SEON HD1Q User manual

HD1Q Dome Camera with Angle Mount Shim
Quick Install Guide
© Seon Design Inc. | July 2017 | All rights reserved.
www.seon.com Part Number: 700-1094 R2
Camera Kit:
• 1 HD1Q camera, including dome, gasket,
and connector cable
• 3 x No. 10 screws with washers
(1” length, part # 600-1012)
* not used for shim installations
• 1 Security key (part # 645-1003)
• 1 Quick Install Guide (part # 700-1084)
* not used for shim installations
• 1 Drilling template (Part # 700-1090)
* not used for shim installations
WARNING: Cable Compatibility
This camera requires a special Analog High Denition (AHD) cable - as indicated by a blue band
in front of the connectors. The AHD cable is not included with the camera kit. If you require an
AHD Cable, please contact our customer service department to place an order.
Specications
Power Consumption 1 W (IR o); 2 W (IR on)
Operating Voltage Range 12 VDC ± 10% (powered by DVR)
Operating Temperature Range -4 to 122ºF (-20 to 50ºC)
Resolution 720p
Infrared LED Lamps 12 LEDs (5mm)
Minimum Illumination Color: 0.1 lux (F2.0)
B&W, IR LED on: 0 lux
Enclosure Size Diameter : 3.74”(95 mm)
Height: 2.64” (67 mm)
Enclosure Material Solid aluminum alloy
Dome Impact-resistant polycarbonate, anti-glare,
scratch-resistant hardcoating, UV protected
Connector Cable Length 12” (30 cm)
Weight 0.52 lbs (0.24 kg)
Support
Service
If your HD1Q Series Dome Camera is to be returned to Seon Design for service, please call toll
free 1-877-630-7366, or 604-941-0880, and provide the model and/or serial number of your
unit. Ask for a Return Authorization (RA) number. An RA number allows the Service Technicians
to track your product when it comes in for service. Please display the RA number on the outside
of the package. ANY PRODUCT SENT TO SEON DESIGN WITHOUT AN RA NUMBER WILL BE
RETURNED.
Warranty
For full warranty information, go to www.seon.com/warranty.html.
Documentation
Copies of this guide can be found online at https://community.seon.com
Information in this guide is subject to change without notice.
B
C
D
1
2
A
B
A
C
D
3
4
5
File Last Saved Date: July-06-17 4:09:25 PM
File Name: HD1Q Install Images
6
TOLERANCES ARE:
REVISION
DIMENSIONS ARE IN MM
UNLESS OTHERWISE NOTED
NO DECIMAL PLACES
1 DECIMAL PLACE
2 DECIMAL PLACE
ANGLES
ARENA Tracking:
ENG:
DRAWN:
DATE
APPROVALS
SEON DESIGN INC.
111 - 3B Burbidge St.
Coquitlam, BC
Canada V3K 7B2
TEL: [phone]
FAX: [phone]
MANUFACTURING DESCRIPTION:
PART NUMBER:
SHEET
SIZE
A
1 of 1
SHEET:
THIRD ANGLE PROJECTION
COPYRIGHT SEON DESIGN INC., ALL RIGHTS RESERVED. THIS DOCUMENT MAY NOT BE DISCLOSED, OR REPRODUCED BY ANY MEANS WITHOUT THE WRITTEN CONSENT OF SEON DESIGN.
3
2
1
4
6
5
Shim Kit (part # 020-1041):
• 1 shim angle mount (part # 665-1017)
• 2 x No. 8 screws
(2” length, part # 600-1015)
• 1 x No. 8 screw
(1.25” length, part # 600-1016)
• 3 x rubber washers
(part # 610-1001)
• 1 Quick Install Guide
(part # 700-1094)
Installation Kit Contents
The HD1Q camera with IR designed for interior use only. This Guide replaces the HD1Q Dome
Camera Quick Install Guide (part # 700-1084) for installations requiring the angle mount shim.
Step 6: Replace Camera Dome
1. Fit the dome onto the base, ensuring the foam IR boot around the camera lens is rmly
pressed against the inside of the dome.
2. Use the security key to tighten the captive screws.

Step 1: Choose Camera Location
Note: Consider the desired eld of view, area of focus, and camera/shim assembly orientation.
Generally, the shallow side of the shim should point in the direction of the camera lens.
1. Determine the location for mounting the camera.
a. Choose a solid surface to minimize vibration
b. Choose a location away from access panels, hatches, or doors which may block the
camera view
c. Choose a location away from heat sources
d. Cameras are usually installed with the cabling running inside the wall panels.
2. Use the angle mount shim as a guide to mark the cable hole (7/8”) on the panel.
3. Use a step-bit to drill the cable hole.
Step 3: Connect Camera
to DVR
1. Position the shim against the camera base and pull the
camera cable through the center of the shim.
2. Connect the camera cable to the extension cable
through the panel cable hole.
Important: ensure the extension cable has a blue
band in front of the connectors, indicating it is AHD-
compatible.
3. Connect the extension cable’s 2x3 Micro-Fit connector
to the DVR.
Step 2: Remove Camera Dome
1. Using the security key supplied with the camera, loosen the captive screws on the housing.
2. Lift the housing o of the base.
3. Slide one of the longer
self-drilling mounting
screws (No. 8 x 2”)
through the camera
and the hole at a
thicker edge of the
shim, and attach it to
the vehicle panel.
4. Repeat step 3 with
the other 2” mounting
screw.
5. Slide the shorter
self-drilling mounting
screw (No. 8 x 1.25”)
through the camera
and the hole at the
thinnest edge of the
shim, and fully attach
the camera/shim
assembly.
Step 5: Aim Camera
1. With a monitor connected to the DVR, power up the system. The monitor should display the
multiple camera views once the DVR is powered up.
2. Double-click a camera to display it in full-screen mode.
3. Aim the camera by tilting and rotating as required.
Step 4: Install Camera and Shim Angle Mount
1. Slide a rubber washer over each of the mounting screws.
2. Use the alignment peg to position the camera base against the shim so the cable notch and
the mounting holes line up.
Step 4 (continued)
Note: Take care to ensure all
3 screws are perpendicular
to the camera base.