Sentiotec COUNTRY Installation instructions

Garden sauna COUNTRY
319 x 264 x 290 cm
Assembly Instruction
DE
EN
FI
Version 10/17

Assembly instructions
EN
Garden sauna
COUNTRY
Exterior dimension:
319 x 264 x 290 cm
Interior dimension:
200 x 200 x 210 cm
Wall thickness:
70 mm
There may be slight deviations in the dimensions.
Subject to technical modifications and misprints.
Dear customer,
Before you begin with the work, check that all the individual parts have been delivered against the parts list.
Ifyou discover any missing parts, notify your dealer within 14 days of receiving the sauna cabin.
Keep the delivery note, the invoice and the assembly instructions in
asafeplace in case of any questions.
You require the following tools:
1 hammer with a wooden head or a rubber hammer
1 cordless screwdriver with bits for cross-head screws and Torx
1 roller tape measure
1 drill bit Ø10 mm; 1 drill bit Ø3 mm
1 spirit level
1 pencil
You need an assistant for the assembly. We also advise you to pre-drill
theholesforthescrews.
02
The electrical connection may only be performed by a qualified electrician or similarly
qualified person.
!

Front face with doors
1 block plank 230 x 6.5 x 7 cm with recess for
door frame and 4 recesses for threaded rods
13 block planks 69 x 14.6 x 7 cm with electrical
installation drill holes
1 block plank 69 x 14.6 x 7 cm with electrical
installation drill holes and 3 drill holes for supply air
14 block planks 69 x 14.6 x 7 cm
2 block planks 230 x 14.6 x 7 cm over door frame
with 4 recesses for threaded rods
1 roof 230 x 48.5 x 7 cm
2 interior door panels 86 x 5.5 x 2 cm
2 interior door panels 201 x 5.5 x 2 cm
Right and left sides
26 block planks 230 x 14.6 x 7 cm
2 block planks 252.5 x 14.6 x 7 cm
2 block planks 275 x 14.6 x 7 cm
2 block planks 297.5 x 14.6 x 7 cm
2 block planks 319 x 17 x 7 cm
Rear face
1 block plank 230 x 6.5 x 7 cm with 2 recesses
forthreaded rods
1 block plank 230 x 14.6 x 7 cm
with ventilation recess
15 block planks 230 x 14.6 x 7 cm
with 2 drill holes
1 roof 230 x 48.5 x 7 cm
3 block planks for roof 319 x 13.6 x 7 cm
2 roof support slats 200 x 4 x 4 cm
2 roof support slats 192 x 4 x 4 cm
2 roof elements 199 x 99 x 6.5 cm
2 oor frames 214 x 8 x 4 cm
3 oor frames 206 x 8 x 4 cm
2 oor frames 206 x 12 x 4 cm
22 oor boards 199.5 x 9.5 x 1.9 cm
4 skirting boards 200 x 2.5 x 2.5 cm
70 roof boards 142 x 9.5 x 1.8 cm
2 weather boards 319 x 4 x 2 cm
4 weather boards 145.5 x 12.5 x 1.9 cm
5 bench support slats 4 x 4 cm (2 pcs. 58 cm;
2 pcs. 116 cm; 1 pc. 48 cm)
1 bench 137.5 x 62 cm
2 benches 199 x 62 cm
2 back rests
2 head rests
1 bench screen 199 cm
1 door frame 198 x 90 cm
1 interior light
1 light screen
1 oor grid 70 x 50 cm
1 heater safety guard, 2 parts
1 ventilation shutter
1 assembly material set
1 assembly instruction manual
6 threaded rods 8 mm incl. nuts
3 silicon cables 5-pin 5 x 1.5 mm²
20 m² roong felt
1 insect screen
COUNTRY parts list
The parts list can also be used as a claims sheet.
03

04
GARDEN SAUNA COUNTRY
Notes for the planning permission, foundation,
anchorage, delivery and unloading
Planning permission
Before installing the garden sauna, make sure you enquire about whether planning
permission is required at your local planning authority (municipal oce, magistrate).
Youmay need this as permission is required above a certain room volume. This depends
on where you live exactly and is therefore handled dierently from country to country.
Check with your local planning authority (municipal oce, magistrate)
with respect to the building regulations and load standards.
Concrete foundation:
A solid concrete foundation is important for the durability as well as the safety of your
garden sauna.
We recommend having the foundation laid by a specialist.
It is the basis for a proper anchorage of your garden sauna. Only then can you ensure
that there will be no diculties with assembly and use.
There are several ways that you can lay the foundation for your garden sauna.
Assembly instructions
EN

05
However, the two options below have proven to be the best in practice:
• Foundation slab (base plate)
• Strip foundation
For both types, a foundation that is absolutely at and load-bearing must be ensured.
Only then can the assembly of the individual modules be ensured without any diculties
and with a precise t.
Once the concrete slab has been completed and dried out, we recommend torching it
with roong felt or torch-on felt in order to seal it completely.
Foundation slab (base plate)
A base plate ensures a frost-proof foundation for the garden sauna. Note that structural
steel mesh mats must be laid in the concrete (reinforced) in order to achieve maximum
stability and protect the slab from cracking.
Ground Concrete 15 cm thick
Gravel 15 cm thick PE-lm

06
Strip foundation
Depending on the structural requirements and local conditions, strip foundations can be
laid in dierent ways. There are two types of strip foundations:
• strip foundation - not reinforced
• strip foundation - reinforced
To make a frost-proof strip foundation, you must dig at least 80 cm deep into the ground.
The supporting walls of the garden sauna are then laid on the foundation strips.
This construction has the advantage that the base plate can be thinner and less
reinforcement is necessary.
The foundation should be about 10 to 15 mm smaller than your garden sauna so that
water can run o the outer walls of the sauna and the outer sides of the foundation.
Assembly instructions
EN
Ground Concrete 10 cm thick
Gravel 10 cm thick
PE-lm
80 cm
30 cm

07
Note:
The foundations must be absolutely at to ensure the load-bearing capacity of the sauna.
Ifthe foundation slab is larger than the oor space of the garden sauna, rainwater can start
to collect around the sauna This means that the wooden wall elements would be constantly
standing on wet ground.This could result in the wood absorbing the water and starting to rot.
We point out that we do not accept any liability for the resulting damage.
Anchoring the garden sauna:
It is essential that the garden sauna is rmly anchored on the base plate or the strip
foundation. Strong winds can exert a powerful force on the garden sauna. To prevent
damage to your property or third-party property, proper anchoring is essential.
We point out that anchoring the garden sauna is the responsibility of the customer and we
do not accept any liability for accidental damage.
Wood protection outside:
The wood of the garden sauna is untreated. If you want to increase the life of your garden
sauna, we recommend painting with a suitable protective painting.
Roong:
The included roong felt serves as an initial cover. We also recommend to cover the roof
with bitumen shingles, sheet metal or a suitable foil.
Delivery of the garden sauna:
The garden sauna is delivered by lorry (also possible by semi-trailer truck).
Access to the unloading area must be ensured.
At least two people are required for unloading and installing the garden sauna.

Screws 5 x 100 mm
08
1 block plank 230 x 6.5 x 7 cm with recesses for threaded rods
Assembly instructions
EN
Fig. 1.3
1 block plank 230 x 6.5 x 7 cm with recesses for threaded rods and doors
Fig. 1.1
Fig. 1.2
Screws 4 x 60 mm
Base frame for
outer sauna

09
Fig. 1.4
Fig. 1.5
1 block plank 230 x 14.6 x 7 cm with ventilation recess
1 block plank 69 x 14.6 x 7 cm with drill holes for supply air

10
Fig. 1.7
Threaded rods 8 mm
Assembly instructions
EN
Fig. 1.6
Fig. 1.8
13
12
11
10
14
15
09

11
Screw joints at bottom
Fig. 1.9
Fig. 1.11
Fig. 1.10
Screw joints at top – cut o the remaining
threaded rod above the nut

12
Ventilation shutter
4 screws 3 x 40 mm
Assembly instructions
EN
Fig. 1.13
Fig.1.12

13
Fig.1.21
Skirting board - screws 3.2 x 40 mm
Screws 5 x 100 mm
Fig. 1.14
Fig. 1.15
Floor - screws 3.5 x 50 mm

14
Measure from oor to
thebottom edge of the
roof support slat 206 cm.
Assembly instructions
EN
Screws 4 x 70 mm
Fig. 1.16
Fig. 1.17
206 cm

15
Fig. 1.19
Fig. 1.18
Screw the roof elements from above with the support slats Screws x 80 mm

16
Fig. 1.21
Screws 5 x 70 mm
Fig. 1.20
Assembly instructions
EN
41 cm
87 cm

17
Fig. 1.22
Screws 3.5 x 50 mm
Fig. 1.23
Bench screen
- view from rear
Bench screen

18
Assembly instructions
EN
Fig. 1.24
Fig. 1.25 Fig. 1.26 Fig. 1.27
Screws 3.5 x 50 mm
25 cm
4 screws 3 x 40 mm

19
First put the mounting slats of
thedoor and the screws in the cabin.
Then place the door element in the
doorway, take the top slat (1), place
itso that left and right is the same
andscrew the slat to the door.
Next, screw on the side mounting
slats. (2). Finally, screw on the
bottomslat.
Screws 3 x 40 mm
1.
2.
Fig. 1.34
Fig. 1.33

20
Screws 3 x 40 mm
Fig. 1.36
Fig. 1.35
Assembly instructions
EN