SEI NANTUCKET DN1439 User manual

STYLE NO. DN1439
JCP LOT#781-3510
SOUTHERN ENTERPRISES INC.
RELAX...If you can follow a few easy, step-by-step directions
in order .YOU CAN ASSEMBLE THIS ITEM.
3BREAKFAST SE -PC NANTUCKET
T
PLEASE FIND HARDWARE IN RED POLYBAG BEFORE DISCARDING PACKING MATERIAL.
HARDWARE LIST
(1) MEDIUM MACHINE SCREW
(Ø5/16”X1-1/2”)
8PCS
(6) WOOD SCREW
11PCS
(2) SHORT MACHINE SCREW
(Ø5/16”X1”)
14PCS
(7) T-BOLT 18PCS
(3) LONG MACHINE SCREW
(Ø5/16”X2-1/2”)
18PCS
(8) WOOD DOWEL
48PCS
(4) WRENCH
1PC
(9) WOOD PLUG
24PCS
(5) METAL HANDLE
1PC
(10) DRAWER STOPPER
1PC
PARTS LIST
(A) TOP 1PC
(K) DRAWER BACK
1PC
(B) LEFT SIDE PANEL
1PC
(L) DRAWER LEFT SIDE
1PC
(C) RIGHT SIDE PANEL
1PC
(M) DRAWER RIGHT SIDE 1PC
(D) BACK PANEL
1PC
(N) DRAWER BOTTOM 1PC

(E) FRONT PANEL
1PC
(O) SIDE FRAME
4PCS
(F) SHELF 1PC
(P) UPPER CROSS BRACE
4PCS
(G) RIGHT HOLDER
1PC
(Q) MIDDLE CROSS BRACE
4PCS
(H) LEFT HOLDER
1PC
(R) LOWER CROSS BRACE
4PCS
(I) WOOD BAR 1PC
(S) SEAT PANEL
2PCS
(J) DRAWER FRONT 1PC
ASSEMBLY INSTRUCTIONS
1. SELECTASMOOTH, SOFT SURFACE TO PREVENT SCRATCHING FINISH.
2. YOU MAY NEED A PHILLIP SCREWDRIVER.
3. INSERT WOOD DOWELS (8) INTO PREDRILLED HOLES ON ENDS OF SHELF (F), FRONTAND BACK
PANELS (E, D) AND FIT INTO CORRESPONDING HOLES ON INSIDE OF LEFT AND RIGHT SIDE
PANELS (B, C). INSERT SHORT MACHINE SCREWS (2) THROUGH PREDRILLED HOLES ON WOOD
BARS ON PARTS (D, E, F) AND TIGHTEN INTO PRETHREADED HOLES ON LEFT AND RIGHT SIDE
PANELS (B, C) BY USING WRENCH (4). (AS SHOWN IN FIGURE 1)
4. INSERT WOOD DOWELS (8) INTO PREDRILLED HOLES ON UNDERSIDE OF TOP (A) AND FIT INTO
CORRESPONDING HOLES ON EDGES OF FRONT AND BACK PANELS (E, D). INSERT SHORT
MACHINE SCREWS (2) THROUGH PREDRILLED HOLES ON WOOD BARS ON PARTS (B, C, D, E) AND
TIGHTEN INTO PRETHREADED HOLES ON UNDERSIDE OF TOP (A) BY USING WRENCH (4). (AS
SHOWN IN FIGURE 2)
5. FIT WOOD BAR (I) INTO THE HOLES ON LEFT AND RIGHT HOLDERS (G, H). INSERT WOOD
DOWELS (8) INTO PREDRILLED HOLES ON LEFTAND RIGHT HOLDERS (G, H) AND FIT INTO
CORRESPONDING HOLES ON OUTSIDE OF RIGHT SIDE PANEL (C). INSERT T-BOLTS (7) INTO THE
HOLES ON LEFT AND RIGHT HOLDERS (G, H), AND TIGHTEN LONG MACHINE SCREWS (3)

THROUGH PREDRILLED HOLES ON RIGHT SIDE PANEL (C) INTO T-BOLTS (7) BY USING WRENCH
(4). PLEASE NOTE THAT IF SCREWS DO NOT TIGHTEN, ROTATE T-BOLTS (7) SO THAT THREAD OF
T-BOLTS ARE FACING SCREWS. (AS SHOWN IN FIGURE 2)
FIGURE1 FIGURE2
6. INSERT WOOD SCREWS (6) THROUGH PREDRILLED HOLES ON OUTSIDE OF DRAWER LEFT SIDE
(L) AND TIGHTEN INTO CORRESPONDING HOLES ON ENDS OF DRAWER FRONT AND BACK (J, K).
SLIDE DRAWER BOTTOM (N) INTO GROOVES ON INSIDE OF DRAWER FRONTAND BACK (J, K)
AND ALIGN WITH THE GROOVE ON DRAWER LEFT SIDE (L). REPEAT SAME PROCEDURE FOR
DRAWER RIGHT SIDE (M). INSERT WOOD SCREWS (6) THROUGH METAL HANDLE (5) AND
TIGHTEN INTO PREDRILLED HOLES ON DRAWER FRONT (J). INSERT WOOD SCREW (6) THROUGH
DRAWER STOPPER (10) AND TIGHTEN INTO PREDRILLED HOLE ON FRONT PANEL (E). THEN
PLACE THEASSEMBLED DRAWER INTO SPACE OF BAR TABLE. (AS SHOWN IN FIGURES 3 & 4).
FIGURE3 FIGURE4

7. INSERT WOOD DOWELS (8) INTO PREDRILLED HOLES ON ENDS OF PARTS (P, Q, R) AND FIT INTO
CORRESPONDING HOLES ON SIDE FRAMES (O), FIT T-BOLTS (7) INTO THE HOLES ON PARTS (P, R).
AND TIGHTEN LONG MACHINE SCREWS (3) THROUGH PREDRILLED HOLES ON SIDE FRAMES (O)
INTO T-BOLTS (7) BY USING WRENCH (4). PUSH WOOD PLUGS (9) INTO THE HOLES ON OUTSIDE
OF SIDE FRAMES (O). PLEASE NOTE THAT IF SCREWS DO NOT TIGHTEN, ROTATE T-BOLTS (7) SO
THAT THREAD OF T-BOLTS ARE FACING SCREWS. (AS SHOWN IN FIGURE 5)
8. INSERT MEDIUM MACHINE SCREWS (1) THROUGH PREDRILLED HOLES ON SIDE FRAMES (O)
AND TIGHTEN INTO PRETHREADED HOLES ON UNDERSIDE OF SEAT PANEL (S). (AS SHOWN IN
FIGURE 6)
FIGURE5 FIGURE6
READY
YOUR NEW 3-PC NANTUCKET BREAKFAST SET IS FINISHED AND READY TO USE.

Please count, identify and compare parts and hardware list to be sure all parts are present. It may help to
divide parts and label them to correspond with part list. Extra hardware may be included. If any items are
missing, please contact our parts/service department at [phone] or in Dallas [phone]/ 9am –
4pm Mon-Fri Central time. Missing or damaged hardware and/ or parts will be replaced free of charge. WE
DO NOT SELL PARTS. WE DO NOT RECOMMEND MODIFYING PRODUCT(S) AND WE ARE NOT
RESPONSIBLE FOR ANY DAMAGES DUE TO PRODUCT MODIFICATION(S). If this product has not
been purchased from our retail affiliates (within 9 months), we are under no obligation to provide parts or
replacement merchandise. Parts will not be available for items arriving fully assembled.
"We will ship parts if available" "This is not a warranty"
PARTS REPLACEMENT FORM
STYLE NO:DN1439
JCP LOT#781-3510
Customer Name PARTS
LETTER PART DESCRIPTION QUANTITY NEEDED
Street, City, State, Zip
Phone#
Please indicate where you purchased this item.
Store/website/catalog
/ /
Please indicate color/size/style number
SOUTHERN ENTERPRISES INC.
P.O. Box 59996 Dallas, Texas 75229
/ /