SGM IDEA SPOT 250 User manual

USER’S MANUAL REL. 1.01
USER’S MANUAL REL. 1.01
SGM TECHNOLOGY FOR LIGHTING SPA VIA PIO LA TORRE, 1 _ 61010 TAVULLIA (PU), ITALY TEL. [phone] _ FAX [phone] www.sgm.it _ [email protected]
GB
I
D
F
E
P
WIT070
MOVING HEADS
IDEA SPOT 250

Vi ringraziamo per aver acquistato un prodotto SGM.
Per ottenere i migliori risultati dal suo utilizzo, vi preghiamo di leggere attentamente questo manuale di istruzioni.
Al suo interno troverete le informazioni tecniche e le specifiche d’uso del prodotto. Nelle pagine in appendice tro-
verete inoltre schemi e diagrammi destinati all’assistenza tecnica.
Nell’ottica di qualità SGM, è possibile che l’Azienda apporti migliorie ai suoi prodotti, per cui consigliamo di alle-
gare il manuale al prodotto stesso e di trascrivere il numero di serie nell’ultima pagina della copertina: utilizzando
il presente manuale con un apparecchio fabbricato prima o dopo la sua stampa, potrebbero esserci discrepanze
fra l’apparecchio e quanto riportato nel manuale stesso.
Thank you for buying an SGM product.
To obtain the best results, please carefully read this instruction manual in which you will find technical information
and specifications for use of the product, as well as diagrams for technical service in the appendix.
In light of SGM quality, the company may make improvements to its products. Therefore, we recommend that the
manual be attached to the product and the serial number copied onto the back cover: using this manual with
equipment manufactured before or after its printing, might show discrepancies between the equipment and the
information listed in the manual.
Wir danken Ihnen für den Kauf eines Produkts von SGM.
Zur Erzielung der besten Resultate bei der Benutzung bitten wir Sie, die vorliegende Bedienungsanleitung aufmerk-
sam zu lesen. Darin finden Sie die technischen Informationen sowie die Anweisungen für die Benutzung des
Produkts. Im Anhang befinden sich auBerdem die Schaltpläne undv Diagramme für den Kundendienst.
SGM behält sich das Recht vor, Verbesserungen an den Produkten vorzunehmen und deshalb empfehlen wir, die
Bedienungsanleitung dem Produkt stets beizulegen und die Seriennummer auf der letzten Seite des Umschlags
einzutragen. Bei der Verwendung dieses Handbuches mit einem Gerät, das vor oder nach der Drucklegung produ-
ziert wurde, können sich Abweichungen zwischen Gerät und dem Inhalt des Handbuches ergeben.
Nous vous remercions d’avoir acheté un produit SGM.
Pour optimiser son utilisation, nous vous prions de bien vouloir lire attentivement cette notice où vous trouverez
les informations techniques et les caractéristiques d’utilisation du produit. En outre, vous trouverez également,
dans les pages en appendice, les schémas et les diagrammes concernant l’assistance technique.
Le concept de qualité SGM, lui permet d’améliorer continuellement ses produits et c’est pourquoi nous vous con-
seillons de joindre la notice au produit et d’inscrire le numéro de sèrie sur la page de couverture. En effet, si on
l’utilise avec un appareil fabriqué avant ou après son impression, il peut y avoir des différences entre l’appareil et
ce qui figure dans la notice.
Les estamos sumamente agradecidos por haber elegido un producto SGM.
Para obtener los mejores resultados, les rogamos leer detenidamente el presente manual de instrucciones. El
mismo contiene las informaciones técnicas y las indicaciones de uso del producto. Las páginas anexas contienen
además los esquemas y diagramas necesarios para la asistencia técnica.
Para mantener la calidad SGM, es posible que la Empresa aporte mejoras sus productos, por ello les aconsejamos
conservar el manual junto con el aparato correspondiente y escribir su número de serie en la última página del
manual; si en cambio se utiliza el presente manual con un aparato frabicado antes o después de su impresión, es
probable que existan discrepancias entre el aparato y las indicaciones del mismo.

GB SGM Technology for Lighting
Idea Spot 250 WIT070 V1.0-01 R
1
Table of Contents
I TRODUCTIO :.............................................................................................................. 2
Features ..................................................................................................................................... 2
SAFETY I STRUCTIO S .................................................................................................... 3
GE ERAL GUIDELI ES ..................................................................................................... 4
I STALLATIO I STRUCTIO S .......................................................................................... 4
a) Installing or replacing the lamp ................................................................................................. 4
b) Mounting the device................................................................................................................. 6
Installation method via clamp ....................................................................................................... 7
DMX-512 control connection.......................................................................................................... 8
Control Board.............................................................................................................................. 9
Main functions........................................................................................................................... 11
I STRUCTIO S O USE: ................................................................................................ 19
ERROR CODES: ............................................................................................................. 22
CLEA I G A D MAI TE A CE........................................................................................ 23
TECH ICAL SPECIFICATIO S .......................................................................................... 23

SGM Technology for Lighting GB
WIT070 V1.0-01 R Idea Spot 250
2
KEEP THIS MANUAL FOR FUTURE NEEDS
For your own safety, please read this user manual carefully before installing the device.
CAUTION !
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing
EVERY PERSO I VOLVED WITH THE I STALLATIO , OPERATIO A D MAI TE A CE OF THIS DEVICE
HAS TO:
- BE QUALIFIED,
- FOLLOW CAREFULLY THE I STRUCTIO S OF THIS MA UAL.
INTRODUCTION:
Thank you for having chosen this professional moving head.
You will see you have acquired a powerful and versatile device.
Unpack the device. Inside the box you should find:
 the fixture device,
 a power cable,
 an XLR connection cable,
 a pair of Quick-lock omega holders,
 a safety cable,
 this manual.
Please check carefully that there is no damage caused by transportation. Should there be any, consult your
dealer and don’t install this device.
Feat res
Lamp: Philips MSD250/2
Control signal : standard DMX-512, 14 channels (16 bit) or 12 channels ( 8 bit)
Stand alone operation with Master/Slave function, sound activated via built in microphone.
Pan and tilt movement :
- 8 bit and 16 bit resolution for smooth and precise motion
- pan : 630° (optional : 540°) rotation , tilt : 265° rotation
- speed of pan/tilt movement adjustable
- scan position memory, auto reposition after unexpected movement
Focus: electronic focus
Strobe/shutter : high speed dual-blade shutter, 0-13Hz or random strobe
Dimmer : mechanical adjust 0%~100%
Colours:1 color wheel with 8 dichroic mirrors plus white, rainbow effect
Gobos: 2 gobo wheels
Rotation gobo wheel: 6 rotating gobos plus open, rotating speed adjustable, and gobo indexing
Fix gobo wheel: 7 fix gobos plus open, both 2 gobo wheels have different speed gobo shake and rainbow effect
Prism: 3- face speed adjustable prism rotates in two directions with 16 prism macro effect
Auto-program: 8 pre-built programs can be selected
Display: Can be changed 180° reverse to fit for different installation position.
Local and remote reset and lamp on/off.
Editable program: Edit and save the program to inside EEPROM via the control board or external controller,
up to 48 scenes can be saved and then can be run in Stand Alone or sound activated.

GB SGM Technology for Lighting
Idea Spot 250 WIT070 V1.0-01 R
3
SAFETY INSTRUCTIONS
CAUTION
Be careful with your operations. With a dangerous voltage you can Suffer
a dangerous electric shock when touching wires!
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe
operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written
in this user manual.
IMPORTANT
Damages caused by the disgregard of this user manual are not subject to warrenty.
The dealer will not accept liability for any resulting defects or problems.
If the device has been exposed to temperature changes due to environmental changes, do not switch it on
immediately. The arising condensation could damage the device. Leave the device switched off until it has
reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case,
replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power cord by the plug. ever pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does not necessarily
mean that the device is defective, it should decrease gradually.
CAUTION
ever touch device during operation!
The housing may heat up.
ever look directly into the light source,
as sensitive persons may suffer an epileptic shock.
Please be aware that damages caused by manual modifications to the device are not subject to warranty.
Keep away from children and non-professionals.

SGM Technology for Lighting GB
WIT070 V1.0-01 R Idea Spot 250
4
GENERAL GUIDELINES
This device is a lighting effect for professional use on stages, in discotheques, theatres, etc.
This fixture is only allowed to be operated with the max alternating current which stated in the technical
specifications in the last page of this manual, the device was designed for indoor use only.
Lighting effects are not designed for permanent operation. Consistent operation breaks may ensure that
the device will serve you for a long time without defects. Do not shake the device.
Avoid brute force when installing or operating the device.
The device shall only be used complete with its protective shield.
While choosing the installation-spot, please make sure that the device is not exposed to extreme heat,
moisture or dust. The minimum distance between light-output from the projector and the illuminated
surface must be more than 0,5 meter.
Always fix the fixture with an appropriate safety cable if you use the quick lock cam in hanging up the
fixture, please make sure the 4 quick lock fasteners turned in the quick lock holes correctly.
Operate the device only after having familiarized with its functions. Do not permit operation by persons not
qualified for operating the device. Most damages are the result of unprofessional operation.
Please use the original packaging if the device is to be transported.
For safety reasons, please be aware that all modifications on the device are forbidden.
If this device will be operated in any way different to the one described in this manual, the product may
suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to
short-circuit, burns, electric shock, lamp explosion, crash, etc.
INSTALLATION INSTRUCTIONS
a) Installing or replacing the lamp
CAUTION
Only install the lamp with the device unplugged from the
mains .
The lamp has to be replaced when it is damaged or deformed.
Before replacing the lamp let the lamp cool down, because during operation, the lamp can
reach very high temperature.
During the installation of the lamps do not touch the glass bulbs bare handed. Always use a cloth to handle
the lamps during insertion and removal.
Do not install lamps with a higher wattage. They generate higher temperatures than which the device was
designed for.

GB SGM Technology for Lighting
Idea Spot 250 WIT070 V1.0-01 R
5
For the installation, you need one Philips MSD 250/2:
Proced res:
1 2
3
4
1
1. . Unscrew the 2 screws (A, B) on the bottom of the housing, holding the plate where the lamp is
underneath.
2
2. . Gently pull the socket holder using the knob in the middle.
3
3. . Carefully insert the lamp into the socket. Please remember there is only one way to insert the lamp.
Gently slide the lamp and its lamp holder back into place and fasten the 2 screws.
4
4. . On the access plate there are 3 small screws marked 1,2 and 3.which are used to adjust the lamp
holder in the lamp housing. You can adjust the 3 screws to fine-turn the position of the lamp to get the
maximum light output as shown below.
AB
Please remember the lamp is not a hot-restrike type, you must wait for approximately 10 minutes after
having turned off the lamp before you can turn it back on again.
CAUTION
Do not operate this device with open cover

SGM Technology for Lighting GB
WIT070 V1.0-01 R Idea Spot 250
6
b) Mo nting the device
CAUTION
Pleas consider the E 60598-2-17 and the other respective
national norms during the installation. The installation must
only be carried out by a qualified person.
The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight
for 1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate safety
cable.
ever stand directly below the device when mounting, removing or servicing the fixture.
The operator has to make sure the safety relating and machine technical installations are approved by an
expert before taking the device into operation for the first time.
These installations have to be approved by a skilled person once a year.
CAUTION
Before taking into operation for the first time, the
installation has to be approved by an expert.
Ca tions:
The effect should be installed outside areas where persons may reach it, walk by or be seated.
CAUTION
When installing the device, make sure there in no highly
inflamm able material within a distance of min. 0,5m
Overhead mounting requires extensive experience, including amongst others calculating
working load limits, installation material being used, and periodic safety inspection of all
installation material and the device. If you lack these qualifications, do not attempt the
installation yourself. Improper installation can result in bodily injury.
CAUTION
The electric connection must only be carried out by a
qualified electrician.
Before mounting make sure that the installation area can hold a minimum point load of 10 times the
device’s weight.
Connect the fixture to the mains with the power plug.

GB SGM Technology for Lighting
Idea Spot 250 WIT070 V1.0-01 R
7
Installation method via clamp
Please refer to the pict re below:
Screw one clamp each via a M12 screw and nut onto the Omega holders.
Insert the quick-lock fasteners of the first Omega holder into the respective holes on the bottom of the
device. Tighten the quick-lock fasteners fully clockwise. Install the second Omega holder.
Pull the safety-rope through the holes on the bottom of the base and over the trussing system or a safe
fixation spot. Insert the end in the carabine and tighten the safety screw.

SGM Technology for Lighting GB
WIT070 V1.0-01 R Idea Spot 250
8
DMX-512 control connection
The product has a DMX 512 input fitted with standard 5-pin XLR connectors. Screened cables in
compliance with EIA RS-485 specifications and the following characteristics must be used for connections:
- 2 conductors plus screen
- 120 Ohm impedance
- low capacitance
- max. transmission rate 250kBaud.
Cable connections:
see illustration, taking care with the screen, which must be connected to
Pin 1
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment,
such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption
of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω
resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last
fixture in the chain. Please see illustrations below.
CONTROLLER
Projector 3
Starting address 29
Projector 2
Starting address 15
Projector 1
Starting address 1

GB SGM Technology for Lighting
Idea Spot 250 WIT070 V1.0-01 R
9
Projector DMX starting address selection
All fixtures should be given a DMX starting address when using a DMX signal, so that the correct fixture
responds to the correct control signals. This digital starting address is the channel number from which the
fixture starts to ‘’listen’’ to the digital control information sent out from the DMX controller. The allocation
of this starting address is achieved by setting the correct number on the display located on the base of the
device.
You can set the same starting address for all fixtures or a group of fixtures , or make different address for
each fixture individually.
If you set the same address, all the units will start to ‘’listen’’ to the same control signal from the same
channel number. In other words, changing the settings of one channel will affect all the fixtures
simultaneously.
If you set a different address, each unit will start to ‘’listen’’ to the channel number you have set, based on
the quantity of control channels of the unit. That means changing the settings of one channel will affect
only the selected fixture.
In the case of the product, which is a 14 channel fixture, you should set the starting address of the first unit
to 1, the second unit to 15 (14 + 1), the third to 29 (15 + 14), and so on.
Note:
The modes of DMX 512 data and lamp are shown via the display:
.
.
.
.
Lamp on Lamp on
DMX OK DMX OK
NO DMX NO DMX
Lamp off
Lamp off
1. After switching on, the device will automatically detect whether DMX 512 data is received or not. If the
data is received, the display will show "A.001" with the actually set address. If there is no data received
at the DMX-input, the display will flash "A001" with the actually set address.
This situation can occur if:
- the 5 PI XLR plug (cable with DMX signal from controller) is not connected with the input of the device.
- the controller is switched off or defective, if the cable or connector is defective or the signal wires are
swap in the input connector.
It’s necessary to insert the XLR termination plug (with 120 Ohm) in the last lighting in the link in order to
ensure proper transmission on the DMX data link.
2. If the lamp is on, the display will show "A00.1" with the actually set address. If the lamp is off, the
display will show "A001" with the actually set address.
Control Board
The Control Board offers several features: you can simply set the starting address, switch on and off the
lamp, run the pre-programmed program or make a reset.
The main menu is accessed by pressing the Mode/esc-button until the display starts flashing. Browse
through the menu by pressing the Up-button or Down-button. Press the Enter-button in order to select
the desired menu. You can change the selection by pressing the Up-button or Down-button. Confirm
every selection by pressing the Enter-button. You can leave every mode by pressing the
Mode/esc-button . The functions provided are described in the following sections.

SGM Technology for Lighting GB
WIT070 V1.0-01 R Idea Spot 250
10
Defa lt settings shaded.
Note:
By default setting, the lamp is not ignited with power on. Lamp can be turned on via DMX controller.
Main
menu
Sub.
menu Extension Display Function
VALU A001~AXXX (AXXX) DMX address setting
SLAV O /OFF (SLAV) Slave setting
ADDR
EBOC O /OFF Change DMX address via
external controller
ALO (AU-A) Automatic Run in Stand Alone
AUTO MAST (AU-M) Automatic Run as Master
ALO (SO-A) Sound-controlled Run in Stand
Alone
RU
SOU
MAST (SO-M) Sound-controlled Run as
Master
VALU D–XX D-00 (DXXX) Display the DMX 512 value of
each channel
RDIS O /OFF Reverse display
0
MODE
DISP
CLDI O /OFF Shut off LED display
OPE O /OFF Lamp on/off
LAAU O /OFF Lamp automated on with
power
O LI O /OFF Lamp on/off via controller
1
LAMP
DELA D–XX D-05 Delay lamp on
RPA O /OFF Pan Reverse
RTIL O /OFF Tilt Reverse
16BI O /OFF Switch 16 bit/8 bit
DEGR 630/540 Pan degree select
DIMM Slow/Fast Dimmer speed
MIC M-XX Mic sensitivity
AUTO Clos/Hold/Auto/Audi o DMX Status
FA S HIGH/AUTO Fan’s mode select
SPEE SP-1/SP-2 Movement Mode Select
REST Reset
LODA O /OFF Restore factory settings
2
SET
VER V-1.0~V-9.9 Software version
LADJ O /OFF Lamp adjustment
TEST T–01~T–30 Test function of each channel
CODE CXXX Fixture code *code is “C050”
3
ADJU
WHEL
CH01~CH30 XXXX(-128~127) Motor Calibration
MATI 0000~9999(hours) Fixture running time
LATI 0000~9999(hours) Lamp running time
CLMT O /OFF Clear fixture time
4
TIME
CLLT O /OFF Clear lamp time
STEP S–01 ~S–48 Steps of Program Run
REC. RE.XX Auto Save Scene
C–01~C–30 0 1 XX(00~FFH)
3 0 XX(00~FFH)
Edit the channels of each
scene
TIME T XXX(001~999) Time for each scene
5
EDIT SC01
~ SC48
C I O /OFF Edit program via controller

GB SGM Technology for Lighting
Idea Spot 250 WIT070 V1.0-01 R
11
Main f nctions
- Main men 0
1. Press [MODE/ESC] to enter the main menu "MODE" (display flashing)
2. Press [ENTER] and select "ADDR",’’RUN’’ or "DISP" by pressing [UP] or [DOWN] button.
3. Press [ENTER] for selecting the desired sub menu.
- DMX address setting, Slave setting
- DMX address setting
With this function, you can adjust the desired DMX-address via the Control Board.
1. Select ‘’VALU’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows “AXXX” ,“XXX” stands for the DMX address from 001 to 511.
3. Adjust the DMX address by pressing [UP] or [DOWN] button.
4. Press [ENTER] to confirm or pressing [MODE/ESC] to return to main menu.
- Slave setting
With this function, you can define the device as slave.
1. Select ‘’SLAV’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.
3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] to select ‘’OFF’’ if you
don’t.
4. Press [ENTER] to confirm or press [MODE/ESC] to return to main menu.
-DMX address setting via controller
With this function, you can adjust the desired DMX-address via an external controller.
This function can only be activated when the DMX-value of all other channels is set to "0" on the
controller.
Select “EBOC” by pressing [UP] or [DOWN].
Press [ENTER], the display shows “O ” or “OFF”.
Press [UP] to select “O ” if you wish to enable this function or [DOWN] to select “OFF” if you don’t.
Press [MODE/ESC] to confirm.
Press [ENTER] in order to return to the main menu.
On the controller, set the DMX-value of channel 1 to "7".
Set the DMX-value of channel 2 to "7"or "8". When set to "7" you can adjust the starting address
between 1 and 255. When set to "8" you can adjust the starting address between 256 and 511.
Set the DMX-value of channel 3 to the desired starting address. If you want to set the starting address
to 57, set channel 1 to "7", channel 2 to "7" and channel 3 to "57". If you want to set the starting
address to 420, set channel 1 to "7", channel 2 to "8" and channel 3 to "164" (256+164=420).
Wait for approx. 20 seconds and the unit will carry out a reset. After that, the new starting address is
set.

SGM Technology for Lighting GB
WIT070 V1.0-01 R Idea Spot 250
12
- Program R n, Master setting
With the function "RUN", you can run the internal program. You can set the number of steps under Step.
You can edit the individual scenes under Edit. You can run the individual scenes either automatically
(AUTO), i.e. with the adjusted Step-Time or sound-controlled (SOU ). The selection "ALO " means Stand
Alone-mode and "MAST" that the device is defined as master.
1. Select "AUTO" or "SOUN" by pressing [UP] or [DOWN] button.
2. Press [ENTER] for selecting the desired extension menu.
3. Select "ALON" or "MAST" by pressing [UP] or [DOWN] button.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Display the DMX-val e, Reverse display, Sh t off LED display
- Display the DMX 512 val e of each channel
With this function you can display the DMX 512 value of each channel.
1. Select "VALU" by pressing [UP] or [DOWN] button.
2. Press [ENTER] to confirm; the display shows “D-00”. In this setting, the DMX-adjustment of every
channel will be displayed.
3. The display shows "D-XX, “XX” stands for the DMX-value of the selected channel, press [UP] or
[DOWN] button in order to select the desired channel. If you select “D-14” the display will only show
the DMX-value of the 14th channel.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Reverse display
With this function you can rotate the display by 180°.
1. Select "RDIS" by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.
3. Press [UP] to select ‘’ON’’ if you wish to enable this function,or press [DOWN] button to ‘’OFF’’ if
you don’t; the display will rotate by 180
o
.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Sh t off LED display
With this function you can shut off the LED display after 2 minutes.
1. Select "CLDI" by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.
3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you
don’t.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

GB SGM Technology for Lighting
Idea Spot 250 WIT070 V1.0-01 R
13
- Main men 1
1. Press [MODE/ESC] to enter the main menu (display flashing).
2. Press [UP] or [DOWN] button to select ‘’LAMP’’.
- Lamp on/off
With this function you can switch the lamp on or off via the Control Board.
1. Select ‘’OPEN’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.
3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you
don’t.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Lamp a tomated on with power.
With this function you can set the lamp be ignited or not when the fixture is power on.
1. Select ‘’LAAU’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.
3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if
you don’t.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Lamp on/off via external controller
With this function you can switch the lamp on or off via an external controller.
1. Select ‘’ONLI’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.
3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if
you don’t.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Delay lamp on
With this function you can delay the lamp ignition.
1. Select ‘’DELA’’ by pressing [UP] or [DOWN] button.
2. Press [E TER], the display shows “D-XX”,”XX” stands for the version number, e.g. “D-15” (default
setting is 15 minutes for lamp delay time)
3. Press [UP] or [DOW ] to set the desired value for lamp delay time.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Main men 2
1. Press [MODE/ESC] to enter the main menu (display flashing).
2. Press [UP] or [DOWN] button. to select ‘’SET’’.

SGM Technology for Lighting GB
WIT070 V1.0-01 R Idea Spot 250
14
- Pan Reverse
With this function you can reverse the Pan-movement.
1. Select ‘’RPA ’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.
3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you
don’t.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Tilt Reverse
With this function you can reverse the Tilt-movement.
1. Select ‘’RTIL’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.
3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you
don’t.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Switch 16 bit/8 bit
With this function you can switch the device from 16 bit to 8 bit resolution.
1. Select ‘’16BI’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.
3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press ‘’DOWN’’ button to ‘’OFF’’ if
you don’t.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Pan degree select
With this function you can select pan angle 630
0
or 540
0.
1. Select “DEGR” by pressing [UP] or [DOW ] button.
2. Press [E TER], the display shows “630” or “540”.
3. Press [UP] or [DOW ] button to select “630” or “540”, the default is 630.
4. Press [E TER] to confirm or Press [MODE/ESC] to return to the main menu.
- Dimmer speed select
With this function you can select dimmer speed “slow” and “fast”.
1. Select “DIMM” by pressing [UP] or [DOW ] button.
2. Press [E TER], the display shows “SLOW” or “FAST”.
3. Press [UP] or [DOW ] button to select “SLOW” or “FAST”.
4. Press [E TER] to confirm or Press [MODE/ESC] to return to the main menu.
-Mic sensitivity
With this function you can adjust the sensitivity of the microphone.
1. Select ‘’MIC’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’M-XX’’, ‘’XX’’ stands for the number from 0 to 99.
3. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
-A tomatic R n by no DMX
With this function you can automatic run the device by no DMX.
1. Select ‘’AUTO’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows “CLOS”, “HOLD”, “AUTO” or “AUDI”.
3. Press [UP] or [DOW ] button to select “CLOS”, “HOLD”, “AUTO” or “AUDI”, the default is “HOLD”.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Fan’s mode select
With this function you can select the Fan’s mode.
1. Select “FA S” by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows “HIGH” or “AUTO”.
3. Select “HIGH” or “AUTO” by pressing [UP] or [DOWN] button.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

GB SGM Technology for Lighting
Idea Spot 250 WIT070 V1.0-01 R
15
- Movement mode select
With this function you can select the movement mode.
1. Select “SPEE” by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows “SP-1” or “SP-2”.
3. Select “SP-1” or “SP-2” by pressing [UP] or [DOWN] button.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Reset
With this function you can Reset the device via the Control Board.
1. Select ‘’REST’’by pressing [UP] or [DOWN] button.
2. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Restore factory settings
With this function you can restore the factory settings of the device. All settings will be set back to the
default values (shaded). Any edited scenes will be lost.
1. Select ‘’LODA’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.
3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you
don’t.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Software version
With this function you can display the software version of the device.
1. Select ‘’VER’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display will show ”V-XX”, "XX" stands for the version number, e.g. “V-1.0”,
“V-2.6”.
3. Press [MODE/ESC] to return to the main menu.
- Main men 3
1. Press [MODE/ESC] to enter the main menu (display flashing).
2. Press [UP] or [DOWN] button to select ‘’ADJU’’.
- Lamp adj stment
With this function you can adjust the lamp via the Control Board. The shutter opens and the lamp can be
adjusted. In this mode, the device will not react to any control signal.
1. Select ‘’LADJ’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.
3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to select ‘OFF’
if you don’t.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Test f nction of each channel
With this function you can test each channel on its (correct) function.
1. Select ‘’TEST’’ by pressing [UP] button.
2. Press [ENTER], the display shows ‘’T-XX’’, “X” stands for the channel number.
3. The current channel will be tested.
4. Select the desired channel by pressing [UP] or [DOWN] button.
5. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

SGM Technology for Lighting GB
WIT070 V1.0-01 R Idea Spot 250
16
- Fixt re code and motor fix
1. Select “WHEL” by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows “CODE” or “CH01-CH30”.
3. Select “CODE” or “CH01-CH30” by pressing [UP] or [DOWN] button.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Main men 4
1. Press [MODE/ESC] to enter the main menu (display flashing).
2. Press [UP] or [DOWN] button to select ‘’TIME’’.
- Fixt re r nning time
With this function you can display the running time of the device.
1. Select ‘’MATI’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’XXXX’’, “X” stands for the number of hours.
3. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Lamp r nning time
With this function you can display the running time of the lamp.
1. Select ‘’LATI’’ by pressing [UP] button.
2. Press [ENTER], the display shows ‘’XXXX’’, “X” stands for the number of hours.
3. Press [MODE/ESC] to return to the main menu.
- Clear fixt re time
With this function you can clear the running time of the device.
1. Select ‘’CLMT’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.
3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you
don’t.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.
- Clear lamp time
With this function you can clear the running time of the lamp. Please clear the lamp time every time you
replace the lamp.
1. Select ‘’CLLT’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.
3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you
don’t.
4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

GB SGM Technology for Lighting
Idea Spot 250 WIT070 V1.0-01 R
17
- Main men 5
1. Press [MODE/ESC] to enter the main menu (display flashing).
2. Press [UP] or [DOWN] button to select ‘’EDIT’’.
- Define the n mber of steps in R n
With this function you can define the number of steps in the
Program Run.
1. Select ‘’STEP’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’S-XX’’, “X” stands
for the total amount of steps you want to save, so you
can call up to 48 scenes in ‘’RUN’’. For example if the
“XX” is 05, it means that ‘’RUN’’ will run the first 5
scenes you saved in ‘’EDIT’’.
3. Press [ENTER] to confirm or Press [MODE/ESC] to
return to the main menu.
-A to Save
With this function you can automatic save the number of
steps in the Program Run.
1. Select “REC” by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows “RE.XX”, “XX”
stands for the number from 1 to 400.
3. Press [ENTER] to confirm or Press [MODE/ESC] to
return to the main menu.

SGM Technology for Lighting GB
WIT070 V1.0-01 R Idea Spot 250
18
- Editing the channels of the individ al scenes
With this function you can edit the program to be called up in Run.
a) Editing via the Control Board
1. Select ‘’SC01’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’SCXX’’, ‘’X’’ stands for the scene no. to be edited.
3. Change the scene no. by pressing [UP] or [DOWN] button.
4. Press [ENTER], the display shows ‘’C-X’’, ‘’X’’ stands for the channel no. Such as ‘’C-01’’, it means
you are editing channel 1 of the selected scene.
5. Select the channel no. you would like to edit by pressing [UP] or [DOWN] button.
6. Press [ENTER] to enter editing for the selected channel, the fixture reacts to your settings. The
display shows the DMX value of the edited channel. Such as ‘’11XX’’, it stands for in the channel 11 of
the editing scene, the DMX value is XX , XX is a hexadecimal number value ‘’01-FF’’.
7. Adjust the desired DMX value by pressing [UP] or [DOWN] button.
8. Press [ENTER] in order to edit other channels of this scene.
9. Repeat steps 5-9 until you finish setting all the DMX values for all channels of this scene.
10. Once all the channels completed, the display will flash ‘’TIME’’
11. Press [ENTER] to edit the time needed, the display shows “TXXX” , “XXX” stands for the time needed
to run the current scene, value “001-999”. E.g., “002” means you need 0.4ms (002*0.2ms) to run the
current scene.
12. Adjust the desired time by pressing [UP] or [DOWN] button.
13. Press [ENTER] to save the settings for the scene you are editing, the display will change to the next
scene automatically.
14. Repeat step 3-14 to edit and other scenes, you can edit and save a maximum of 48 scenes.
15. Press [MODE/ESC] to exit. The number of steps can be defined under ‘STEP’ and the scenes can be
called up under ‘’RUN’’
b) Editing via the external controller
Call p the first scene in yo r controller now.
1. Select ‘’SC01’’ by pressing [UP] or [DOWN] button.
2. Press [ENTER], the display shows ‘’SC01’’.
3. Press [ENTER], the display shows ‘’C-01’’.
4. Select "CNIN" by pressing [UP] or [DOWN] button.
5. Press [ENTER], the display shows "OFF".
6. Press [UP] or [DOWN] button .the display shows "ON".
7. Press [ENTER], the display shows "SC02". You successfully downloaded the first scene.
8. Adjust the Step-time as described above under point 12.
9. Call up the second scene in your controller now.
10. Repeat steps 5-11 until all desired scenes are downloaded.
11. Press [MODE/ESC] to exit. The number of steps can be defined under ’STEP’ and the scenes can be
called up under ‘’RUN’’