SET SET-2110 Parts list manual

1 of 9
www.smart-e-tech.com
SET-2110
Technical Description
Issue 02 24/05/2022
TECHNICAL DESCRIPTION
SET-2110
16 Differential / 32 Single-ended Channel Fault Insertion Card
This document is a technical description of the SET-2110.
Note Before you begin, complete the software and hardware installation procedures
applicable to your application.
Note The guidelines in this document are specific to the SET-2110. The other components in
the system might not meet the same safety ratings. Refer to the documentation of each com-
ponent in the system to determine the safety and EMC ratings for the entire system.
MORE INFORMATION ON OUR WEBSITE:
www.smart-e-tech.de/slsc

2 of 9
www.smart-e-tech.com
SET-2110
Technical Description
Issue 02 24/05/2022
Safety Guidelines
Caution Do not operate the SET-2110 in a manner not specified in this document. Product
misuse can result in a hazard. You can compromise the safety protection built into the product
if the product is damaged in any way. If the product is damaged, return it for repair.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits for electromagnetic
compatibility (EMC). These requirements and limits provide reasonable protection against harmful
interference when the product is operated in the intended operational electromagnetic environment.
This product is intended for use in industrial locations. However, harmful interference may occur in
some installations, when the product is connected to a peripheral device or test object, or if the
product is used in residential or commercial areas. To minimize interference with radio and television
reception and prevent unacceptable performance degradation, install, and use this product in strict
accordance with the instructions in the product documentation.
Furthermore, any changes or modifications to the product not expressly approved by SET GmbH could
void your authority to operate it under your local regulatory rules.
Caution To ensure the specified EMC performance, operate this product only with shielded
cables and accessories.
Caution To ensure the specified EMC performance, the length of any cable attached to
connectors J1 and J2 must be no longer than 3 m (10 ft.)

3 of 9
www.smart-e-tech.com
SET-2110
Technical Description
Issue 02 24/05/2022
Description
The SET-2110 Fault Insertion Card is a large-scale, high density switching matrix. Each line of the 32
single-ended or 16 differential channels can be connected individually and flexibly to the high current
fault injection bus. For this, one of both fault bus signal pairs can be selected dynamically for every
channel. The SET-2110 Fault Insertion Card also provides the ability to generate short circuits between
a channels positive and negative signal. Unlike traditional routing matrix cards, the SET-2110 is designed
specifically for the challenges of signal routing in HIL systems. To maximize customizability, the SET-2110
features two plug-in module slots that can provide additional features, such as instrument connect.
Circuitry
Note Diagram only shows one channel.

4 of 9
www.smart-e-tech.com
SET-2110
Technical Description
Issue 02 24/05/2022
15
30
44 14
29
43 13
28
42 12
27
41 11
26
40 10
25
39 9
24
38 8
23
37 7
22
36 6
21
35 5
20
34 4
J1, J2 Pinout (Front)
J1 J2
Signal
Description
Px.y
Line y in Port x
NC
No connection
EN
Enable
REF
Reference
J1, J2 Connector Pin Assignments
15
30
44
14
29
43
13
28
42
12
27
41
11
26
40
10
25
39
9
24
38
8
23
37
7
22
36
6
21
35
5
20
34
4
19
33
3
18
32
2
17
31
1
16
P3.2+
P3.2-
P3.1+
P3.1-
P3.0+
P3.0-
EN3
EN2
P2.2+
P2.2-
P2.1+
P2.1-
P2.0+
P2.0-
NC
NC
P1.2+
P1.2-
P1.1+
P1.1-
P1.0+
P1.0-
EN1
EN0
P0.2+
P0.2-
P0.1+
P0.1-
P0.0+
P0.0-
P3.3+
P3.3-
REF3
REF2
P2.3+
P2.3-
NC
NC
P1.3+
P1.3-
REF1
REF0
P0.3+
P0.3-
15
30
44
14
29
43
13
28
42
12
27
41
11
26
40
10
25
39
9
24
38
8
23
37
7
22
36
6
21
35
5
20
34
4
19
33
3
18
32
2
17
31
1
16
P7.2+
P7.2-
P7.1+
P7.1-
P7.0+
P7.0-
EN7
EN6
P6.2+
P6.2-
P6.1+
P6.1-
P6.0+
P6.0-
NC
NC
P5.2+
P5.2-
P5.1+
P5.1-
P5.0+
P5.0-
EN5
EN4
P4.2+
P4.2-
P4.1+
P4.1-
P4.0+
P4.0-
P7.3+
P7.3-
REF7
REF6
P6.3+
P6.3-
NC
NC
P5.3+
P5.3-
REF5
REF4
P4.3+
P4.3-

5 of 9
www.smart-e-tech.com
SET-2110
Technical Description
Issue 02 24/05/2022
XJ2 Connector Pinout (Rear)

6 of 9
www.smart-e-tech.com
SET-2110
Technical Description
Issue 02 24/05/2022
Row
e
d
c
b
a
1
P0.1- / P4.1-
P0.1+ / P4.1+
NC
P0.0- / P4.0-
P0.0+ / P4.0+
2
P0.3- / P4.3-
P0.3+ / P4.3+
NC
P0.2- / P4.2-
P0.2+ / P4.2+
3
GND
GND
GND
GND
GND
4
P1.1- / P5.1-
P1.1+ / P5.1+
NC
P1.0- / P5.0-
P1.0+ / P5.0+
5
P1.3- / P5.3-
P1.3+ / P5.3+
NC
P1.2- / P5.2-
P1.2+ / P5.2+
6
GND
GND
GND
GND
GND
7
P2.1- / P6.1-
P2.1+ / P6.1+
NC
P2.0- / P6.0-
P2.0+ / P6.0+
8
P2.3- / P6.3-
P2.3+ / P6.3+
NC
P2.2- / P6.2-
P2.2+ / P6.2+
9
GND
GND
GND
GND
GND
10
P3.1- / P7.1-
P3.1+ / P7.1+
NC
P3.0- / P7.0-
P3.0+ / P7.0+
11
P3.3- / P7.3-
P3.3+ / P7.3+
NC
P3.2- / P7.2-
P3.2+ / P7.2+
12
NC
NC
NC
NC
NC
13
NC
NC
NC
NC
NC
14
NC
NC
NC
NC
NC
15
NC
NC
NC
NC
NC
16
NC
NC
NC
NC
NC
17
GND
GND
GND
GND
GND
18
NC
NC
NC
NC
NC
19
NC
NC
NC
NC
NC
20
GND
GND
GND
GND
GND
21
NC
NC
NC
NC
NC
22
NC
NC
NC
NC
NC
23
GND
GND
GND
GND
GND
24
NC
NC
NC
NC
NC
25
NC
NC
NC
NC
NC
XJ2 Connector Pin Assignments
Signal
Description
Px.y
Line y in Port x
GND
Ground connection
NC
No connection
XJ2 Connector Signal Descriptions

7 of 9
www.smart-e-tech.com
SET-2110
Technical Description
Issue 02 24/05/2022
XJ3 Connector Pinout (Rear)
Pins
Signal
Slot1/Slot2
H
V1+
Instrument 0+
G
V1-
Instrument 0-
F
V2+
Instrument 1+
E
V2-
Instrument 1-
D
V3+
Fault A
C
V3-
Fault B
B
V4+
Fault C
A
V4-
Fault D
XJ3 Connector Pin Assignments
H
G
F
E
D
C
B
A

8 of 9
www.smart-e-tech.com
SET-2110
Technical Description
Issue 02 24/05/2022
LED Behavior
LED Name
LED Behavior
Definition of Behavior
PWR
Off
No power present on the board
Solid green
Power good state
RDY
Off
Module card is unpowered or reset active
Solid green
Card is recognized by chassis and ready to communicate
Amber
Chassis is communicating
Error Handling
LED Name
LED Behavior
Actions
PWR
Off
-Check power supply of chassis
-Check external power supply if used
PWR
Blinking Red
-Check plugin module on board
-Check fuse on board
Hardware Specifications
Absolute Maximum Ratings
Property
Condition
Value
Comment
Max. Input Voltage
Any Pin
60 V DC
Min. Input Voltage
Any Pin
-60 V DC
Max. Switching Power
DC, Resistive load
60 W
Max. Current Rating
1.5 A

9 of 9
www.smart-e-tech.com
SET-2110
Technical Description
Issue 02 24/05/2022
Technical Data
Property
Condition
Value
Comment
Update Time
10 ms
SLSC Commit CMD
duration
Max Initial Contact
Resistance
J1 -> XJ2
J2 -> XJ2
J1 -> J2
500 mΩ
Expected Electrical
Lifetime
1 A, 30 VDC resistive
10ˆ5 operations
1.5 A, 30 VDC resistive
10^4 operations
Bandwidth
-3 dB
50 Ω Termination
≤ 20 MHz
Physicals Characteristics
Property
Condition
Value
Comment
Module Dimensions
Excluding ejector
144.32 mm x 30.48 mm x
302 mm (H x W x D)
Standard SLSC card size
Front Panel Connector
2x female DB -44 high-
density D-Sub with 4-40
UNC screw lock
For mating connectors
and cables, see below
RTI Connector
2 mm hard metric per
IEC 61076-101
Any RTI marked
Environmental
Property
Condition
Value
Comment
Operating Humidity
Relative, non-
condensing
10%-90%
Storage Humidity
Relative, non-
condensing
5%-95%
Operating
Temperature
Forced-air cooling from
chassis
0°C to 40°C
Storage Temperature
-40°C to 85°C
Maximum Altitude
2000 m