SEI HO664200TX User manual

HO664200TX – White
HO664300TX– Black
HO664400TX- Espresso
Corner Desk
Assembly Instructions
For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]
www.seidal.com
PO#11279
Page 1

HO664200TX–White / HO664300TX-Black / HO664400TX-Espresso
Corner Desk
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean,
padded surface like carpet or blanket. Check that you have all parts indicated. Call customer service if
hardware is missing. Before beginning assembly, carefully study the diagrams below and sort your
hardware according to the pictures. Using the incorrect hardware will cause damage.
A 1pc
Wood Top
B 1pc
Left Side Leg
C 1pc
Right Side Leg
D 2pcs
Bottom Stretcher
E 1pc
Left Long Shelf
F 1pc
Right Short Shelf
G 1pc
Drawer Right Panel
H 1pc
Drawer Left Panel
I 2pcs
Back Panel
J 1pc
Back Leg
K 1pc
Drawer Front Panel
L 1pc
Drawer Front Stretcher
M 1pc
Drawer Shelf
N 1pc
Drawer Back Panel
Page 2

Page 3
1 4pcs
Bolt Ø1/4”x 1-1/4”L
2 32pcs
Wood Dowel
3 10pcs
Screw Ø5/32”x1”L
4 23pcs
Cam Lock
5 23pcs
Cam Bolt
6 23pcs
Cover
7 2pcs
Hinge
8 12pcs
Screw Ø1/8”x1/2”L
9 1pc
Wood Knob
10 1pc
Bolt Ø5/32” x1”L
11 1pc
Plastic Cap
12 4pcs
Flat Washer
13 4pcs
Lock Washer
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096.
Assembly Tool Required
No.2 Phillips Screwdriver
(not included)

HO664200TX–White / HO664300TX-Black / HO664400TX-Espresso
Corner Desk
Assembly Instructions
Figure 1
Please do not over-tighten cam locks.
Please stop when you feel them
tighten.
Attach hinges (7) to drawer front panel
(K) and drawer front stretcher (L) by
using screws (8) as shown.
Figure 2
Insert cam locks (4) into holes on
drawer back panel (N) and drawer front
stretcher (L). Screw cam bolts (5) into
holes on drawer right panel (G). The
cam lock hole for drawer front stretcher
(L) should be facing down as shown on
the illustration. Make sure the holes for
the cam locks on drawer right panel (G)
and drawer back panel (N) are facing
upwards as shown.
Attach drawer left panel (H) to drawer
back panel (N) and drawer front
stretcher (L) by inserting wood dowels
(2) and cam bolts (5) into
corresponding holes until drawer right
panel (G), drawer back panel (N), and
drawer front stretcher (L) meet.
Tighten by rotating cam locks (4)
clockwise with Phillips screwdriver.
Make sure not to over tighten.
7
8
K
L
Page 4
Cam lock holes facing up

Figure 3
Repeat the same procedure as above
to attach drawer right side panel (G) to
drawer back panel (N) and drawer front
stretcher (L). Make sure the cam lock
holes are facing upwards.
Cover cam lock holes with covers (6).
Then attach wood knob (9) to drawer
front panel (K) by using screw (10).
Figure 4
Screw cam bolts (5) into corresponding
holes on the bottom of wood top (A).
A
Page 5

Figure 5
Insert cam locks (4) and wood dowels
(2) into corresponding holes on
assembled unit from figure 3.
Figure 6
Attach assembled unit from figure 5 to
wood top (A) by inserting wood dowels
(2) and cam bolts (5) into
corresponding holes until assembled
unit from figure 5 and wood top (A)
meet.
Tighten by rotating cam locks (4)
clockwise with Phillips screwdriver.
Cover cam lock holes with covers (6).
You might find it easier to insert the
wood dowels (2) into the corresponding
holes on wood top (A) before attaching
the assembled unit from figure 5.
A
Page 6

Figure 7
Insert screws (3) into bottom stretcher
(D).Attach bottom stretcher (D) to left
long shelf (E) by inserting screws (3)
into predrilled holes on left long shelf
(E).
Tighten screws (3) with Phillips
screwdriver.
Make sure to insert the screws through
the big hole on bottom stretcher (D)
rather than the small hole.
Figure 8
Insert cam locks (4) into corresponding
holes on back panel (I) and assembled
unit from figure 7. Screw cam bolts (5)
into holes on left side leg (B).
Attach back panel (I) and assembled
unit from figure 7 to left side leg (B) by
inserting wood dowels (2) and cam
bolts (5) into corresponding holes until
assembled unit from figure 4 and back
panel (I) and left side leg (B) meet.
Make sure back panel (9) has the cam
lock holes facing upward.
Tighten by rotating cam locks (4)
clockwise with Phillips screwdriver.
Cover cam lock holes with covers (6).
E
D
3
2
Page 7
Cam lock holes
facing up

Figure 9
Insert cam locks (4) into holes on
assembled unit from figure 8. Screw
cam bolts (5) into holes on back leg (J).
Attach back leg (J) to assembled unit
from figure 8 by inserting wood dowels
(2) and cam bolts (5) into
corresponding holes until assembled
unit from figure 8 and back leg (J)
meet.
Tighten by rotating cam locks (4)
clockwise with Phillips screwdriver.
Cover cam lock holes with covers (6).
Make sure the additional cam lock and
wood dowel holes are facing outwards
as shown in the illustration.
Figure 10
Insert screws (3) through bottom
stretcher (D) and into the predrilled
holes on right short shelf (F).
Tighten screws (3) with Phillips
screwdriver.
2
Page 8
Holes
facing out

Figure 11
Insert cam locks (4) into holes on back
panel (I) and assembled unit from
figure 10. Screw cam bolts (5) into
holes on right side leg (C).
Attach back panel (I) and assembled
unit from figure 10 to right side leg (C)
by inserting wood dowels (2) and cam
bolts (5) into corresponding holes until
assembled unit from figure 7 and back
panel (I) and right side leg (C) meet.
Tighten by rotating cam locks (4)
clockwise with Phillips screwdriver.
Cover cam lock holes with covers (6).
Make sure the cam lock holes on back
panel (I) are facing upwards as shown.
Figure 12
Insert cam locks (4) into holes on
assembled unit from figure 11. Screw
cam bolts (5) into holes on assembled
unit from figure 9.
Attach assembled unit from figure 11 to
assembled unit from figure 9 by
inserting wood dowels (2) and cam
bolts (5) into corresponding holes until
assembled unit from figure 11 and
assembled unit from figure 9 meet.
Tighten by rotating cam locks (4)
clockwise with Phillips screwdriver.
Cover cam lock holes with covers (6).
This step may be easier with the help
of another person.
Page 9
Cam lock holes
fa
cing up

Figure 13
Insert cam locks (4) into holes on
assembled unit from figure 12. Screw
cam bolts (5) into holes on the bottom
of wood top (A).
Attach wood top (A) to assembled unit
from figure 12 by inserting wood
dowels (2) and cam bolts (5) into
corresponding holes until assembled
unit from figure 12 and wood top (A)
meet.
Insert bolts (1) through lock washers
(13) and flat washers (12) to connect
assembled unit from figure 12 and
wood top together.
Tighten by rotating cam locks (4) and
bolts (1) clockwise with Phillips
screwdriver.
Cover cam lock holes with covers (6).
This step is easier with the help of
another person.
Figure 14
Turn the table upside down.
Insert screws (3) into holes on
assembled unit from figure 13 as
shown.
Tighten screws (3) with Phillips
screwdriver.
Page 10

Figure 15
Turn the table over and slide drawer
shelf (M) into the slides of unit as
shown.
Figure 16
Insert plastic cap (11) into the hole on
the wood top (A) as shown.
Now your new corner desk is ready to
use!
Page 11

Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri
Central time if you have product issues or email us at [e-mail]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
Page 12