Seiwa LCHA Series User manual

‐1‐
Instruction Manual
Vapor Tight Type LED Lighting Fittings for High Temparature
LCHA
Thank you very much for purchasing our LED lighting fittings.
Please read this instruction manual to use the product properly.
IP rating: IP65
Rated input voltage: 100ー242 VAC (50/60 Hz).
To be conserved
After installing the product, be sure to hand this manual over to the user of the product.
Performance
Pi
p
e Pendant T
yp
e, Bracket T
yp
e
Firmly mount the terminal box and suspension fitting to the
structure (e.g. ceiling).
Connect the suspension pipes A and B to the Pipe Holder of
fitting.
Insert the suspension pipe A into the tightening ring. Make
sure that the O‐ring is in place in the groove on the terminal
box cover. Then screw the pipe into the terminal box cover.
Lift up the fitting and connect it to the suspension fitting, and
then connect the suspension hook to the terminal box.
Connect the power and grounding wires inside the
terminal box and conduct insulation treatment on them.
Then, remove the suspension hook and place the hook in
the terminal box cover.
Fit the terminal box cover into the terminal box and turn
the fastening ring 90 degrees until the projection aligns
with the red mark.
Tighten the locking screws.
Tighten the fixing nuts on the suspension bracket.
Suspension Pipe A
End with a rubber plug
Suspension Pipe B
How to Install the Fitting
11E0000823C11

‐2‐
CAUTIONS
1. Confirm that the screws and bolts are fastened properly and tightly.
2. For outdoor use, waterproof the screwed portion of the conduit, the cable entry fittings and the joints with the stand pole to prevent
rainwater infiltration.
3. In the case of the stanchion type, be sure to provide a support at least 1500 mm above the bottom of the pole.
4. When installing the fitting, be sure to connect external wires inside a specified part of the fitting.
Don’t use any other part for wire connection.
5. Don’t open the front glass. The LED internal parts may be very hot. Don’t touch the LED light sources.
Otherwise a malfunction or lighting failure might occur.
6. The ambient temperature should be within the range of ‐20 to +60℃.
NB: Even when the ambient temperature is 60°C, the product should not be used in an environment in which there is a heat source
(heater, etc.) nearby and it may be exposed to direct heat.
7. The supply voltage variation should be within ±6% of the rating.
8. Plug the entries of the terminal box which are not used.
9. Confirm that the fitting is adequately grounded.
10. Prior to maintenance or inspection, be sure to turn off the power.
11. To prevent shortening of the service life, avoid turning on the fitting in direct sunlight.
12. To avoid noise or malfunctioning, don't use a radio, television or wireless infrared remote control near the fitting.
13. In the case of white LEDs, luminescent color and brightness may vary with individual LEDs.
Also note that they differ in terms of attenuation over time.
14. The LED light sources and the power supply unit cannot be replaced.
15. For use in an unfavorable location (a place in which there is strong wind, vibration or the possibility of salt damage or in a dusty or
corrosive gas atmosphere), a special countermeasure should be taken.
16. The product should not be used in an environment in which the temperature and humidity are always high, such as a bathroom for
business or sauna.
Pass the lead from the fitting through the stand pole and insert the pole into the pole
connection box in the arrow direction.
Fix the clamp with the pan‐head screw.
Tighten the locking screw on the pole connection box.
Be sure to waterproof the commercial terminal box (not supplied) and short nipple (not
supplied) and the screw on the lower part of the pole with a sealing agent.
Fix the stand pole with a pole support (not supplied) and the mounting hole of a
terminal box (not supplied) securely.
Connect the power and grounding wires inside the terminal box (not supplied) and
conduct insulation treatment on them.
Pass the lead from the lighting fitting through the flexible fitting
and attach the flexible fitting to the fitting.
Attach the other end of the flexible fitting to the terminal box.
Fix the fitting and the terminal box on the mounting surfaces
securely.
Connect the power and grounding wires inside the terminal box
(not supplied) and conduct insulation treatment on them.
Stanchion T
yp
e
Pan‐Head Screw
Clamp
Screw G3/4
Pole Connection Box
Support, Not supplied
Locking Bolts
Stand Pole
Short Nipple G3/4.,Not supplied
Clamp Holder
Terminal Box, Not supplied
Special Direct Mount Type
Terminal Box
Holes Holes
Interval 500
Flexible Fitting
(Increased Safety)

- Prior to use, please read the safety precautions and instruction manual thoroughly to use the product properly.
-
- Please keep the manual in a handy place for later reference.
●The various marks have the following meanings:
Before cleaning, be sure to turn off the power.
Otherwise, a fire or electric shock might result.
Do’t ed, tist or pull the poer ale y fore.
Inadequate handling of the cable might damage it and result in a fire or electric shock.
The parts once removed for cleaning should be replaced properly according to the instruction manual.
An improperly placed part might cause the product to fall, resultng in an injury or property damage.
Do’t ope LED lap protetie oers suh as the frot glass ad glass gloe.
Do’t touh a LED lap, otherise a alfutio or lightig failure ight our.
In grounding work, be sure to follow the technical standards for electrical equipmentof your country. Inadequate grounding
might cause a fire or electric shock.
When leading the power cable into the product through a conduit or the like, waterproof the connection and joint
adequately to prevent water infiltration. Inadequate waterproofing might cause a fire or electric shock.
Do’t oer the produt ith a iflaale aterial suh as loth or paper or put aythig i the produt.
Such a material or thing might cause a fire.
11E0001048C11
Don’t use the product in a hazardous location where a flammable or explosive atmosphere such as a gaseous, steamy or
dusty atmosphere may exist. Use in such a location might cause an explosion or fire.
The ambient temperature should be within the operating temperature range specified in the instruction manual. If the
product should be used at a temperature higher than specified, an early lighting failure or malfunction might occur or a fire
might result.
If a product must be oriented in a specific manner for use, install it properly according to the marking on its body or the
instruction manual. Otherwise, a fire or electric shock might result.
Don’t touch.
Disassembly &
conversion
prohibited.
Don’t use near
a water source.
Be sure to turn
off the power.
Safety Precautions
To be conserved
After installing the product, be sure to hand the safety precautions and instruction manual over to the user of the product.
Caution
WARNING:
CAUTION:
Improper handling may lead to a human death or serious bodily injury.
Improper handling may lead to a bodily injury or property damage.
WARNING
Be sure to
follow the
instructions.
Be sure to
ground.
Prohibited.
L高照般4
Do’t oert the produt.
Conversion might cause the product to fall or result in a fire or electric shock.
For electrical connections, use crimp-type terminals, etc. to secure the connections and conduct insulation treatment. An
inadequate connection or inadequate insulation might cause an imperfect contact, leading to a fire or electric shock.
Be careful of
ignition.
- 1 /2 -

Please note that the above addresses and phone numbers may be changed.
Installation of the product should be carried out by a qualified person.
Installation by an unqualified person is legally prohibited.
CAUTION
For further information on the product, contact any of our offices listed below (if you like to make an inquiry, let us know the model name
indicated on the product nameplate).
CONTACT DETAILS
Fax
The product should be mounted on a surface robust enough to support its weight, properly according to the instruction
manual. Improper installation might cause the product to fall or result in an electric shock or injury.
If you continue to use the product in an abnormal condition (smoke, odor, etc.), a fire or electric shock might result. If you
detect an abnormality, immediately turn off the power switch. Confirm that the abnormal condition has been eliminated
and make a repair call.
Don’t use the product in a strong corrosive gas atmosphere which contains hydrochloric acid or chlorine gases or the like.
Use in a corrosive gas atmosphere might cause the product to corrode and fall, resulting in an injury.
SEIWA ELECTRIC MFG.CO., LTD.
Do’t use the produt at a oltage other tha the rated oltage idiated o the aeplate.
Otherwise, breakage, fire or electric shock might result.
Any product not marked as a product for outdoor use should not be used outdoors or in a humid place or near a water
source. Its use in such a place might cause a fire or electric shock.
WARNING
+81 3 5833 8946
A lighting fitting has a service life. A product which has been used for eight to ten years may have degraded internal parts
even if it looks normal. For safety and energy saving, we recommend you check and replace it. The LED module design life is
40,000 hours (different from the lighting fitting life) when used at an ambient temperature of 60°C, 10 hours per day, 3,000
hours per year. If used at a higher temperature or more hours per year, the life would be shortened. Have a specialist
inspect the product every three years. If used for an extended period without inspection, a smoke, fire, or electric shock
might result.
Tokyo Branch
Never touch LED light sources and their surroundings.
The light sources and their surroundings are very hot, so an accidental touch might cause a burn.
To ensure brightness and safety, carry out periodical cleaning and inspection.
If used in an extended period without maintenance or inspection, a smoke, fire or electric shock might result.
Head Office
+81 774 55 8181
L高照般4
+81 3 5833 8971
+81 774 58 2034
Phone
Phone
36 Shinike, Terada, Joyo, Kyoto Pref. 610-0192 Japan
Fax
2-19-6 Yanagibashi, Taito-ku, Tokyo 111-0052 Japan
For a product marked with a frequency, don’t use the product at a frequency other than 50 or 60 Hz (local power supply
frequency). Use at a wrong frequency might cause a fire.
- 2 /2 -
Table of contents
Popular Lantern manuals by other brands

Seto
Seto ALDEBARAN 5000 Instructions for use

Tracon Electric
Tracon Electric STLCAMP10W user manual

North Coast Lighting
North Coast Lighting 522PHM Series Assembly and installation instructions

Hess
Hess BURGOS Installation and operating instructions

less'n'more
less'n'more Athene A-SL General Instructions for Use

IKEA
IKEA SOLVINDEN J2003 manual