SEWOO LK-P32 User manual

All specifications are subject to change without notice
MOBILE PRINTER
MODEL : LK-P32
P32 Rev. A 08/14
SEWOO TECH CO.,LTD.
374-2, Gajang-dong, Osan-si, Gyeonggi-do, 447-210, Korea
TEL : [phone] FAX : [phone]
www.miniprinter.com

1
Table of Contents
1. Safety Caution 2
2. Unpacking
4
3. Product Overview 5
4. Usage and Installation 6
4-1. Control panel usage 6
4-2. Battery installation 10
4-3. Battery removal 11
4-4. Battery charging 12
4-5. Roll paper installation 13
4-6. Self test 14
5. Peripherals Connection 16
5-1. Bluetooth connection 16
5-2. Interface cable connection 17
6. P rinter Specificaiton 18
6-1. Specification 18

23
For higher reliability and safety, consider the following precautionary measures.
Read and follow the instructions carefully before running of the product.
1. Safety Caution
WARNING
Failure to follow these instructions could result in re, electric shock,
or other injuries, or property damage
Indication
Prohibition
(Potential risk of electric shock or re)
(Potential risk of electric shock or re) (Potential risk of electric shock or re)
(Potential risk of electric shock or re)
Must follow
Do not disassemble Unplug the power from the
outlet
Grounding to prevent electric
shock
Do not handle the product
with wet hands
Do not pull or touch the power plug with
wet hands.
Do not bend the wire and do not allow the
wire to be pressed by heavy object.
If a power plug is broken or a plug is cut or
worn, do not use it.
Do not overload the power plug into one
outlet.
WARNING
Failure to follow these instructions could result in re, electric shock,
or other injuries, or property damage
Failure to follow these instructions could result in re, electric shock,
or other injuries, or property damage
(Turn off the power at installation,
transportation, wiring and inspection.)
(You may get hurt and it can be broken
when it falls)
(Potential risk of re or unit malfunction)
(Potential risk of re or unit malfunction)
(Potential risk of discoloration or
electric shock)
(Potential risk unit malfunction, electric
shock or re. When the product needs
to be repaired, please contact in place
where you ordered.inspection.)
Dealer
Do not pull out the power plug to turn off
the product.
Do not install the product in uneven or
inclined surface.
If the product that needs to be repaired,
please contact in place where you ordered.
Please do not give excessive shock.
Keep product away from the water and
other material.
Do not disassemble, repair or modify the
product.
CAUTION

45
3. Product Overview
Open
button
LCD
Power
button
Battery
USB
Front
Rear
2. Unpacking
Paper feed
button
Control
button
PrinterPrinter
Roll paper
USB Cable
Battery CD
Standard
Charger

67
4-1-1. Printer status icons
4. Usage and Installation
On Line
No Paper
Head Cover Open
Printing
On Line
Bluetooth Battery
No Paper
Cover Open
Now Printing
※
Emulation Information
On Line
ESCPOS
Emulation Information
On Line
CPCL
TPH Overheated
Head Overheated
4-1-2. How to check the remaining power
The battery lamp in LCD signify
the remaining power.
Low Battery
Low Battery
Full Low Battery Flat
4-1 Control panel usage
Button Name function
Power
button
This button is used to turn the printer on and off.
When the printer is off, press this button for approximately
3 seconds and it will turn on the power. When you press
this button in a state that the printer is on, the printer will
turn off.
Paper
feed
button
Paper output can be done manually by pressing this button.
Additionally, self-testing and Hexadecimal Dumping can
be processed..
Press to scroll through the menu choices on the LCD.
Setting Press to select a menu choice on the LCD.

89
4-1-3. Configuration setting
Media : Current Media
Parameter Action/Explanation
Current Media
Displays the Media type that is currently set
Media Type: Journal
BlackMark
Label
To verify Media Type
1. Press button once to display the current
Media type.
Parameter Action/Explanation
Auto Gap or BM (Black Mark) and BAT
(Battery) Calibration
Mode: Gap or BM Calibration
BAT (Battery) Calibration
To Perform Calibration Auto Setting
1. Press button 3 times.
2. Press button to execute Gap or BM
and Battery calibration and wait for 3 seconds.
LCD will display "Are you sure?"
3. Press button to double conrm and printer
will automatically execute auto setting. If not,
wait for 3 seconds without pressing any button.
It will automatically go back to main menu.
※ Navigate the LCD menus by pressing button.
Auto Setting
NOTE
NOTE
To do BAT(Battery) Calibration, REMOVE Battery and use charger only.
In case of using Journal Media mode, Gap or BM calibration will not be displayed.
CAUTION
To change the Media type, use Conguration Tool or LKPxxInitialSetting Utility.
Parameter Action/Explanation
Adjust Print Density
Adjust printing resolution manually.
Density Value: 1~9
To change the value shown
1. Press button twice.
2. Press button to adjust Density.
3. If you do not change any density value,
it will automatically go back to main menu
in 3 seconds.
4. Wait 3 seconds after adjust the density value,
LCD will display "Saving...?".
Then Press button to save or wait
3 seconds not to save.
Manual Setting

10 11
1. Align battery hook as shown in the picture
2. Push the battery into the printer until it locks in place.
As the battery is not charged at the time of your purchase, charge the
battery prior to using the printer
(Use Battery charger or Cradle to charge)
Hook
4-2 Battery installation
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions
Remove the battery holding it up as shown above.
4-3 Battery removal
CAUTION
NOTE

12 13
4-4 Battery charging
1. Unless the exclusive charger is used provided by the manufacturer, the printer
can be damaged, and the manufacturer is not liable for the consequential damage.
2. Before removing the battery, make sure that power is turned off.
3. Printer does not work in the status of being connected with charger only.
4. The battery should be installed to operate printer.
5. While charging, do not turn on the power.
6. Do not operate the print while charging the battery.
7. Do not connect the charger while the printer is operated.
1. Be sure that the printer is turned off
2. After open the USB JACK cover, insert USB JACK into the printer.
3. Plug the power code to electrical outlet.
4-4-1 The status of lamp in charging
Status Charging Charging complete Charging stand by
Charging Lamp Red Green Green
LED
1 2
34
Press the PUSH button to open the
paper cover
Pull a short length of paper out of the
printer and close the cover.
Insert the paper in the right direction
Tear off the additional paper using
tear bar.
4-5 Roll paper installation
NOTE

14 15
1 2
3
Turn off the power pressing the
power button for approximately
3 seconds.
The printout is produced.
While you are pressing the FEED
button, press the power button
4-6 Self test
When the printer is installed initially or when you face a problem, you can run the self
test and check the information about
-Control Circuit, Mechanism, Print Quality, ROM Version
After checking with self-test and no issues are found, you can examine other devices and
software. This function is working independently of devices and software.
● Motor protection from being overheated
The motor should be stopped and cooled about more than 30 seconds after
continuous printing 1.5 meter
The sample of self test printout
1. To print ASCII pattern additionally,
press the Feed button once more
2. After printing ASCII pattern, the
self test will be finished automatically.
3. If the Feed button is not pressed
to print ASCII pattern, self test will
be finished automatically after 30
seconds.
NOTE

16 17
1. Printer can be connected to the PDA and PC which can do wireless
communication.
2. By using Bluetooth function supported in PC, printer can be connected.
This printer can communicate with peripheral devices via Bluetooth and
cables.
5-1 Bluetooth connection
5. Peripherals Connection
Refer to the Bluetooth Manual for more details on connection.
5-2 Interface cable connection
1. Connect USB into the cable connector on the printer.
2. Connect the interface cable into the USB or Serial port
of the device (PDA, PC, etc.)
Use the cable offered by the manufacturer (USB)
USB
NOTE
NOTE

18 19
Printing Method Direct Thermal
Printing Speed Max. 70mm/sec
Resolution 203 DPI X 203 DPI
Character 9Type ( bitmap font)
Character set ALPHA NUMERIC Character, Extension
Character
Barcode EAN-8, EAN-13, Code39, ITF, UPC-A,
Codabar, Code93, Code128
Emulation ESC/POS, CPCL Command Compatible
Driver Windows CE 6.0, Windows Mobile6.0, Android
Sensor Paper End Sensor , Cover Open Sensor ,
Black Mark Sensor, Gap Sensor
Paper Paper type Thermal Paper / Label
Width 79.5mm±0.5mm
Thickness 0.065~0.14mm
External diameter Max. Φ40mm±0.5mm
Internal diameter 18mm ±0.5mm
Reliability TPH 50km
Battery Continuous Printing 40~50min
Standby: 11hour
Communications USB, Bluetooth Class2
Battery Charger Input 100-240V 50/60Hz 0.4A
Output 8.4V 800mA 6.72W LPS
Battery Battery type Li-ion
Output 7.4V , 1400mAH
Charging time 2hours 30min
6. Printer Specification
6-1 Specification
Size W X D X H(mm) 109 X 104 X 48.5
W X D X H” 4.29 X 4.09 X 1.9
Weight 335g (with battery)
Temperature Operation -10 ~ 50℃
Storage -20 ~ 60℃
Humidity Operation 35 ~ 95%
Storage 10 ~ 95%