SEI Dunston HZ103900TX User manual

Page |
1
PO#:
HZ103900TX
Dunston Bar Cabinet
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service: 1-800-633-5096
[email protected]om
www.seidal.com

Page |
2
1) Quantity
of 1
Top Panel
2) Quantity
of 1
Left Side Panel
3) Quantity
of 1
Right Side Panel
4) Quantity
of 1
Bottom Panel
5) Quantity
of 1
Upper Back Panel
6) Quantity
of 1
Lower Shelf Panel
7) Quantity
of 2
Middle Panels
8) Quantity
of 2
Shelf Panels
9) Quantity
of 8
Article Wine Racks
10) Quantity
of 2
Side Small Middle Panels
11) Quantity
of 3
Small Middle Panels
12) Quantity
of 1
Lower Back Panel
13) Quantity
of 1
Drawer Crossbar
14) Quantity
of 1
Back Connector Panel
15) Quantity
of 1
Lower Bottom Panel
Dunston Bar Cabinet
Parts List
Please review all parts and hardware before disposing of any packaging.
Before beginning assembly, separate each type of hardware. Carefully study the diagrams below and check
that you have all parts indicated. Call Customer Service if missing hardware. Using the incorrect hardware
will cause damage.

Page |
3
16) Quantity
of 1
Left Side Frame
17) Quantity
of 1
Right Side Frame
18) Quantity
of 1
Drawer Face Panel
19) Quantity
of 1
Left Drawer Side Panel
20) Quantity
of 1
Right Drawer Side Panel
21) Quantity
of 1
Drawer Back Panel
22) Quantity
of 1
Drawer Brace Panel
23) Quantity
of 1
Drawer Bottom Panel
24) Quantity
of 1
Left Door
25) Quantity
of 1
Right Door
26) Quantity
of 1
Glass Shelf

Page |
4
A) Quantity
of 37
Cam Bolts
B) Quantity
of 37
Cam Locks
C) Quantity
of 22
Cotton Mats
D) Quantity
of 9
Small Cam Bolts
E) Quantity
of 9
Small Cam Locks
F) Quantity
of 50
Wood Dowels Dia. 5/16” x1-1/4”L
G) Quantity
of 2
Door Handles
H) Quantity
of 1
Drawer Handle
I) Quantity
of 2
Bolts Dia. 5/32’’ x 1/2"L
J) Quantity
of 1
Bolt Dia. 5/32’’ x 1"L
K) Quantity
of 25
Screws Dia. 5/32” x 1"L
L) Quantity
of 14
Screws Dia. 1/8” x 1/2”L
M) Quantity
of 8
Bolts Dia. 1/4x1-1/4” L
N) Quantity
of 8
Flat Washers Dia. 1/4”x3/4”
O) Quantity
of 8
Spring Washers Dia. 1/4”
P) Quantity
of 1
Magnet
Q) Quantity
of 2
Magnet Plates
R) Quantity
of 2
Screws
Dia. 1/8” x 1/2”L

Page |
5
S) Quantity
of 4
Hinges
T) Quantity
of 24
Screws Dia. 1/8” x 5/8”L
U) Quantity
of 4
Shelf Pins
V) Quantity
of 1
Allen Wrench
W) Quantity
of 2
Tilt Prevent Hardware
X) Quantity
of 1
Cam Tool
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the
finish. Avoid rubbing or scratching the surface
with rough or abrasive objects.
For replacement parts or questions, please call
Customer Service at 1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver
(Not Included)

Page |
6
Figure 1
Start screwing with fingers to help align
screw.
Use Screws (K) and Wood Dowels (F) to
attach Article Wine Racks (9) to Top Panel
(1) and both Shelf Panels (8).
Tighten screws with Phillips screwdriver.
Figure 2
Start screwing with finger to help align
cam bolts.
Insert Cam Locks (B) into holes on Middle
Panels (7).
Screw Cam Bolts (A) into threaded holes on
Lower Shelf Panel (6).
Attach Lower Shelf Panel (6) to Middle
Panels (7) using Cam Bolts (A) and Wood
Dowels (F).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver.
Cover Cam Locks (B) with Cotton Mats (C)
provided.
Note: Make sure holes for adjustable shelf
on Middle Panels (7) are facing in towards
each other.
Dunston Bar Cabinet
Assembly Instructions

Page |
7
Figure 3
Insert Cam Locks (B) into holes on Upper
Back Panel (5).
Screw Cam Bolts (A) into threaded holes on
Lower Shelf Panel (6).
Attach Upper Back Panel (5) to Lower Shelf
Panel (6) using Cam Bolts (A).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver.
Attach Shelf Panels (8) to Middle Panels (7)
by inserting Wood Dowels (F) into
corresponding holes.
Figure 4
Insert Cam Locks (B) into holes on Upper
Back Panel (5) and Shelf Panel (6).
Screw Cam Bolts (A) into threaded holes on
Left Side Panel (2) and Right Side Panel (3).
Attach Left Side Panel (2) and Right Side
Panel (3) to assembled unit from Figure 3
using Cam Bolts (A) and Wood Dowel (F).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver or Cam Tool (X).
7
7

Page |
8
Figure 5
Start with finger to help align Cam Bolts.
Insert Small Cam Locks (E) into pre-drilled
holes on Side Small Middle Panel (10).
Screw Small Cam Bolts (D) into pre-drilled
holes on Lower Shelf Panel (6).
Attach assembled unit & Side Small Middle
Panel (10) & Small Middle Panel (11) by
inserting Small Cam Bolts (D) into
corresponding holes until all components
meet.
Tighten Small Cam Bolts (D) by rotating
Small Cam Locks (E) clockwise using
Phillips screwdriver (not included).
Cover Small Cam Locks (E) with Cotton
Mat (C) provided.
Figure 6
Start with finger to help align Cam Bolts.
Insert Cam Locks (B/E) into pre-drilled
holes on pre-assembled unit from figure 5
Screw Cam Bolts (A/D) and Wood Bowel
(F) into pre-drilled holes on Bottom Panel
(4).
Attach pre-assembled unit from figure 5&
Bottom Panel (4) by inserting Cam Bolts
(A/D) and Wood Dowel (F) into
corresponding holes until all components
meet.
Tighten Cam Bolts (A/D) by rotating Cam
Locks (B/E) clockwise using Phillips
screwdriver (not included).
Cover Cam Locks (B/E) with Cotton Mat
(C) provided.
C
6

Page |
9
Figure 7
Insert Cam Locks (B) into holes on
assembled unit from Figure 5.
Screw Cam Bolts (A) into threaded holes on
Top Panel (1).
Attach Top Panel (1) to assembled unit using
Cam Bolts (A) and Wood Dowels (F).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver or Cam Tool (X).
Cover Cam Locks (B) with Cotton Mat (C).
Figure 8
Use Screws (L) to attach Lower Back Panel
(12) to unit.
Tighten Screws (L) with Phillips screwdriver.

Page |
10
Figure 9
Insert Cam Locks (B) into holes on Drawer
Crossbar (13).
Screw Cam Bolts (A) into threaded holes on
Left Side Panel (2) and Right Side Panel (3).
Attach Left Side Panel (2) and Right Side
Panel (3) to Drawer Crossbar (13) using Cam
Bolts (A) and Wood Dowels (F).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver.
Attach Back Connector Panel (14) and Lower
Bottom Panel (15) to Side Panels (2/3) using
Bolts (M), Flat Washers (N), and Spring
Washers (O).
Tighten Bolts (M) with Allen Wrench (V).
Figure 10
Insert Cam Locks (B) into holes on Left Side
Frame (16), Right Side Frame (17), and Back
Connector Panel (14).
Screw Cam Bolts (A) into predrilled holes on
Bottom Panel (4).
Attach pre-assembled unit from figure 8 to
pre-assembled unit from figure 9 using Cam
Bolts (A) and Wood Dowels (F).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver.

Page |
11
Figure 11
Attach Left Door (24) and Right Door (25)
onto assembled unit using Hinges (S) and
Screws (T).
Attach Magnet (P) to assembled unit using
Screw (L).
Attach Magnet Plate (Q) to inside of door
panels using Screws (R).
Tighten Screws (T) with a Phillips
screwdriver.
Attach Door Handles (G) to doors using Bolt
(I).
Tighten bolts with Phillips screwdriver.
Figure 12
Insert Shelf Pins (U) into holes on side
panels.
Insert adjustable Glass Shelf (26) in arrows
direction. Make sure Shelf Pins (U) stably
holds glass shelf.
If Console is not level, please adjust leg’s
adjustable foot pad by hand.

Page |
12
Figure 13
Insert Cam Lock (E) into hole on Drawer
Brace Panel (22).
Screw Cam Bolt (D) into threaded hole on
Drawer Face Panel (18) and attach to Drawer
Brace Panel (22).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver.
Attach Drawer Side Panels (19/20) to Drawer
Back Panel (21) using Screws (K). Tighten
with Phillips screwdriver.
Insert Drawer Bottom Panel (23) into grooves
of Panels (19/20/21).
Attach Drawer Front Panel (18) to unit using
Screws (K).
Attach Knob (H) to Drawer Front Panel (18)
using Bolts (J). Tighten with Phillips
screwdriver.
Figure 14
Insert drawer into assembled unit.
Make sure all slides glide smoothly in and
out.
Note: There is a lever located on male
slide for bottom drawer slide. Push lever
to either side in order to detach male slide
from female slide.

Page |
13
Figure 15
Attach Brackets (W) to Back Panel using
Screws (W). Tighten Screws (W) using a
Philips screwdriver.
Mark two desired locations on wall, same
distance as Brackets (W) on back of unit. Drill
two 3/16" holes on wall. Insert Plastic
Anchors (W) into holes on wall. (Use hammer
to help.)
Attach Brackets (W) to wall using Screws
(W). Tighten using a Philips screwdriver.
Move this item close to wall Brackets (W) and
tie in both Brackets (W) with Plastic Straps
(W) as shown.
Anti-tipping hardware must be used
for this product to avoid tipping and
injury.
Figure 16
Now your Dunston Bar Cabinet is ready to
use!
W

Page |
14
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time frame.
Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s) and we are not
responsible for any damages due to product modification(s). If damages or missing parts are not reported within 90 days
of your receipt, we are under no obligation to provide parts or replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas), Mon-Fri
9am – 4pm CST, or email us at [e-mail]. Please ask for customer service representative for issues
involving damages or replacement parts. Please ask for technical assistance representative for any issues with product
and assembly/construction.
Please contact the retailer that you purchased from for returns.
Parts Replacement Form
Customer Service: 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019