Server 86819 User manual

For purchasing this kit to transform your
topping warmer into a Signature Touch™
Squeeze Bottle Warmer. Drizzle and delight!
SERVE BETTER WITH DISTINCTIVE
DESSERTS
Thank You
BOTTLE SUPPORT
86811
SQUEEZE BOTTLES (3)
High-Density, 16 oz
86809
Bottle Support Kit
86819

Page 2
According to food and safety regulations, most
foods must be stored and/or served at certain
temperatures or they could become hazardous.
Check with local food and safety regulators for
specic guidelines.
Be aware of the product you are serving and the
temperature the product is required to maintain.
Server Products, Inc. cannot be responsible for the
serving of potentially hazardous product.
CAUTION:
Prevent serious burns and
bottle failure.
DO NOT EXCEED 125° F (52°C).
YES
Squeeze bottles are dishwasher safe.
CARE OF STAINLESS STEEL
•A mildly abrasive nylon or brass brush may
be used to remove any stubborn deposits.
•Fully rinsing and drying all parts can help
prevent corrosion. Elements and minerals in
tap water can accumulate on stainless steel
parts and create corrosion.
•Do not use abrasive, caustic or ammonia
based cleansers.
•Do not use products containing acids,
alkalines, chlorine, or salt. These agents can
corrode stainless steel.
•Do not use metal scrapers or cleaning pads
that could scratch surfaces.
SAFETY
CLEANING
WASH
all parts properly before use.
SANITIZE
all parts according to local sanitization
requirements. All parts in contact with food
must be sanitized.

Page 3
SET-UP
IMPORTANT: Unit must use water.
• Pour 4—6 cups (946-1420mL) of water
into basin.
• Do not overll.
FILL WATER VESSEL BASIN
1
FILL BOTTLES
3
INSERT BOTTLE SUPPORT
2
TIP: Check water levels
throughout the holding period
to ensure even heating.
Filtered water is recommended
to deter corrosion.
TIP: Simplify change-outs
with additional bottles.
Order item #86809.
into water vessel basin.
with desired product.
• Product being served must be inside
squeeze bottles.
INSERT BOTTLES
4
into bottle support openings.
REFER TO WARMER MANUAL
5
for complete instructions included with your
original FS & FSP warmer model.
Manuals are also available at:
www.Server-Products.com
CAUTION:
Prevent serious burns and
bottle failure.
DO NOT EXCEED 125° F (52°C).

Page 4 Manual #EM_01912_RevC 032222
TAKE-DOWN
PRESS SWITCH to the “OFF” position.
1
EMPTY WATER FROM
WATER VESSEL BASIN
after each use.
Carefully pour water down a drain.
5
DRY
thoroughly with a soft dry cloth.
6
REMOVE BOTTLES
3
REMOVE BOTTLE SUPPORT
4
UNPLUG CORD
2
CAUTION- HOT
Allow unit to cool or
take proper care with hot surfaces.
TIP: Remember to empty the water
each day rather than add—
This will greatly extend the life of
your warmer.
Proper drying after each use helps
maintain the stainless steel.
NEED HELP?
Please be prepared with your Model, P/N and
Series located on the lid or base of the unit.
Example:
Chat with us!
[email protected]
262.628.5600 | 800.558.8722
Server Products Inc.
3601 Pleasant Hill Road
Richfield, WI 53076 USA MODEL
XXXX
P/N
#####
SERIES
##X ##X
SERVER PRODUCTS
LIMITED WARRANTY
This Server product is backed by a two-year
limited warranty against defects in materials and
workmanship. See Server-Products.com for details.
GENERAL SERVICE,
REPAIR OR RETURNS
Before sending an item to Server Products, contact Customer Care to
request a Return Authorization Number. The RA Number ensures proper
processing and a prompt turnaround. Repaired units are typically shipped
out within 48 hours of receipt.
Merchandise returned for credit will incur a 20% restocking charge, must
be less than 90 days old, and in unused (new) condition. Electrical parts
(thermostats, heating elements, etc.) are not returnable.
Servicing Cord: Specic tools are required for safe and proper power
supply cord removal and installation. Repairs should be done by an OEM
representative or qualied technician using a cord meeting code H05
RN-F requirements.