Sentiotec ARKTIS INFRA + User manual

EN
ARKITS-IR+
Version 12/18 item no. 1-030-271
INSTRUCTIONS FOR INSTALLATION AND USE
English
Solid wood sauna
ARKTIS
INFRA +
234 x 206 x 204 cm

Table of Contents
1. Preparing for installation 3
1.1. Tools required 4
1.2. Maintenance and cleaning 5
1.3. Disposal 5
1.4. ARKTIS INFRA+ parts list 6
2. Cabin installation 9
2.1. Base frame installation 9
2.2. Wall element assembly 10
2.3. Ceiling installation 17
2.4. Ventilation slit installation 19
2.5. Installing interior ttings 19
2.6. Installing accessories 26
2.7. Installing glass door 28
2.8. Installing roof trim 31
2.9. Installing ceiling cover slat 32
3. Floor plan 33
3.1. Left oor plan 33
3.2. Right oor plan 34
3.3. Changes for the right oor plan installation 35

EN
Instructions for installation and use p. 3/36
1. Preparing for installation
Read these assembly instructions carefully and keep them within reach when
using the sauna so that you can look up product information at any time.
Important note:
●Before you begin work, check the parts list to ensure that all the individual
parts have been delivered. If you discover any missing parts, notify your
dealer within 14 days of receiving the sauna cabin.
●The room that the sauna is installed in must be dry and ensure an appropriate
amount of air circulation.
● The oor must be level and even, preferably a stone or tiled oor.
●A minimum room height of 230 cm is required for the cabin installation work.
●A distance of at least 5 cm from the wall must be maintained.
●The inside of the wooden parts used must not be handled with any impreg-
nating material.
●You need an assistant for the installation.
●Wood is a natural product that can swell, shrink or warp, despite good stor-
age. For this reason, some force may be necessary during the installation.
● All screw ttings must be pre-drilled.
Attention!
The electrical connection may only be performed by a qualied electrician
or similarly qualied person.
These assembly instructions can also be found in the downloads section
of our website: www.sentiotec.com/downloads.

Instructions for installation and use p. 4/36
1.1. Tools required
●Hammer with a wooden head or a mallet
●Cordless screwdriver with bits for cross-head screws and Torx
●Roller tape measure
●Drill bits with a diameter of 3 mm, 10 mm, 20 - 30 mm
(for sauna heater power cable)
●Spirit level
●1.5 mm hexagonal socket wrench
●Utility knife
●Ladder
●Backsaw
60 cm
80 cm
100 cm
This symbol indicates tips and useful information
Pre-drill
Cut to real measurement with backsaw
Check the right angle:

EN
Instructions for installation and use p. 5/36
1.2. Maintenance and cleaning
●The sauna should be cleaned with a damp cloth. Only use warm water – no
cleaning products.
●We recommend heating the cabin once a month if the sauna is not used for
a long time.
Pitch pockets are not grounds for return, since they can always appear in
spruce wood and the depth at which they lie cannot be detected during
the sorting-out process.
If these are just under the surface, heat can cause them to soften and
“bleed”.
The leaking pitch can be removed with a rag soaked in acetone. If only
droplets of pitch occur, allow these to harden and then carefully scrape
them off with a knife.
1.3. Disposal
●Please dispose of packaging materials in accordance with the appli-
cable disposal regulations.
●Used units contain reusable materials as well as hazardous substanc-
es. Therefore, do not dispose of your used unit with household waste,
but rather do so in accordance with the locally applicable regulations.

Instructions for installation and use p. 6/36
Base frame
2 Base frame 204 x 9 x 4 cm
1 Base frame 138 x 9 x 4 cm
1 Base frame 61.5 x 9 x 4 cm
1 Base frame 32 x 9 x 4 cm
Wall elements
1 A/B wall elements with heater recess 193 x 48 x 4 cm
1 A/B wall elements 193 x 48 x 4 cm
1 A/B wall elements with Multiclip 193 x 48 x 4 cm
1 A/B ventilation element with Multiclip 193 x 48 x 4 cm
1 A/A wall element with Multiclip 193 x 44 x 4 cm
1 A/A electrical element with Multiclip 193 x 44 x 4 cm
1 A/A wall element 193 x 44 x 4 cm
1 A/A wall element with Multiclip 193 x 55.5 x 4 cm
2 A/B wall element with Multiclip 193 x 55 x 4 cm
1 A/B wall element with heater recess 193 x 55 x 4 cm
1 A/B wall element 193 x 55 x 4 cm
1 Element above glass 45.5 x 8.6 x 4 cm
1 Element above glass 44 x 8.6 x 4 cm
Ceiling elements
1 A/B ceiling elements 194 x 55 x 4 cm
1 A/B ceiling element 194 x 56 x 4 cm
1 A/A ceiling element 138.6 x 56 x 4 cm
1 A/A ceiling element, diagonal 194 x 55 x 4 cm
Corner posts
3 90° corner posts with Multiclip 193 x 6 x 6 cm
2 45° corner posts next to door with Multiclip 202 x 7.8 x 4 cm
1 Corner post 90° with groove and Multiclip 202 x 7.8 x 4 cm
1 Post for glass element, 8 mm groove with Multiclip 202 x 4.5 x 4 cm
No. of
items Name Dimensions
1.4. ARKTIS INFRA+ parts list

EN
Instructions for installation and use p. 7/36
No. of
items Name Dimensions
Support slats
2 Roof support slat 115 x 4 x 4 cm
1 Roof support slat 196 x 4 x 4 cm
1 Roof support slat 136 x 4 x 4 cm
1 Roof support strip 1x 22.5 ° 54 x 4 x 4 cm
1 Roof support slat 1 x 22.5° 112 x 4 x 4 cm
1 Roof support slats 2 x 22.5° 86.5 x 4 x 4 cm
2 Roof support slat 114 x 1.2 x 4 cm
1 Roof support slat 200 x 1.2 x 4 cm
1 Roof support slat 140 x 1.2 x 4 cm
1 Roof support slat 1 x 22.5° 54.8 x 1.2 x 4 cm
1 Roof support slat 1 x 22.5° 114.8 x 1.2 x 4 cm
1 Roof support slat 2 x 22.5° 86.5 x 1.2 x 4 cm
1 Bench support slat 1 x 45° 116 x 4 x 4 cm
1 Bench support slat 110 x 4 x 4 cm
3 Bench support slats 58 x 4 x 4 cm
2 Mounting slats for bench screen 26 x 4 x 4 cm
Interior ttings
2 Benches 195 x 62 x 9 cm
1 Bench 161.5 x 62 x 9 cm
1 Bench cover slat 45.7 x 14 x 2 cm
1 Backrests 122 x 26 x 5 cm
1 Backrests 105 x 26 x 5 cm
1 Backrests 67 x 26 x 5 cm
1 Backrests 56 x 26 x 5 cm
1 Bench screen 195 x 35 x 5 cm
1 Heater safety guard, 3 parts 65.5 x 475 x 75 cm
1 x 65.5 x 75 cm, 2x 45.5 x 55 cm
1 Floor grid 70 x 53 x 4 cm
2 Headrests 43 x 25 x 7 cm
1 Lamp protection grille 38 x 32 x 4 cm
1 Ventilation slit 52 x 14 x 1.5 cm

Instructions for installation and use p. 8/36
Glass elements
1 Glass door 191.5 x 68 x 0.8 cm
1 Glass element 194.5 x 48.1 x 0.8 cm
1 Glass element 194.5 x 46.4 x 0.8 cm
Roof trim slats
1 Roof trim slat 1 x 45° 151 x 6 x 4 cm
1 Roof trim slat 1 x 22.5° and 1 x 45° 56.3 x 6 x 4 cm
1 Roof trim slat 1 x 22.5° 123.5 x 6 x 4 cm
1 Roof trim slat 2 x 22.5° 84.9 x 6 x 4 cm
Accessories
1U aluminium prole 45.7 x 1.2 x 1.5 cm
1U aluminium prole 44 x 1.2 x 1.5 cm
1 Door handle set wood/stainless steel
1 2 door hinges 3308
1 Door magnet, sleeve plate
1 Sauna lamp
1 3 Silicon cables: 5 x 2.5 mm²
1 3 Silicon cables: 3 x 1.5 mm²
2 Infrared radiator ECO-350-R 1-027-785
1 Infracontrol mini 1-035-976
1 Cover panels for Infracontrol mini (2 items) 1-035-503
1 Distributor 1 to 2 1-028-731
1 Cable GST18i/35 - GST 18i/3B 1-028-862
2 Prestige radiator covers 71 x 21 x 5 cm
1 Template for Multiclip installation
1 Installation material set
1 Assembly instructions
No. of
items Name Dimensions

EN
Instructions for installation and use p. 9/36
2. Cabin installation
The cabin can have a right or left set-up; please note the corresponding oor
plans on Page 33 and Page 34.
2.1. Base frame installation
Left oor plan
204 cm + 32 cm
61.5 cm
138 cm
204 cm
3 mm drill bit, 4 screws 4 x 70 mm
Right oor plan
138 cm
204 cm
61.5 cm
3 mm drill bit, 4 screws 4 x 70 mm
204 cm + 32 cm

Instructions for installation and use p. 10/36
2.2. Wall element assembly
The corner posts are connected to the wall elements using Multiclips. The other
wall elements are connected tongue and groove and are screwed together.
Left oor plan
*
*
* *
*
*
*Multiclips
Attention!
The installation subsequently described is for the left oor plan. For changes
affecting the installation for the right oor plan, see Page 34.
*
*
Aalways refers to the visible side. This is labelled on the top side of
the wall elements.
*
*

EN
Instructions for installation and use p. 11/36
Pre-assemble the wall elements with the corner posts on the oor and
then place these posts on the base frame.
Insert the corner post from above down onto the wall elements. When doing this,
ensure that the Multiclips are correctly aligned (see below). The corner post must
be ush with the wall elements.
Multiclip
Installing corner posts with wall elements

Instructions for installation and use p. 12/36
Installing wall elements
The electrical element has drill holes for laying cables. For the position
see oor plans on Page 33 and Page 34.
Width 48 cm
Width 55 cm
Width 55.6 cm
Electrical element

EN
Instructions for installation and use p. 13/36
Screwing wall elements together
3 mm drill bit, 8 screws 4 x 70 mm
Check the right angle before screwing the wall elements together.
Observe the tip on page 4.

Instructions for installation and use p. 14/36
Corner post and post for glass

EN
Instructions for installation and use p. 15/36
Glass elements
3 mm drill bit,
1 screw 4 x 70 mm
3 mm drill bit,
1 screw 4 x 70 mm

Instructions for installation and use p. 16/36
Remove transport strip from
the door frame
Insert door frame
Türstock einsetzen

EN
Instructions for installation and use p. 17/36
Insert door frame
2.3. Ceiling installation
Roof support slats
4 cm
21 screws 4 x 70 mm

Instructions for installation and use p. 18/36
Ceiling elements
3 mm drill bit, 15 screws 4 x 70 mm

EN
Instructions for installation and use p. 19/36
2.4. Ventilation slit installation
2.5. Installing interior ttings
Bench support slats
2 screws 4 x 60 mm
3 mm drill bit, 3 screws 5 x 70 mm
3 mm drill bit, 4 screws 3.5 x 40 mm
82 cm

Instructions for installation and use p. 20/36
3 mm drill bit, 3 screws 5 x 70 mm
36 cm
82 cm
3 mm drill bit, 3 screws 5 x 70 mm