts (3) in corresponding pre-drilled
holes on bottom panel (B). Attach
bottom panel (B) to panels (C, G,
D). Tighten cam locks (4).
Cover cam lock holes with paper
cover(22)
Tip: It may be easier to place the
pre-assembled unit on its back to
complete this step.
Figure 7
Attach leg (P) and middle leg (Q) to
bottom panel (B) with bolt (2).
Tighten bolt with allen wrench (14).
Note: Front legs should flare out
towards the sides while rear legs
should flare out towards the back.
Secure top rail (G) to top panel (A)
with screws (21) using a phillips
screwdriver.
Figure 8
Attach back panel (H) with screws
(6) using a phillips screwdriver.
Page 6
P
P
P
P
21 21
21
6
H
6
66666
6
6
6
6
6
6
6
66
6
6
6
up
1
11
11
3
3
3
3
3
3
3
3
B
CE
D
1

Figure 9
Attach hinges (8) to door panel (O)
and left side panel (C) with screws
(5) using a phillips screwdriver.
Figure 10
Attach magnet (11) to center panel
(E) with screws (6).
Attach knob (9) to door panel (O)
with small bolt (10).
Tighten screws andbolts with
phillips screwdriver.
Page 7
5
5
8
8
scre w s fo r a d ju stin g
th e d o o r
to a ch ie ve u n ifo rm cle a ra n ce
a ro u n d th e d o o r,y o u m a y n e e d to a d ju st
th e d o o r b y tig h te n in g o r lo o se n in g th e
tw o scre w o n th e h in g e itse lf
611
10
9
6

Figure 11
Insert cam lock (4) into holes on
drawer bottom rail (S).
Screw cam bolts (3) into holes on
drawer back (M).
Attach drawer back (M) to drawer
bottom rail (S) by inserting cam
bolts (3) into corresponding holes
until drawer back (M) and drawer
bottom rail (S) meet.
Tighten by rotating cam locks (4)
clockwise with phillips screwdriver.
Attach the drawer side left (K) and
drawer side right (L) to drawer back
(M), match the grooves and tighten
them with screws (7).
Insert the drawer bottom (N) into the
corresponding groove of drawer
back (M), drawer side left (K) and
drawer side right (L).
Insert cam bolt (3) to drawer front
(I).
Attach drawer front (I) to drawer
bottom rail (S), drawer side left (K),
and drawer side right (L). Rotate
cam lock clockwise and insert
screws (7) into corresponding holes
in (K) and (L) to secure drawer front
(I).
Repeat steps using drawer front (J)
for the second drawer.
Figure
12
Attach male metal slide (20) to
drawer with screws (5).
Tighten screws with phillips
screwdriver.
Attach knob (9) to drawer front
with small bolt (10). Tighten
bolt with phillips screwdriver.
Make sure the open edge of the
rail is facing towards the back of
the drawer.
Page8
9
fixed h o le
If th e d raw er h its ad jo in in g
p arts,yo u can lo o sen th e
screw s o n m ale slid e an d
ad ju st th e h eig h t o f d raw er
I/J

Figure 13
Insert shelf pins (13) into holes
on left side panel (C) and
center panel (E). Slide shelf in.
Figure 14
Insert drawers by lining up
male and female components
of rails.
Make sure drawer’s male ball
bearings slide into side panels
female ball bearing slides.
Please try and make sure ball
bearings slide smoothly.
If the drawer hits adjoining
parts you can loosen the
screws on male slide and adjust
the height of drawer.
Figure 15
Attach b
racket
s
(1
5
) to back
panel using screws (19).
Tighten screws (19) using a
phillips screwdriver.
Mark two desired locations on
wall. Drill two 3/16" holes on
wall. Insert plastic anchors (17)
into the 2 holes on wall as
shown. (When doing this you
will need a hammer help you).
Then attach the bracket (15)
to wall using screw (18).
Tighten screws (18) using a
philips screwdriver.
Page 9
13 13
I
J
15
17
18
19