Sprout LK-6060-5x2 User manual

1
Simple. Modern. American Made.
Adult assembly only
2 Adults required for assembly
Assemble completely before use
Double Row
Lockers

(10) Pegs
with Hole
O
(80) Pins
(4 per Shelf)
L
BEFORE YOU START
REQUIRED:
Wood glue is
used to
permanently
attach the door
pegs. Using
other glue types
may aect
curing and
workability time.
RECOMMENDED:
A rubber mallet
can help push
pieces together.
Or use a hammer
with a scrap
piece of wood or
a cutting board
placed over the
surface for
protection.
(2) Toes
C
(2) Backs
D
E
(1) Left Side (1) Right Side
F(4) Vertical
Dividers
G
I
(8) Doors (2) End Doors
J
(20) Shelves
(2 per cubby)
K
(80) Short Screws
(4 per hinge part)
S
(10) Long
Screws
M
(10) Washers
N
REQUIRED: A
phillips head
screwdriver.
A drill with a
phillips head
driver can also
be used, but is
not required.
(10) Pegs
with Knob
P
(20) Hinge
Clips
Q
(20) Hinges
R
(1) Bottom
A
(1) Top
B
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. LK-6060-5x2PAGE 2 OF 12
(1) Horizontal Divider
H
PARTS

*When inserting tabs into slots make sure the side with the wider lip on
the tab faces the same direction as the notch in the slot.
NOTCH
WIDE LIP
SLOT TAB
TAB ORIENTATION
PREPARE PARTS
Install Toes C by placing tabs into slots on Bottom A as
shown below. Ensure to orient parts according to
guidelines above. Push to tighten.
1
Frustrated?
Need Help?
STOP Talk to our customer service agent at:
[phone]
A
A
C
C
GLUE
I
Install Pegs K on Back D by inserting Long Screw L
through holes with Washer M , then thread on Peg.
2
III
Install Pegs O on Doors H and I by applying a dot of
glue to bottom of the slot and a thin layer to end of the Peg.
Insert Peg into slot on each door. Wipe o excess glue
with a damp cloth. Ensure to apply glue just before
connecting parts together.
3
O
O
D
D
M
M
N
N
P
O
I
I
J
DOCUMENT: AI-LK-5x2 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2022 PAGE 3 OF 12

QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. LK-6060-5x2PAGE 4 OF 12
Install Hinges Q into slots on all Doors ( I & J ) by
screwing (2) Short Screws R into pilot holes on Door, as
shown below.
4
Install Hinge Clips P by screwing (2) Short Screws R
into pilot holes indicated on Left Side E and Vertical
Dividers G . Make sure that the Adjustment Screw is
facing forward, as shown.
5
I
I
J
S
S
R
R
E
G
S
Q
PILOT HOLES
EG
ADJ. SCREW
FACE FORWARD
E
S
Q

Orientation of Horizontal and Vertical Dividers ( H & G ) is very
specic. If done incorrectly, Doors may close the wrong
direction and Backs may be upside down. To help with
orientation, lay out parts as indicated below:
*HG
2 Adults Required for Assembly
ASSEMBLY INSTRUCTIONS
TOP VIEW
DOCUMENT: AI-LK-5x2 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2022 PAGE 5 OF 12
A
E
Left Side
F
Right Side
H
Horizontal Divider
B
Top
Bottom
4 Slots for Back
3 Slots for Back D
D

With the help of another adult, insert Vertical Dividers G
through slots on Horizontal Divider H . Vertical Dividers
should be oriented with the hinge clips down, facing
Right Side F according to * .
1
H
G
HINGE CLIPS ON
BOTTOM-RIGHT
MIDDLE SLOT
FORWARD-UP
G
G
G
G
H
F
Insert tabs for Backs D into corresponding slots on
Horizontal Divider H .
2
H
D
D
D
H
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. LK-6060-5x2PAGE 6 OF 12
*

DOCUMENT: AI-LK-5x2 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2022 PAGE 5 OF 12
BA
Align tabs for Vertical Dividers G and Back D with the
slots on Top B and Bottom A . Then, pop tabs for Back
and Dividers into slots from one side to the other, as
shown.
3
Tighten Top B and Bottom A into place by pushing
down on the ends and middle of each part, as shown
below.
4
G
B
D
A
D
G
B
A
BA

QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. LK-6060-5x2PAGE 8 OF 12
Pop Sides E and F onto tabs, as depicted below. Books
can be placed under Top B and Bottom A to provide
more room if needed.
5FE
E
B
B
A
A
F
Tighten Sides E and F into place by pushing down on
the ends and middle on each Side, as shown below.
6FE
E
F

DOCUMENT: AI-LK-5x2 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2022 PAGE 9 OF 12
Carefully tilt assembly up onto feet. Insert Shelf Pins L
into pin holes at the desired height and rest Shelf K on
Pins. Each individual locker cubby should have (2)
Shelves, and each Shelf will use (4) Pins.
7
K
L
K
L

Doors H and I will need to be installed from left to
right. Note that the End Door I has a small circular
groove on the inside face, as depicted below.
1
DOOR ASSEMBLY
I J
J
I
I
I
I
I
I
I
I
I
J
J
SMALL GROOVE
ON INSIDE FACE
J
To install Door H , carefully attach Hinge Q to Hinge
Clip P by inserting as shown below.
2
Locker Side
Q
R
I
I R
Q
START HERE
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. LK-6060-5x2PAGE 10 OF 12

To take Door H o push on lever and rotate Hinge Q
to release it from Hinge Clip P .
4
Adjust Door H to align ush with outer edges of unit
using the Adjustment Screws as shown below.
5
Repeat steps with the rest of the Doors H and I .
Due to the natural variances found in wood, the grain,
color, and shade of the doors may dier. With this in
mind, arrange doors according to your preference, with
the exception of End Doors I .
*
ADJ. SCREW
SIDE TO SIDE
ADJ. SCREW
UP AND DOWN
ADJ. SCREW
IN AND OUT
I J
J
Locker Side
Q
Q
R
R
I
I
I
I
Locker Side
Once in position, push the Hinge Q lever and rotate
Hinge ush with the Locker Side until Hinge is locked
into Hinge Clip P .
3
Q
Q
R
R
I
DOCUMENT: AI-LK-5x2 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2022 PAGE 11 OF 12

Simple. Modern. American Made.
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. LK-6060-5x2PAGE 12 OF 12