Seville Classics 20294 User manual

SC200820
ASSEMBLY INSTRUCTIONS
UltraHD® 4-Door Locker Cabinet (Model No. 20294)
15 in. W X 18 in. D X 72 in. H
(38.1 cm x 45.7 cm x 1.83 m)
Reference page 11 for special care
and maintenance of stainless steel

1

(#1-A) Left Panel
(#2-A) Right Panel
2

PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our
customer service department. (Please refer to page 12.)
(#1-A1) Left Side - Upper Panel x 1 PC
(#2-A1) Right Side - Upper Panel x 1 PC
(#3) Top Panel x 1 PC
(#4) Bottom Panel x 1 PC
(#5) Middle Shelf x 2 PCS
(#7) Middle Layer Panel x 1 PC
(#2-A2) Right Side - Bottom Panel x 1 PC
(#1-A2) Left Side - Bottom Panel x 1 PC
3

(#16) Corner Protection - B x 2 PCS
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our
customer service department. (Please refer to page 12.)
(#11) Lock Plate x 4 PCS
(#15) Corner Protection - A x 2 PCS
(#8) Upper Back Panel x 1 PC
(#10) Bottom Back Panel x 1 PC
(#13) Middle Shelf Bracket x 4 PCS
(#2) Door Panel x 4 PCS
(#12) Middle Panel Bracket x 2 PCS
4

PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our
customer service department. (Please refer to page 12.)
(#25) Wrench x 1 PC
(#22) Key x 8 PCS
(#23) Magnet x 8 PCS
(#17) Middle Corner Protection x 2 PCS
(#6) Leveling Feet x 4 PCS
(#21) Screwdriver x 1 PC
(#41) Screw F (M4 x 8L) x 91 PCS
(#54) Screw N (M4 x 10L) x 28 PCS
5

(#60) Mounting Strap x 2 PCS
(#62) Name Card x 4 PCS
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our
customer service department. (Please refer to page 12.)
(#42) Screw G (M4 x 30L) x 12 PCS
(#61) Screw O (M4 x 12L) x 2 PCS
(#55-A) Wall Anchor x 2 PCS
(#55) Screw M (M6 x 50L) x 2 PCS
(#27) WASHER (M4) x 2 PCS
(#27-B) WASHER (M8)x 2 PCS
M8X20 pcs
6

TIP:
WARNING:
Step 1: Install Left Side Panel (#1-A)
Note:
Step 2: Install Right Side Panel (#2-A)
Note:
Step 3: Install Top Panel (#3) to Left Side Panel (#1-A)
and Right Side Panel (#2-A)
Note:
UltraHD® 4-Door Locker Cabinet (Model No. 20294)
*NOTE: We recommend using TWO people to assemble the cabinet.
Some parts may have sharp edges. To avoid injury,
wearing gloves is recommended during assembly.
A magnetic screwdriver is included for your
convenience. If using a power screwdriver,
keep toruqe setting on LOW during assembly.
Place the Left Side Upper Panel (#1-A1) and Left
Side Bottom Panel (#1-A2) together. Line up screw
holes, and use 3 pcs of Screw G (#42) to tighten
from the side.
Repeat Step 1. Place Right Side Upper Panel (#2-A1),
Right Side Bottom Panel (#2-A2) together. Line up
screw holes, and use 3 pcs of Screw G (#42) to
tighten from the side.
Before tightening screws, make sure the corners of
the Top Panel (#3) are completely flush.
Before tightening screws, make sure the corners
and the face of the Left Side Panel (#1-A) are
completely flush.
Before tightening screws, make sure the corners
and the face of the Right Side Panel (#2-A) are
completely flush.
Attach Top Panel (#3) to Left Side Panel (#1-A) and
Right Side Panel (#2-A). Make sure the front of the
unit faces downward. Line up screw holes, and use
6 pcs Screw F (#41) to tighten.
BOTTOM
FRONT
BACK
TOP
#42
#1-A1
#1-A2
#2-A
#41
#3
#1-A
#42
#2-A1
#2-A2
7

Step 4: Install Bottom Panel (#4) to Left Side Panel (#1-A)
and Right Side Panel (#2-A)
Note:
Step 5: Install Middle Layer Panel (#7)
Step 6:
1). Attach Bottom Back Panel (#10) onto both
Bottom of Left and Right Side Panels
(#1-A2 and #2-A2) and Bottom Panel (#4).
2) Attach the Upper Back Panel (#8) above the
Bottom Back Panel (#10) the same way. Place the
groove of the Upper Back Panel (#8) onto the top
edge of the Bottom Back Panel (#10).
3) Line up all the screw holes, use 27 pcs (#41)
Screw F to tighten the Back Panels.
Install Upper and Bottom Back Panels (#8, and #10)
UltraHD® 4-Door Locker Cabinet (Model No. 20294)
*NOTE: We recommend using TWO people to assemble the cabinet.
Attach Bottom Panel (#4) to Left Side Panel (#1-A)
and Right Side Panel (#2-A). Make sure the front of
the unit faces downward. Line up screw holes, and
use 6 pcs Screw G (#42) to tighten.
Before tightening screws, make sure the corners of
the Bottom Panel (#4) are completely flush.
1. Attach the Middle Layer Panel (#7) as the left
diagram shows. Use 8 pcs of Screw F (#41) to fasten
the Middle Layer Panel to the Left and Right Panels
(#1 and #2).
2. Remove the middle Screw G (#42) which attaches
the upper and bottom side panels on Step 1 & 2.
Attach the Middle Layer Panel Bracket (#12) to the
center of the Middle Layer Panel (#7) and install back
Screw G (#42) and install Screw F (#41).
1.
2.
TOP FRONT
TOP
TOP
FRONT
FRONT
#42
#4
#2-A
#1-A
#3
#41
#7
#7
#12
#42
#41
#41 #8
#10
8

Step 8: Install Middle Shelf (#5)
Step 9: Install Corner Protections (#15, #16 and #17)
UltraHD® 4-Door Locker Cabinet (Model No. 20294)
*NOTE: We recommend using TWO people to assemble the cabinet.
1). Attach Corner Protection A, B (#15, #16) onto
top and bottom of the cabinet. Use 20 pcs (#54)
Screw N to tighten.
2). Attach (#17-1) Middle Corner Protection to
the middle of (#1-A) Left Side Panel and (#2-A)
Right Side Panel. Use 8 pcs (#54) Screw N to
tighten.
Insert a Middle Shelf (#5) into the slots on the
Side Panels. Use 6 pcs Screw F (#41) to fasten the
Middle Shelf Bracket (#13) to the front of the side
panels.
Repeat Step 8 to assemble another Middle Shelf.
TOP
BACK
TOP
Front
#6
9
www.SevilleClassics.com. (Model #: WEB128)
See page 11 for installation instructions.
Note:
Step 7: Install Leveling Feet (#6).
Install Leveling Feet (#6) into the largest corn er
holes of the Bottom Panel (#4). Use Wrench (#25 )
to tighten.
Wheels are not included with this unit, however
there are 4 screw holes built into Bottom Panel
(#4) for installation. Wheels can be purchased at

Step 10:
Step 11: Install Magnet (#23)
Step 12: Install Door (#2)
NOTE:
The screw holes on the door hinge have
tolerance, enabling the door to be adjusted and
centered in the door frame. Place top, middle
and bottom screws first. Don't tighten screws
completely - this may save time by avoiding
having to make slight adjustments for leveling
door panels later.
UltraHD® 4-Door Locker Cabinet (Model No. 20294)
*NOTE: We recommend using TWO people to assemble the cabinet.
Install Lock Plate (#11)
Attach the Lock Plate (#11) on the Left Panel
(1-A). Use 8 pcs Screw F (#41) to tighten.
Place Magnet (#23) onto the top and bottom of
each panel. The black plate should be facing the
front. Use total 16 pcs Screw F (#41) to tighten
the magnets.
1). Attach Door (#2) to Right Side Panel (#2-A),
use 3 pcs Screw F (#41) to tighten.
Repeat this step to assemble the rest of the
doors.
10

UltraHD® Stainless Steel Care Instructions
• Lightly wipe with warm water and clean microfiber cloth
• Always wipe in the direction of the surface grain (NEVER ACROSS)
• Wipe away excess water with dry clean cloth
*NOTE: We recommend using TWO people to assemble the cabinet.
UltraHD® 4-Door Locker Cabinet (Model No. 20294)
Install Mounting Strap (#60)
A. Remove 1 pc Screw F (#41) from the back panel.
B. Attach the Mounting Strap (#60) to the back panel as
the left photo shows using Screw O (#61) and Washer
(#27).
C. Drill a hole in the wall with a 5/16" drill bit. Insert the
Wall Anchor (#55-A) into the hole.
Repeat steps A through D to install the other
mounting strap.
Warning: To prevent possible tipping, it is suggested that the
Mounting Straps be installed. For safety, secure the mounting
straps to wood studs whenever possible.
The stainless steel is protected with UltraGuard® fingerprint resistant finish.
DO NOT use traditional stainless-steel cleaners. To safely manage unwanted fingerprints and
prevent new stains, perform the following steps once monthly:
11
D. Attach the other end of the Mounting Strap (#60) to
the wall using Screw M (#55) and Washer (#27-B).
Installing Additional Wheels (WEB128)*
**Sold separately on SevilleClassics.com. Requires 2 pairs.
Installing Wheels
Step 1: Follow the previous instructions to Step 7.
DO NOT install Leveling Feet (#6).
Step 2: Install 2 pairs of wheels (WEB128) to the
bottom of the cabinet.
Use screws included with wheels to fasten.
Step 13:
WEB128

Seville Classics, Inc.
19401 Harborgate Way Torrance, CA 90501 USA
Telephone: [phone] within USA
Fax: [phone]
Hours: 9:00am - 4:30pm (Pacific Standard Time)
E-mail: [e-mail]
Website & Online Store: www.sevilleclassics.com
UltraHD® Tall Storage Cabinet UltraHD® Mega Storage Cabinet
Model No. 16236 (Granite) Model No. 16238 (Granite)
Model No. 20143 (Graphite)
Model No. 20148 (Graphite)
Model No. 20153 (Red) Model No. 20158 (Red)
Model No. 20133 (White)
CONTACT INFORMATION
If you are missing any parts, have any questions, or need additional assistance in assembly, please contact our
bilingual (English and Spanish) customer service department at:
***Please visit our website or call and inquire about our additional UltraHD Line***
UltraHD® Line
12

UltraHD® 4-Drawer Rolling Cabinet UltraHD® 6-Foot Height Adjustable Workbench
Model No. 20205 (Granite)
Model No. 20292 (Granite)
UltraHD® Wall Cabinet with Open Shelf UltraHD® 2-Door Rolling Workbench
Model No. 20230 (Granite) Model No. 20262 (Granite)
Model No. 20140 (Graphite) Model No. 20142 (Graphite)
Model No. 20150 (Red) Model No. 20152 (Red)
UltraHD® Rolling Trash Bin UltraHD® Lighted Workcenter
Model No. 20215
Model No. 20247 (Granite)
Model No. 20246 (Graphite)
Model No. 20157 (Red)
UltraHD® Line