Sennheiser e614 User manual

e 614
Bedienungsanleitung
Instruction manual
Notice d‘emploi
Istruzioni per l‘uso
Instrucciones de uso
Manual de utilização
Gebruiksaanwijzing
Инструкция по эксплуатации
使用说明
Stage Microphones

B


1
2
125 Hz
250 Hz
500 Hz
1,000 Hz
2,000 Hz
4,000 Hz
8,000 Hz
16,000 Hz
30°
0°
180°
150°
120°
60°
90°
0
5
10
15
20
25
dB
30°
0°
180°
150°
120°
60°
90°
- 50
- 60
- 70
- 80
- 90
- 40
dBV
0°, 1 m
0°, 5 cm
CA
12
3
12
3
+ +
12
3
XLR6.3 mm
+
+
12
3
XLR
+
XLR
12
3
6.3 mm
+
+
symmetrical
XLR
XLR
+
D

ENFRITPTNLRUZH ES DE
1
Important safety information
• Please read this instruction manual carefully and completely befo-
re using the product.
• Make this instruction manual easily accessible to all users at all
times.
• Always include this instruction manual when passing the product
on to third parties.
Before operation
• Never open the housing of the product. If products are opened by
customers in breach of this instruction, the warranty becomes null
and void.
• Only use attachments, accessories or spare parts specified by
Sennheiser.
During operation
• Liquids entering the product can short-circuit the electronics or
damage the mechanics. Keep all liquids away from the product.
• Solvents or cleansing agents can damage the surface of the
product. Only use a soft, slightly damp cloth to clean the product.
• Do not expose the product to extreme temperatures.
After operation
• Handle the product with care and store it in a clean, dust-free
environment.
Intended use
Intended use includes:
• having read this instruction manual, especially the chapter
“Important safety information”,
• using the product within the operating conditions and limitations
described in this instruction manual.
“Improper use” means using the product other than as described in
this instruction manual, or under operating conditions which differ
from those described herein.
e614_511652_0117_SP9.indb 1 05.01.2017 14:24:17

2
The e 614
The super-cardioid e 614 is a pre-polarised condenser microphone
designed for demanding applications which require a wide frequency
response, high sound pressure level, fast transient response and a com-
pact design. With its frequency response of 40 Hz to 20 kHz, the e 614 is
able to capture the full sound of the instrument, while its super-cardioid
pick-up pattern isolates the microphone from other on-stage signals.
An excellent microphone for overheads, hi-hat and percussions, the
e 614 is also an ideal choice for wood-wind and string instruments.
Its excellent acoustic properties also make it a valuable tool for home
recording, the project studio and live stereo pair recording.
Features
• Condenser microphone
• Excellent directivity across the entire extended frequency range
(40-20,000 Hz)
• Natural sound for flexible applications
• Designed for high SPLs
• Sturdy metal housing
Package contents
1 e 614 microphone
1 Pouch
1 MZQ 100 microphone clamp
1 Instructions for use
Product overview A*
1 Sound inlet basket
2 XLR-3 connector
Diagrams can be found on the cover pages.
*
e614_511652_0117_SP9.indb 2 05.01.2017 14:24:17

ENFRITPTNLRUZH ES DE
3
Using the microphone
Positioning the microphone B
Drums / Percussions
Pos. Resulting sound Commentary
B.1 • Natural, clear
sound
Position the microphone a few
centimetres above the outer edge
of the hi-hat aiming down. If
necessary, remove unwanted low-
frequency signal portions by high
pass filtering.
Attention: When closing the hi-
hat, a strong air current is created
on the edge. If the microphone is
positioned too close to the edge,
interfering noise due to the air
current can occur.
B.2 • More fundamental,
little overtones
In order to prevent interference due to crosstalk between adjacent
sound sources, try to position the microphone so that the interfering
sound source is located in the angle area of the highest cancellation of
the microphone (approx. 135°; see polar diagram)
Cleaning and maintaining the e 614
Caution Liquids can damage the electronics of the product!
Liquids entering the housing of the product can cause
a short-circuit and damage the electronics.
X
Keep all liquids away from the product.
X
Do not use any solvents or cleansing agents .
XUnscrew the sound inlet basket 1.
XRemove the foam insert from the sound inlet basket 1.
XUse a slightly damp cloth to clean the sound inlet basket 1 from
the inside and ouside.
XReinsert the foam insert into the sound inlet basket 1and replace
the sound inlet basket on the microphone and screw it tight.
e614_511652_0117_SP9.indb 3 05.01.2017 14:24:17

4
Specifications
Transducer principle pre-polarised condenser
microphone
Frequency response 40....20,000 Hz
Pick-up pattern super-cardioid
Sensitivity (free field, no load at
1 kHz)
3 mV/Pa
Nominal impedance 50 W
Min. terminating impedance 1 kW
Phantom powering 12 – 52 V / 3 mA
Connector XLR-3
Dimensions Ø 20 mm, L 100 mm
Weight 93 g
Max. sound pressure level at 1 kHz 139 dB/SPL
The polar diagram and the frequency response curve Ccan be found on
the cover pages.
The XLR-3 connector assignment Dcan be found on the cover pages.
Manufacturer Declarations
Warranty
Sennheiser electronic GmbH & Co. KG gives a warranty of 24 months
on this product.
For the current warranty conditions, please visit our website at
www.sennheiser.com or contact your Sennheiser partner.
FOR AUSTRALIA ONLY
Sennheiser goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation for any other reason-
ably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
This warranty is in addition to other rights or remedies under law.
Nothing in this warranty excludes, limits or modifies any liability of
Sennheiser which is imposed by law, or limits or modifies any remedy
available to the consumer which is granted by law.
To make a claim under this warranty, contact
Sennheiser Australia Pty Ltd, Unit 3, 31 Gibbes Street Chatswood NSW
2067, AUSTRALIA.
Phone: [phone], email: [email protected].
All expenses of claiming the warranty will be borne by the person
making the claim.
e614_511652_0117_SP9.indb 4 05.01.2017 14:24:17

ENFRITPTNLRUZH ES DE
5
The Sennheiser International Warranty is provided by Sennheiser
Australia Pty Ltd (ABN 68 165 388 312), Unit 3, 31 Gibbes Street
Chatswood NSW 2067 Australia.
In compliance with the following requirements
• WEEE Directive (2012/19/EU)
Please dispose of this product at the end of its operational
lifetime by taking it to your local collection point or recycling
center for such equipment.
CE Declaration of Conformity
• RoHS Directive (2011/65/EU)
The declaration is available at www.sennheiser.com/download.
e614_511652_0117_SP9.indb 5 05.01.2017 14:24:17

e 608
e 614 e 609 silver e 604 e 602-II e 835 e 845 e 865 e 901
e 902 e 904 e 906
e 908 e 914 e 935 e 945
e 965

Sennheiser electronic GmbH & Co. KG
Am Labor 1, 30900 Wedemark, Germany
www.sennheiser.com
Printed in Germany, Publ. 01/17, 511652/A04