SEI Kismet Multi-Finish Cabinet HZ030300TX User manual

Page |
1
PO#:
HZ030300TX
Kismet Multi-Finish Cabinet
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises, Inc.
Customer Service: 1-800-633-5096
[email protected]om
www.seifurniturestore
.com

Page |
2
1) Quantity
of 1
Top Panel
2) Quantity
of 4
Left Side Panel
3) Quantity
of 4
Right Side Panel
4) Quantity
of 1
Bottom Panel
5) Quantity
of 2
Upper Shelf Panel
6)Quantity
of 1
Lower Shelf Panel
7) Quantity
of 2
Drawer Front Panel-1
8) Quantity
of 1
Drawer Front Panel-2
9) Quantity
of 1
Drawer Front Panel-3
10) Quantity
of 4
Drawer Left Side Panel
11) Quantity
of 4
Drawer Right Side Panel
12) Quantity
of 4
Drawer Back Panel
Kismet Multifinish Cabinet
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or a blanket. Check that you have all parts indicated. Call customer service if any hardware is
missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according to the
pictures. Using the incorrect hardware will cause damage.
.

Page |
3
13) Quantity
of 4
Drawer Bottom Panel
14) Quantity
of 4
Back Panel
15 ) Quantity
of 2
Metal Frame
16) Quantity
of 2
Top Stretcher
17) Quantity
of 2
Bottom Stretcher
A) Quantity
of 32
Cam Bolts
B) Quantity
of 32
Cam Locks
C) Quantity
of 32
Wood Dowels Dia. 5/16"x1-1/4"
D)Quantity
o f 16
Bolt Dia. 1/4x3/4” L
E)Quantity
o f 16
Spring Washer Dia.1/4”
F)Quantity
o f 16
Flat washer Dia.1/4” x3/4”
G) Quantity
of 1
Allen Wrench
H
) Quantity
of 58
Screw Dia. 1/8” x 1/2”L
I) Quantity
of 8
Knob

Page |
4
J) Quantity
of 16
Bolts
Dia. 5/32”x 1”L
K) Quantity
of 32
Screw
Dia. 5/32”x 1L
L) Quantity
of 2
Plastic Strap
M) Quantity
of 4
Bracket
N) Quantity
of 2
Screws Dia. 1/8”x1-1/2”L
O) Quantity
of 2
Screws Dia. 1/8”x5/8”L
P) Quantity
of 2
Anchor
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Avoid rubbing or scratching the surface with
rough or abrasive objects.
For replacement parts or questions, please call
SEI Customer Service at 1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver, Hammer
(Not Included)

Page |
5
Figure 1
Align Bolts (D) by hand.
Attach the Metal Frames (15) to
Top Stretchers (16) and Bottom
Stretchers (17) with Bolts (D),
Spring Washers (E), and Flat
Washers (F).
Tighten Bolts (D) with Allen
Wrench (G).
Figure 2
Attach the assembled unit from
Figure1 to the Bottom Panel (4)
with Screws (H).
Tighten Screws (H) with Phillips
screwdriver (not included).
Kismet Multifinish Cabinet
Assembly Instructions
D
15
15

Page |
6
Please do not overtighten cam locks. Stop when they feel secure.
Figure 3
Align Cam Bolts (A) by hand .
Insert Cam Locks (B) into
corresponding holes on Side
Panels (2/3).
Screw Cam Bolts (A) into threaded
holes on Bottom Panel (4).
Attach Side Panels (2/3) to Bottom
Panel (4) by inserting Cam Bolts
(A) and Wood Dowels (C) into
corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Figure 4
Align Cam Bolts (A) by hand.
Insert Cam Locks (B) into
corresponding holes on Side
Panels (2/3).
Screw Cam Bolts (A) into threaded
holes on Lower Shelf Panel (6).
Attach Lower Shelf Panel (6) to
Side Panels (2/3) by inserting Cam
Bolts (A) and Wood Dowels (C)
into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
2
3
A
C
C
A

Page |
7
Figure 5
Align Cam Bolts (A) by hand.
Insert Cam Locks (B) into
corresponding holes on Side
Panels (2/3).
Screw Cam Bolts (A) into threaded
holes on Lower Shelf Panel (6).
Attach Side Panels (2/3) to Lower
Shelf Panel (6) by inserting Cam
Bolts (A) and Wood Dowels (C)
into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Figure 6
Align Cam Bolts (A) by hand.
Insert Cam Locks (B) into
corresponding holes on Side
Panels (2/3).
Screw Cam Bolts (A) into threaded
holes on Upper Shelf Panel (5).
Attach Upper Shelf Panel (5) to
Side Panels (2/3) by inserting Cam
Bolts (A) and Wood Dowels (C)
into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
A
A

Page |
8
Figure 7
Align Cam Bolts (A) by hand.
Insert Cam Locks (B) into
corresponding holes on Side
Panels (2/3).
Screw Cam Bolts (A) into threaded
holes on Upper Shelf Panel (5).
Attach Side Panels (2/3) to Upper
Shelf Panel (5) by inserting Cam
Bolts (A) and Wood Dowels (C)
into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not include).
Figure 8
Align Cam Bolts (A) by hand.
Insert Cam Locks (B) into
corresponding holes on Side
Panels (2/3).
Screw Cam Bolts (A) into threaded
holes on Shelf Panel (5).
Attach Shelf Panel (5) to Side
Panels (2/3) by inserting Cam
Bolts (A) and Wood Dowels (C)
into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
A
C
A
C

Page |
9
Figure 9
Align Cam Bolts (A) by hand.
Insert Cam Locks (B) into
corresponding holes on Side
Panels (2/3).
Screw Cam Bolts (A) into threaded
holes on Shelf Panel (5).
Attach Side Panels (2/3) to Shelf
Panel (5) by inserting Cam Bolts
(A) and Wood Dowels (C) into
corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Figure 10
Align Cam Bolts (A) by hand.
Insert Cam Locks (B) into
corresponding holes on Side
Panels (2/3).
Screw Cam Bolts (A) into threaded
holes on Top Panel (1).
Attach Top Panel (1) to Side
Panels (2/3) by inserting Cam
Bolts (A) and Wood Dowels (C)
into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
C

Page |
10
Figure 11
Attach Back Panels (14) to back of
the unit with Screws (H).
Tighten Screws (H) with Phillips
screwdriver (not included) .
Figure 12
Align Screws (K) by hand.
Attach Drawer Side Panels (10/11)
to Drawer Back Panels (12) using
Screws (K).
Tighten Screws (K) with Phillips
screwdriver (not included).
Insert Drawer Bottom Panels (13)
into the grooves of Drawer Side
Panels (10/11/12).
Attach Drawer Front Panels
(7/8/9) to the assembled units
using Screws (K).
Finally, attach Knobs (I) to the
Drawer Front Panels (7/8/9) using
Bolts (I).
Tighten Bolts (I) with Phillips
screwdriver (not included).
Repeat step for additional drawers
using Drawer Front Panels (7/8/9).
K
J
I
J
J