H3C 1000BASE-X-SFP User manual

Manual version: 6PW103-20180115 BOM: 3123A1AJ
i
24-port 1000BASE-X-SFP + 4-port 10GBASE-R-SFP+
optical Ethernet interface card—LSQM2GP24TSSA0
1 Card identifier
The card identifier LSQM2GP24TSSA0 is in the upper right corner of the front panel.
2 Specifications
IMPORTANT:
Before installing the card, you must remove the protection cover from the card to ensure correct
installation.
Table 1 Card specifications
Item Specifications
Card size (H × W × D) 40 × 399 × 355 mm (1.57 × 15.71 × 13.98 in)
SDRAM (DDR3) 1GB
Power consumption 25 W to 49 W
Ports •24 x 1000BASE-X-SFP fiber ports
•4 x 10GBASE-R-SFP+ fiber ports
Connector type LC
Port rate •1000 Mbps
•10 Gbps
Transmission medium and
max transmission distance
•1000BASE-X-SFP fiber port: see Table 2
•10GBASE-R-SFP+ fiber port: see Table 2 , Table 3and Table 4
Applicable hardware platforms •All S7500E models
•All S7500X models
System software version Release 7178 and Later
Table 2 describes the SFP transceiver modules available for the card.
Table 2 SFP transceiver module specifications
Module Central
wavelength Connector type Cable specifications
Maximum
transmission
distance
SFP-GE-SX-MM850-A 850 nm LC 50/125 µm multi-mode
optical fiber 550 m (0.34 miles)
850 nm LC 62.5/125 µm
multi-mode optical fiber 275 m (0.17 miles)

Manual version: 6PW103-20180115 BOM: 3123A1AJ
ii
Module Central
wavelength Connector type Cable specifications
Maximum
transmission
distance
SFP-GE-SX-MM850-D 850 nm LC 50/125 µm multi-mode
optical fiber 550 m (0.34 miles)
850 nm LC 62.5/125 µm
multi-mode optical fiber 275 m (0.17 miles)
SFP-GE-LX-SM1310-A
1310 nm LC 9/125 µm single-mode
optical fiber 10 km (6.21 miles)
1310 nm LC 50/125 µm multi-mode
optical fiber 550 m (1804.46 ft)
1310 nm LC 62.5/125 µm
multi-mode optical fiber 550 m (1804.46 ft)
SFP-GE-LX-SM1310-D
1310 nm LC 9/125 µm single-mode
optical fiber 10 km (6.21 miles)
1310 nm LC 50/125 µm multi-mode
optical fiber 550 m (1804.46 ft)
1310 nm LC 62.5/125 µm
multi-mode optical fiber 550 m (1804.46 ft)
SFP-GE-LH40-SM1310 1310 nm LC 9/125 µm single-mode
optical fiber 40 km (24.86 miles)
SFP-GE-LH40-SM1310-D 1310nm LC 9/125 µm single-mode
optical fiber 40 km (24.86 miles)
SFP-GE-LH40-SM1550 1550 nm LC 9/125 µm single-mode
optical fiber 40 km (24.86 miles)
SFP-GE-LH80-SM1550 1550 nm LC 9/125 µm single-mode
optical fiber 70 km (43.50 miles)
SFP-GE-LH80-SM1550-D 1550nm LC 9/125 µm single-mode
optical fiber 70 km (43.50 miles)
SFP-GE-LH100-SM1550 1550 nm LC 9/125 µm single-mode
optical fiber 100 km (62.14 miles)
SFP-GE-LX-SM1310-BIDI RX: 1490 nm
TX: 1310 nm LC 9/125 µm single-mode
optical fiber 10 km (6.21 miles)
SFP-GE-LX-SM1490-BIDI RX: 1310 nm
TX: 1490 nm LC 9/125 µm single-mode
optical fiber 10 km (6.21 miles)
SFP-GE-T N/A RJ-45
Category-5 twisted pair
cable 100 m (0.06 miles)
SFP-GE-T-D N/A RJ-45
Category-5 twisted pair
cable 100 m (0.06 miles)
SFP-FE-SX-MM1310-A 1310 nm LC
50/125 µm multi-mode
optical fiber 2 km (1.24 miles)
62.5/125 µm
multi-mode optical fiber 275 m (0.17 miles)
SFP-FE-LX-SM1310-A 1310 nm LC 9/125 µm single-mode
optical fiber 15 km (9.32 miles)
SFP-FE-LX-SM1310-D 1310 nm LC 9/125 µm single-mode
optical fiber 15 km (9.32 miles)

Manual version: 6PW103-20180115 BOM: 3123A1AJ
iii
NOTE:
•BIDI modules use different central wavelengths in transmit and receive directions, in order to
implement bidirectional transmission of optical signals over the same fiber.
•BIDI modules must be used in pairs. For example, if an SFP-GE-LX-SM1310-BIDI is used at one
end, an SFP-GE-LX-SM1490-BIDI must be used at the other end.
•The 10GBASE-R-SFP+ port does not support the following SFP transceiver modules:
SFP-GE-T, and SFP-GE-T-D.
Table 3 describes the SFP+ transceiver modules available for the SFP+ ports on the card.
Table 3 SFP+ transceiver module specifications
Module Central
wavelength Connector type Cable specifications
Maximum
transmission
distance
SFP-XG-SX-MM850-A 850 nm LC 50/125 µm multi-mode
optical fiber 300 m (984.25 ft)
850 nm LC 62.5/125 µm
multi-mode optical fiber 33 m (108.27 ft)
SFP-XG-SX-MM850-D 850 nm LC 50/125 µm multi-mode
optical fiber 300 m (984.25 ft)
850 nm LC 62.5/125 µm
multi-mode optical fiber 33 m (108.27 ft)
SFP-XG-SX-MM850-E 850 nm LC 50/125 µm multi-mode
optical fiber 300 m (984.25 ft)
850 nm LC 62.5/125 µm
multi-mode optical fiber 33 m (108.27 ft)
SFP-XG-SX-MM850-F1 850 nm LC 50/125 µm multi-mode
optical fiber 300 m (984.25 ft)
850 nm LC 62.5/125 µm
multi-mode optical fiber 33 m (108.27 ft)
SFP-XG-LX-SM1310 1310 nm LC 9/125 µm single-mode
optical fiber 10 km (6.21 miles)
SFP-XG-LX-SM1310-D 1310 nm LC 9/125 µm single-mode
optical fiber 10 km (6.21 miles)
SFP-XG-LX-SM1310-E 1310 nm LC 9/125 µm single-mode
optical fiber 10 km (6.21 miles)
SFP-XG-LH40-SM1550 1550nm LC 9/125 µm single-mode
optical fiber 40 km (24.86 miles)
SFP-XG-LH40-SM1550-D 1550nm LC 9/125 µm single-mode
optical fiber 40 km (24.86 miles)
SFP-XG-LH80-SM1550 1550nm LC 9/125 µm single-mode
optical fiber 80 km (49.71 miles)
SFP-XG-LH80-SM1550-D 1550nm LC 9/125 µm single-mode
optical fiber 80 km (49.71 miles)

Manual version: 6PW103-20180115 BOM: 3123A1AJ
iv
Table 4 describes the SFP+ DAC cables available for the SFP+ ports on the card.
Table 4 SFP+ DAC cable specifications
SFP+ DAC cable Cable length Data rate Cable type Remark
LSWM1STK 0.65 m (2.13 ft)
10.31 Gbps SFP+ cable Use for connecting
SFP+ ports
LSWM2STK 1.2 m (3.94 ft)
LSWM3STK 3 m (9.84 ft)
3 Related documentation
For module installation, see H3C S7500E Switch Series Installation Guide and H3C S7500X Switch
Series Installation Guide.
For software upgrade, see the release notes for the device.
Copyright © 2015-2018 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.