Seville Classics airLIFT OFF65871 User manual

airLIFT® Height Adjustable Electric Single Motor Desk
with Glass Top + Dual Charging Ports (USB-A, USB-C)
+Safety Lock Feature
Models: OFF65871 / OFF65873 / OFF65846B
Thank you for choosing Seville Classics! We hope that you enjoy your new sit-to-stand
desk. Please read through this user guide for parts list, instructions, frequently asked
questions and contact information.
V020822

Get help with assembly and report damaged or missing parts.
Email: [email protected]
Telephone: [phone]
Hours: 8:30 AM - 4:30 PM (PST) 1
Welcome and Congrats on your new Desk!
Congratulations on your new airLIFT® electric desk, now you can enjoy all the benefits of a truely
smart and stylish workstation.
We at Seville Classics® are thrilled that you’ve chosen to go airLIFT®! Our desks are some of the
easiest to use, most versatile and sophisticated electronic desks on the market. With this, you can
stay active throughout the day without sacrificing productivity.
Choosing a height-adjustable desk is not just a convenient upgrade—it’s a healthy one! Too much
sedentary behavior can present a real health risk, even for people who are already healthy. Simply
getting up throughout the day and moving is a great way to fight the consequences of too much
sitting.
airLIFT® is here to help.
Please read through this manual for more information regarding your airLIFT® Height Adjustable
Electric Single Motor Desk with Glass Top + Dual Charging Ports (USB-A, USB-C) + Safety Lock
Feature
Thank you for choosing Seville Classics®!
We hope you will enjoy this desk for many years to come.
Post Setup Quick Start Instructions
Once your desk has been put together or when reset (initialization) is necessary:
1). Press & Hold the DOWN ARROW until the desk reaches the lowest position and/or stops moving.
2). Release your finger from the DOWN ARROW momentarily and then Press & Hold again until:
(a). Screen is flashing “RSt”.
(b). Desk rebounds.
(c). You will hear a “DING” sound.
3). Release your finger and this completes the initialization/reset procedure.

3
4
5
6
6
7
8
9
10
Table of Contents
SAFETY INSTRUCTIONS …………………………………………………………………………….
COMPONENT DIAGRAM .....................................................…………………………..
PARTS LIST ................................…………………………………………………………………..
ASSEMBLY INSTRUCTIONS ................................................…………………………….
Unpack .................……………………………………………………………………………..
Install Brackets ...........................................…………………………………………..
Install Legs ...............................................…………………………………………….
Connect Motor ...........................................………………………………………….
Final Steps ......................……………………………………………………………….…..
INITIALIZATION & USE INSTRUCTIONS.................……………………………………….
11
TROUBLESHOOTING………………………………………………………………………………….
13
WARRANTY SERVICE INFORMATION .............................……………………………….
14
ADVANCED FUNCTION SETTINGS............................……………………………………….
12
Get help with assembly and report damaged or missing parts.
E mail: [email protected]
Telep h o n e: 1 [phone]
Hours: 8:30 AM - 4:30 PM (PST) 2
CUSTOMER SERVICE INFORMATION .............................……………………………….
15

Safety Instructions
FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND
OPERATING INSTRUCTIONS AND WARNINGS REGARDING THE USE OF THIS
PRODUCT MAY RESULT IN SERIOUS BODILY INJURY
The desk MUST be INITIALIZED before first use.
Read the INITIALIZATION chapter prior to operation.
•Read and understand this manual before attempting to install or
•Assure that everyone who uses this product is informed of the contents of this manual. This
is the responsibility of the Purchaser.
•Not intended for use by young children or for those persons who require supervision.
•Do not open any of the components – legs, control box, or LED Control Panel. There is a risk
of electric shock.
•Assemble desk on a flat and level surface.
Use & Liability
Safe use of this product is possible only when the operating instructions are read completely
and the instructions contained are strictly observed. Persons who do not have the necessary
experience or knowledge of this product must not use the product. Persons with reduced
physical or mental abilities should not use this product, unless they are under supervision or
they have been thoroughly instructed in the use of the apparatus by a person who is
responsible for the safety of these persons. Children should be closely supervised to ensure that
they do not play with this product.
Before You Begin
Layout all components and hardware. Visually examine and make sure components are free of
damage. If there is visual damage to any component, it must not be installed.
Two people are needed to turn or move the desk and some of it’s components. When moving or
turning the assembled desk, grab the legs, not the desk top.
Make sure to assemble on a soft and non-abrasive surface to avoid scratches.
Check all connections and cables. Make sure control box is connected to a power outlet.
If the control box makes unusual noises or emits an odor, switch power off immediately.
Get help with assembly and report damaged or missing parts.
E mail: [email protected]
Telep h o n e: 1 [phone]
Hours: 8:30 AM - 4:30 PM (PST) 3

Foot
Drawer
LED Control
Panel
Legs/Beam
Frame with
Tempered Glass
Top
Get help with assembly and report damaged or missing parts.
E mail: [email protected]
Telep h o n e: 1 [phone]
Hours: 8:30 AM - 4:30 PM (PST) 4
Motor
Bracket
Power
Supply
Quick Setup Diagram
Setup should take about 15 minutes to complete. All required tools
are included. Keep the frame with tempered glass top in the box
during assembly to protect it from scratches.

Parts List
Tools & Hardware List
Please make sure you have all the parts on this list.
Leave the Top in the box during assembly
If you’re missing parts, contact us for replacements at [phone] or
send an email to [e-mail]
A. Frame with
Tempered Glass Top
(Drawer, LED Control
Panel, and Power
Supply attached) (1)
B. Legs/Beam
(Motor attached) (1)
C. Brackets (2)
D. Feet (2)
E. M6 x 12 Screws (8)
F. M8 x 16 Screws (8)
G. 4 mm Hex Key
H. 5 mm Hex Key
5

Examine the location where you'll be
using the desk. Make sure there is a grounded
outlet or power strip nearby.
Assembly Instructions: Unpack
Remove the box lid and remove inner box containing parts.
Leave the frame with tempered glass top in the TOP
section of the box.
Layout all components and hardware. Examine each and make sure components
are without damage.
Frame with Tempered Glass Top
Pre-assembled Legs/
Beam (x1)
Feet (x2)
All Parts needed to assemble seen in
above figure. Essentially just 4 simple
steps of connecting 6 pieces in place.
Note: Outlet
voltage should be
110-120V
G et h elp w it h assem b l y a nd report d ama g e d or missi ng parts.
E mail: [email protected]
Telep h o n e: 1 [phone]
H ours: 8:30 AM - 4:30 PM (PST) 6

You should now have an assembled unit as pictured below.
Get help with assembly and report damaged or missing parts.
E mail: [email protected]
Telep h o n e: 1 [phone]
Hours: 8:30 AM - 4:30 PM (PST) 7
Assembly Instructions: Attach Support Brackets to
Legs/Beam using the M6 x 12 screws.
STEP 1. Fit BRACKET (C) into the left LEG/BEAM (B) using 2 M6 x 12 SCREWS (E) for this
you will need the 4 mm HEX KEY (G). Repeat this process for the right side.

Attached with 2 M6 x 12 SCREWS (E) using the 4 mm HEX KEY
(G) on each side as displayed in the figure below.
Motor side
goes behind LED
Control Panel
Get help with assembly and report damaged or missing parts.
E mail: [email protected]
Telep h o n e: 1 [phone]
Hours: 8:30 AM - 4:30 PM (PST) 8
Assembly Instructions: Frame with Tempered
Glass Top to Legs/Beam
STEP 2. Align the FRAME WITH TEMPERED GLASS TOP (A) to the FRONT, the
LED Control Panel should be facing you. Center the LEGS/BEAM (B) to the
frame with MOTOR SIDE TO THE LEFT, as displayed in the below figure.

Assembly Instructions: Connect Motor Cable to
LED Control Panel
STEP 3. Plug in the Motor Cable from leg beam to LED Control Panel as
displayed in below figure.
Get help with assembly and report damaged or missing parts.
E mail: [email protected]
Telep h o n e: 1 [phone]
Hours: 8:30 AM - 4:30 PM (PST) 9
Motor
Cable
LED
Control
Panel

Lift with 2 people
Assembly Instructions: Final Steps
Tip! Take time to make sure all screws have been tightened.
STEP 5. With the assistance of another person, lift and tilt the table onto its feet.
Remove tape
Weight Capacity: 176 lbs. (evenly distributed)
Weight Capacity of Drawer: 11 lbs.
Get help with assembly and report damaged or missing parts.
E mail: [email protected]
Telep h o n e: 1 [phone]
Hours: 8:30 AM - 4:30 PM (PST) 10
TIP: Adjust the leveling
feet by rotating in and out as
necessary to ensure the desk
stands level and is not tilting.
STEP 4. Attach FEET (D) to LEGS/BEAM (B) using the M8 x 16 SCREWS
(F) with the 5 mm HEX KEY (H) tool as displayed in the below figure.

Use Instructions
DESK MUST BE INITIALIZED BEFORE FIRST USE
Up Arrow Down Arrow
Save Memory USB Charging Port:
Type A, Type C
Initialize & Reset
Once your desk has been put together or when reset
(initialization) is necessary:
1). Press & Hold the Down Arrow until the
desk reaches the lowest position and/or stops moving.
2). Release your finger from the Down Arrow
momentarily and then Press and Hold again until:
(a). Screen is flashing “RSt”.
(b). Desk rebounds.
(c). You will hear a “DING” sound.
3). Release your finger and this completes the
initialization/reset procedure.
Adjust Height
Press and hold the Up Arrow to lift.
Press and hold the Down Arrow button to lower.
Save Height
To save the desired height, lightly tap the “M” button
on the LED Control Panel, and an “S-“ will appear. Now
tap on any one of the 3 Memory Buttons to
successfully save and store the desired height.
Note, If a flashing “S-1” appears on the LED Control
Panel, this signifies that the “M” button was pressed for
too long. Wait for the system to reset itself, should take
5 seconds, and then start the above process over.
Recall Height
Lightly tap the desired number (1, 2, or 3), the
desk moves to memory height automatically.
12
Get help with assembly and report damaged or missing parts.
E mail: [email protected]
Telep h o n e: 1 [phone]
Hours: 8:30 AM - 4:30 PM (PST) 11
Memory Display

Limited Height Setting
Control overall height limits of the desk to prevent the desk
from going beyond a desired height level. Press and hold
both the Up Arrow + Down Arrow for 5 seconds until you
hear a ding sound, limited height setting success.
Cancel Limited Height Setting
Run to the limited height, press and hold Up Arrow + Down
Arrow again for 5 seconds, when you hear the ding sound,
limited height canceled.
Advanced Function Settings
Safety Lock
Lightly tap M button and the Up Arrow to lock the desk
in place; press the M button and the Down Arrow to unlock.
USB-A Port
USB-C Fast Charge Port
Use Only USB-A
Cable (left image)
for USB-A Port on
Desk.
Use USB-C Cable
(Left Image) for
USB-C Port on
Desk
USB Usage Instructions
Get help with assembly and report damaged or missing parts.
E mail: [email protected]
Telep h o n e: 1 [phone]
Hours: 8:30 AM - 4:30 PM (PST) 12

Troubleshooting
Error Codes
Code Acon
- - - Reset the desk.
Problem Acon
Desk does not go up or down and the
LED control panel does not illuminate
when any button is pressed.
Check all connections. Make sure power cord is plugged into the control box
and a power outlet. Press any button on the
LED control panel and make sure it illuminates. Reset the desk.
Desk does not go up or down and the LED
Control Panel shows "- - -" The desk has an initialization fault and must be reset.
Legs do not go up evenly. Unplug the power cord and re-plug after 10 seconds.
Reset the desk.
Desk wobbles excessively. It is normal that desk moves slightly at standing height when in use. Retighten
all screws and bolts, and adjust leveling feet to make sure table stands level.
The desk motor is overheated. Stop using the desk for 20 minutes and
let it to cool down.
Desk legs are noisy. It is normal that desk makes noise when the leg levels move past each
other.
E01, E06, E07 Check to ensure all cables are connected.
E02, E08 Make sure desk is adjusted evenly and reset system.
E04 Unplug the LED Control Panel and plug it in once again.
E05 Ensure that there is nothing obstructing the desk from moving.
E11, E13 Check the motor cable.
E12 Contact customer service.
E14 - E16 Check all cables and reset, if issue persists, contact customer service.
E17 Check motor cable and reset the desk.
E18 Remove some weight from the tempered glass desktop until error clears.
Get help with assembly and report damaged or missing parts.
E mail: [email protected]
Telep h o n e: 1 [phone]
Hours: 8:30 AM - 4:30 PM (PST) 13
Problem
HOT
Initialization Fault
Power Fault
Desktop Sloping
LED Control Panel Fault
Anti-Collision Activated
Motor Cable Fault
LED Control Panel Fault
Motor Cable Fault
Motor Fault
Overload
Motor Overheated
LOC Locked To unlock, press "M' button and "Down Arrow" button at the same time.

14
Warranty Information
7-Year Non-Electronic Component Warranty
Seville Classics, Inc. warrants to the original retail purchaser that if this product proves to be defective in
material or workmanship, we will replace the affected non-electronic part(s) for a period of seven
years on Seville Classics airLIFT® Electric Height Adjustable Standing Desks from the date of
original purchase.
2-Year Electronic Component Warranty
Seville Classics, Inc. warrants to the original retail purchaser that if this product proves to be defective in
material or workmanship we will replace the affected electronic part(s) for a period of two years on
Seville Classics airLIFT® Electric Height-Adjustable Standing Desks from the date of original purchase.
Except for the express warranty set forth above and except to the extent prohibited by applicable law,
Seville Classics grants no other express or implied warranties with respect to the product, its fitness for
any purpose, its quality, or its merchantability. The liability of Seville Classics under the warranty shall be
limited to the amount paid by the customer for the product. Seville Classics shall not be liable for any
loss of use of the product, or other incidental or consequential costs, expenses or damages incurred by
the customer or other user.
This warranty covers only the airLIFT® Height Adjustable Standing Desk sold in the United States of
America and Canada. Some states do not allow the exclusion or limitations of implied warranties or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights that vary from state to state.
During the applicable warranty period, Seville Classics, at its option, will either refund the original pur-
chase price or replace the affected part(s) with comparable part(s) when the affected part(s) are
returned, postage prepaid, to the address below:
Seville Classics Inc.
19401 South Harborgate Way
Torrance, CA 90501 – 1322 U.S.A.
To obtain warranty coverage, you must:
Have an original copy of the purchase receipt or invoice from any authorized retailer.
For warranty questions please contact customer support.
Email: [email protected]
Telephone: [phone]
Hours: 8:30 AM - 4:30 PM (PST)

156
V020822
Customer Service Information
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced Radio/TV technician for help
Get help with assembly and report damaged or missing parts.
Phone: [phone]
Email: [email protected]
Homepage: www.SevilleClassics.com
Hours: 8:30 AM - 4:30 PM (PST)