Selecon Studio Panel Installation and operating instructions
85-6384 1
Studio Panel LED Luminaires MANUAL ADDENDUM
MANUAL ADDENDUM - PLEASE READ
1. Overview
This MANUAL ADDENDUM provides information in addition to the Installation and User’s Manual supplied with
the unit. Please review this document - as well as the supplied manual - carefully before using the Studio Panel LED
Luminaire.
Some notes about this document:
• Your Studio Panel LED Luminaire has been updated with the latest firmware (version 1.2 or later).
• Please refer to the new menu categories and options table and custom recording options below.
• Table 1 in this addendum supersedes Table 5 on page 13 of the installation and user's manual.
2. Updated Menu Categories and Options
Note: All options in grey shading are added in software version 1.2 (or later). All other options remain unchanged.
Table 1: Menu Categories and Options (Software Version 1.2 and later)
Category Options Next Level Meaning
Mode
Manual
(Manual
mode, local
control only
(no DMX)
Setting
Factory
Dimmer
Rotate wheel to set
dimmer level from 0 to
100% (in 1% increments)
CCT
Rotate wheel to set CCT
level from 3000K to 6000K
(in 1K increments)
Custom
Preset (01 - 09)
Allows users to set and
adjust Presets, Dimmer,
and WW / CW (CCT) to
their specific requirements.
Dimmer (0 - 100%)
WW (Warm White) 0-
100% CW (Cool
White) 0-100%
DMX-8B
(Unit is set to
operate in
DMX512 8-
Bit mode)
Address Sets the units DMX512
address (from 001 to 512)
LastHold
Sets the units operation
should DMX512 signal be
disconnected or lost - YES
(maintain last DMX512
state) or NO (do not
maintain last DMX512
state)
State
Information only - displays
if DMX512 is present
(connected) or not
DMX-16B
(Unit is set to
operate in
DMX512 16-
Bit mode)
Address Sets the units DMX512
address (from 001 to 512)
LastHold
Sets the units operation
should DMX512 signal be
disconnected or lost - YES
(maintain last DMX512
state) or NO (do not
maintain last DMX512
state)
State
Information only - displays
if DMX512 is present
(connected) or not
MANUAL ADDENDUM Studio Panel LED Luminaires
285-6384
3. Recording and Saving a Custom Preset
Table 2: New Menu Categories and Options
To record / edit a custom preset:
CAUTION: Do not power down the unit before waiting at least five seconds has passed after completing the steps
below to record and save a custom preset. Powering the unit down before waiting five seconds will erase the custom
preset.
Step 1. In Manual Mode:
a. If Setting Custom is displayed, proceed to Step 2.
b. If Setting Factory is displayed, you must:
1) Press navigation wheel once.
2) Rotate navigation wheel until Setting Custom is
displayed.
3) Press navigation wheel once. Proceed to Step 2.
Step 2. Rotate navigation wheel to desired preset number (1, 2, 3, 4...9)
Step 3. Press navigation wheel once.
Step 4. Rotate navigation wheel to Dimmer.
Step 5. Press navigation wheel once.
Step 6. Rotate navigation wheel to desired intensity (0-100%)
Step 7. Press navigation wheel once.
Step 8. Rotate navigation wheel to ww cw.
Step 9. Press navigation wheel once.
Step 10. Rotate navigation wheel clockwise or counter-clockwise to desired
color temperature (0-100% 0-100%).
Step 11. Press navigation wheel once.
Step 12. Once complete, preset and its associated settings will be
automatically saved after five seconds.
For assistance regarding the use of this product or this new feature, please
contact customer service at +1.214.647.7880 or you local Authorized
Selecon Dealer.
Category Options Next Level Meaning
Mode Manual Setting Custom
Preset (01 - 09)
Allows users to set and
adjust Presets, Dimmer,
and WW / CW (CCT) to
their specific requirements.
Dimmer (0 - 100%)
WW (Warm White) 0-
100% CW (Cool
White) 0-100%
Rotate Navigation Wheel, in either
direction, to scroll through menu options.
Press Navigation Wheel once to select a
menu option.
