Sharp AR-M355N User manual

Why the AR-M355N/M455N …
Targeted for busy mid-volume environments, the
AR-M335N/M445N Digital Multifunctional IMAGERs
offer powerful Multitasking, Advanced Application
Integration and Leading Edge Security. The base
model is comprised of a newly engineered 300 MHz
Multi-tasking Controller, an integrated PCL6
Network Printing System, and 40 GB Hard Disk
Drive that include Sharp’s Document Filing System
combined with a Duplex Single Pass Document
Feeder (DSPF) and on-line paper capacity of up to
3100 sheets.
Each of the host machines is available in three
different configurations:
Package A, AR-M355NA / AR-M455NA
Package B, AR-M355NB / AR-M455NB
Package C, AR-M355NC / AR-M455NC
Base N Model machines include 35/45 PPM engine,
300 MHz multitasking controller, 128 MB memory,
PCL6 printing system, 40 GB hard disk drive (with
document filing), 500-sheet letter size tray, USB2
port, IEEE parallel port, and RJ-45 network
interface.
The AR-M335N/M445N Digital
Multifunctional IMAGER
Features
935/45 ppm print speed
9True multi-tasking engine controller
950-sheet Duplex Single Pass Feeder
9Document filing system
9Permanent Font and Form storage
9Carbon Copy Print mode
9Auto Duplexing on stocks up to 97 lb. index
9IP/MAC Address Filtering (secure NIC card)
9LDAP support with optional Network Scanner
Expansion Kit
9Standard IEEE 1284 and USB 2.0 ports
9New Card Shot feature (copies both sides of
an ID card onto a single sheet of paper)
Scan2 Technology
The new technology enables users to scan both
sides of a 2-sided document in one pass, auto-
duplex documents on paper stocks up to 97 lbs
Index, and offer an array of convenience
features.
Quick Reference Guide: AR-M355N/M455N
Performance, Flexibility,
Productivity, and Security
Powerful Network Connectivity
300 MHz PCL6 Printing System
40 GB Hard Drive
Network Tandem Printing
Flexible Network Scanning
Ability to end to 6 different destinations
allows for a truly digital workflow
¾Send to Desktop
¾Sent to E-mail
¾Send to FTP
¾Send to Group
¾Send to FAX
¾Send to I-FAX
Professional Finishing
Two-Tray Finisher
Saddle-Stitch Finisher
Mail Bin Stacker
Scalable Security Offerings
Confidential Print Feature
User Authentication (E-mail)
IP/MAC Address Filtering
Data Security Kit (128 bit
encryption)
Description: Features & Options
1

Quick Reference Guide: AR-M355N/M455N
Pre-Setup: Tools, Documentation, & Admonitions
Toolbox Basics
Mechanical
• Screwdriver, Phillips #2
• Screwdriver, Flat #1
• Wrench, 1.5mm Hex head
• Feeler gauges
Electrical
• Voltmeter
• ESD wrist or ankle strap
• Approved surge suppressor
• 30x lighted viewing device
Miscellaneous
• Clean, soft, lint-free cloths
• Alcohol
Special Tools & Service Documentation
Electrical/Electronic Component
Admonitions
!
WARNING: Electrical hazard.
Employ proper precautions when
working with high-voltage electrical
equipment.
CAUTION: Improper handling of
electronic components can damage
the equipment.
Properly ground and wear an
electro-static device (ESD) on your
wrist or ankle when working with
electronic modules. Similarly, use
anti-static bags to protect electronic
components during storage or
shipping.
E
S
D
Material Safety Data Sheets
(MSDSs)*
* Download MSDSs at http://www.sharp-service.com
Laser Admonition
For your protection, do
not remove protective
covers or bypass safety
interlocks.
2
SM-AR-FN6*AR-FN7, Saddle Stitch Finisher
SM-AR-MS1*AR-MS1, Mail-bin Stacker
SM-AR-FN7*AR-FN6, Finisher
SM-AR-D28*AR-MU2, Multi-purpose Drawer
SM-AR-D28*AR-D28, Stand/MPD & 2000 Sheet Paper Drawer
SM-AR-D28*AR-D27, Stand/3 x 500 Sheet Paper Drawer
N/A
*AR-TE3, Exit Tray
or
*AR-TE5, Exit Tray/Cabinet
SM-AR-DU3*AR-DU3/DU4, Duplex Unit
SM-ARC355N/ARM455N
Code: 00ZARM455NA1E
AR-M355N/AR-M455N, Service Manual, Circuit Diagram,
and Parts Guide
Part NumberDescription
* Optional equipment
n/aDrumAR-455DR
F-31331Developer (Black)AR-455MD
F-01331Toner cartridge
(Black)
AR-455MT
MSDS
No.
DescriptionProduct Code

Quick Reference Guide: AR-M355N/M455N
Basic System Configuration
System configuration
Basic system
AR-M355N/AR-M455N
(Copier/Network printer model)
Necessary options:
Any one of the stand/MPD & 2000
sheet paper drawer (AR-D28), the
stand/3x 500 sheet paper drawer (AR-
D27), or the multi-purpose drawer
(AR-MU)*
Any one of the upper exit tray
extensions (AR-TE4 or AR-TE5), the
finisher (AR-FN6), the mail-bin stacker
(AR-MS1)
AR-EF3
AR-RK2
* To install the AR-MU2, the exclusive use desk is required.
3

Quick Reference Guide: AR-M355N/M455N
Optional Equipment
Option lineup
Major options
AR-
FX12
Fax expansion kit11
AR-MS1Mail-bin stacker10
AR-FN6Finisher9
AR-FN7Saddle stitch finisher8
AR-DU3Duplex module7
AR-DU4Duplex module/bypass tray6
AR-TE3Exit tray5
AR-TE4
AR-TE5
Upper exit tray extension
or Cabinet exit tray
4
AR-MU2Multi-purpose drawer3
AR-D27Stand/3 x 500 sheet paper drawer2
AR-D28Stand/MPD & 2000 sheet paper drawer1
ModelOption NameNo.
4
or
Exit Tray/Cabinet
(AR-TE5)

Quick Reference Guide: AR-M355N/M455N
Adjustment and Simulation
Adjustment Checklist Simulation
5
Note: For detailed instructions, refer to Section 8
of the AR-M355N/M455N Service Manual.
Entering the Simulation Mode
1. Copy mode key ON →Program key ON →Asterisk (*) key
ON →CLEAR key ON →Asterisk key ON →Ready for
input of a main code of simulation
2. Entering a main code with the 10-key →START key ON
3. Entering a sub-code with the 10-key →START key ON
4. Select an item with the scroll key and the item key.
5. The machine enters the mode corresponding to the
selected item.
a) Press START key or EXECUTE key to start
the simulation operation.
b) To cancel the current simulation mode or to
change the main code or the sub code, press
the user setup key.
*Canceling the simulation mode to return to the
normal mode:
Simulation List
Please refer to the Simulation List (pages 1 through 10) that follows.
6. Press CA key.

Quick Reference Guide: AR-M355N/M455N
Simulation List (Pg. 1 of 10)
Simulation List (Main/Sub)
6
Used to set the warm-up time display YES/NO.8
Used to set the intermittent aging cycle.6
Used to set the operating conditions of aging.17
Used to check the operations of each fan motor and its control circuit.2
Used to check the operation of the paper transport system loads and the control circuit.16
Used to check the operation of the heater lamp and the control circuit.2
Used to check the operation of the display, LCD in the operation panel and control circuit.15
Used to check the operations of the loads in the paper feed section (desk paper feed/large capacity tray) and the related circuit.3
Used to check the operations of the sensors and detectors in the paper feed section (desk paper feed/large capacity tray) and
the related circuit.
24
Used to check the operations of the mail bin stacker loads.21
Used to check the mail bin stacker sensor.20
Console finisher (AR-FN7) adjustment.10
Used to adjust the stacking capacity of the finisher. (Used to adjust the alignment plate [jogger] stop position in the finisher
paper width direction. The adjustment is made by changing the alignment plate home position in the paper width direction by
software.)
6
Used to check the operation of the load in the finisher and the control circuit.3
Used to check the operation of sensor and detector in the finisher and the related circuit.23
Used to check the operations of the loads in the automatic document feeder unit and the control circuits.3
Used to check the operations of the sensors and detectors in the automatic document feeder unit and the related circuits.2
Used to check the operations of the automatic document feeder unit and the control circuit.12
Used to check the operation of sensor and detector in the scanning (read) section and the related circuit.2
Used to check the operations of the scanner (read) unit and its control circuit.11
SubMain
Function (Purpose)Code

Used to check the system configuration (options, internal hardware).10
Used to check the number of use (print quantity) of each paper feed section.9
Used to check the number of use of the finisher, the SPF, and the scan (reading) unit.8
Used to display the key operator code. (This simulation is used when the customer forgets the key operator code.)7
Used to output the list of the setting and adjustment data (simulations, FAX soft switch, counters).6
Used to check the ROM version of each unit (section).5
Used to check the trouble (self-diag) history.4
Used to check misfeed positions and the misfeed count of each position. (if the misfeed count is considerably great, it may be
judged as necessary to repair.)
3
Used to check the total numbers of misfeed and troubles. (When the number of misfeed is considerably great, it is judged as
necessary for repair. The misfeed rate is obtained by dividing this count value with the total counter value.)
2
Used to check the print count value in each section an each operation mode. (Used to check the maintenance timing.)122
Used to set the maintenance cycle.121
Used to cancel the PF troubles (when the copy inhibit command from the host computer is received).017
Used to cancel the self-diag U2 troubles.016
Used to cancel the self-diag “U6-01, 02, 03, F3-12, 22” (large capacity paper feed tray, paper feed trays 1, 2) troubles.015
Used to cancel excluding the self-diag U1/LCC/U2/PF troubles.014
Used to cancel the self-diag “U!” trouble. (Only when FAX is installed.)013
Used to check the operations of the toner motor and the related circuit.110
Used to check the operations of the sensors and detectors in the duplex section and its control circuit.2
Used to check and adjust the operation of the load (clutch/solenoid) in the duplex section and the control circuit.19
Used to check and adjust the operation of the transfer voltage and the related circuit. (Transfer belt cleaning mode.)17
Used to check and adjust the operation of the transfer voltage and the control circuit.6
Used to check and adjust the operation of the main charger grid voltage in each printer mode and the control circuit.2
Used to check and adjust the operations of the developing voltage of each color and the control circuit.18
Quick Reference Guide: AR-M355N/M455N
Simulation List (Pg. 2 of 10)
Simulation List (Main/Sub)
7

Used to make the initial setting of toner concentration when replacing developer.2
Used to check the operations of the developing section (toner concentration, humidity and toner concentration sensor, humidity
sensor, temperature sensor output can be monitored.)
125
Used to clear the counters related to the scan mode and the internet FAX mode.15
Used to reset the OPC drum rotation time, and the DV unit rotation time counter. ; The developer counter in the DV unit installed
Is reset.
11
Used to clear the FAX counter. (Only when FAX is installed.)10
Used clear the printer mode print counter and the self print mode print counter.9
Used to clear the OPC drum counter. (Perform this simulation when the OPC drum is replaced.)7
Used to reset the copy counter.6
Used to reset the developer counter. (The developer counter of the DV unit which is installed is reset.)5
Used to reset the maintenance counter.4
Used to clear the number of use of the finisher, SPF, and the scan (reading) unit.3
Used to clear the number of use (the number of prints) of each paper feed section.2
Used to clear the misfeed counter, the misfeed history, the trouble counter and the trouble history. The counters are cleared
after completion of maintenance.)
1`24
Used o check the operations of the sensors and detectors in the paper feed and transport sections.80
Used to check the trouble history of paper jam and misfeed. (If the number of misfeed and troubles is considerably great, it may
be judged as necessary to repair.)
223
Used to check the values of the counters related to the scan mode and the internet FAX mode.19
Used to check the operating time of the process section (OPC drum, DV unit, toner bottle).13
Used to check the SPF misfeed positions and the number of misfeed at each position. (When the number of misfeed is
considerably great, it can be used as necessary for repair.)
12
Used to check the use frequency (send/receive) of FAX. (Only when FAX is installed.)1122
Quick Reference Guide: AR-M355N/M455N
Simulation List (Pg. 3 of 10)
Simulation List (Main/Sub) (cont’d)
8

Quick Reference Guide: AR-M355N/M455N
Simulation List (Pg. 4 of 10)
Simulation List (Main/Sub) (cont’d)
Used to check the output level of the temperature sensor and the humidity sensor.14
Used to check the data related to the image forming section correction (process correction) result (corrected main charger grid
voltage, the developing bias voltage, and the laser power voltage in each print mode). (This simulation allows to check that
correction is performed normally or not.)
9
Used to set enable/disable of correction operations in the image forming (process) section.144
Used to set the fusing temperature in each operation mode.143
Used to check the operation of the document size sensor and the related circuit. (The document size sensor output level can be
monitored with the LCD display.)
3
Used to adjust the document size sensor sensing level.2
Used to check the operation of the document size sensor and the related circuit. (The operation of the document size sensor
can be monitored with the LCD display.)
141
Used to check the multi-purpose tray width detection adjustment value.12
Used to check the multi-purpose tray width detection adjustment value.11
Used to enter the manual paper feed tray paper width adjustment value.7
Used to adjust the manual paper feed tray paper width detector detection level.2
Used to check the operation of the manual feed tray paper size detector and the related circuit. (The operation of the manual
feed tray paper size detector can be monitored with the LCD display.
140
Used to check the operation of sensors and detectors in the paper feed section and the related circuits.2
Used to check the operation of sensors and detectors in other than the paper feed section and the operations of the related
circuits.
130
Used to set YEZ/NO of toner save operation. (This function is valid only in Japan and UK versions. [Depends on the destination
setting of SIM26-6.] For the other destinations, the same setting can be made by the user program P22.)
18
Used to set the network scanner trial mode.10
Used to set the specifications (paper, document detection, etc.) of the destination.6
Used to set the count mode of the total counter and the maintenance counter.5
Used to set the specification of the auditor. Setting must be made according to the auditor use conditions.326
9

Used to adjust sharpness of the copy mode.31
Used to adjust the gamma (density gradient) of the network scanner mode.27
Used to adjust the scanner exposure level in the ultra fine text mode.25
Used to adjust the scanner exposure level (in the super fine text mode).24
Used to adjust the scanner exposure level in the fine text mode.23
Used to adjust the scanner exposure level in the normal text mode.22
Unused to adjust the scanner exposure level in all the scanner modes.21
Used to adjust the copy density correction into eh SPF copy mode for the document table copy mode. The adjustment is made
so that the copy density becomes the same as that of the document table copy mode.
20
Used to set the auto mode operation specifications in ach mode (copy, scan, FAX).19
Used to adjust the gamma (density gradient) in the copy mode.18
Used to set the gain in shading correction.17
Used to adjust the print density in the FAX mode (each ultra fine mode). (Only when FAX is installed.)16
Used to adjust the print density in the FAX mode (each super fine mode). (Only when FAX is installed.)15
Used to adjust the print density in the FAX mode (each fin mode). (Only when FAX is installed.)14
Used to adjust the print density in the FAX mode (each normal mode). (Only when FAX is installed.)13
Used to adjust the print density into eh FAX mode (all models).12
Used to adjust the print density for each density level (display value) in the copy mode (binary-Photo m ode). An optional print
density can be set for each density level (display value).
11
Used to adjust the print density for each density level (display value) in the copy mode (binary-Text mode). An optional print
density can be set for each density level (display value).
9
Used to adjust the copy density in all the copy modes (Auto, Text, Text/Photo, and Photo mode.246
Used to check the toner concentration control data.16
Used to check the output level of the temperature sensor and the humidity sensor.1444
Quick Reference Guide: AR-M355N/M455N
Simulation List (Pg. 5 of 10)
Simulation List (Main/Sub) (cont’d)
10

Used to adjust the document scan start position. (Used to adjust the scanner scan position into eh SPF mode front scan.)8
Used to enter the SPF width detection adjustment value.7
Used to adjust the DSPF width detection level.653
Used to adjust the contact pressure of paper on the resist roller of each section (each paper feed, duplex feed and SPF paper
feed of the copier). (This adjustment is required when the print image position variations are considerably great or when paper
jams occur too frequently.)
251
Used to adjust the image loss of the scan image in the FAX/scan mode.27
Used to adjust the scan image off-center position. (Adjusted separately for each scan mode.)12
Used to adjust the print image off-center position. (Adjusted separately for each paper feed section.)10
Used to adjust the copy image position and void area (image loss) on print prepare in the copy mode. (The similar adjustment
can be performed with SIM 50-6). (SPF mode.)
7
Used to adjust the copy image position and void area (image loss) on print paper in the copy mode. (The similar adjustment can
e performed with SIM 50-7 [simple method].) (SPF mode).
6
Used to adjust the print image position and the void area (image loss) on print paper. (Adjustment as the print engine.) (This
adjustment is reflected on all the FAX/printer/copy modes.)
5
Used to adjust the document scan position, the image print position, and the void area (image loss). (Simple adjustment) (This
adjustment is the simple method of SIM 50-1.) (Document table mode.)
2
Used to adjust the copy image position and the void area (image loss) adjustment on print paper in the copy mode. (The similar
adjustment can be performed with SIM 50-5 and 50-2 (Simplified method].) (Document table mode.)
150
HSYNC cycle adjustment.6
Used to adjust the copy magnification ratio in the sub scanning direction.5
Used to adjust the copy magnification ratio (in the main scanning and the sub scanning directions).148
Used to adjust sharpness of the scanner mode.46
Used to adjust the image density in the FAX mode (600dpi).45
Used to adjust sharpness of the FAX mode.3946
Quick Reference Guide: AR-M355N/M455N
Simulation List (Pg. 6 of 10)
Simulation List (Main/Sub) (cont’d)
11

Quick Reference Guide: AR-M355N/M455N
Simulation List (Pg. 7 of 10)
Simulation List (Main/Sub) (cont’d)
Used to check the operation of the printer section (self-print operation). (The print pattern, the paper feed mode, the print mode,
the print quantity, and the density can be optionally set).
164
Used to adjust the white plate scan start position for shading. (Document table mode.)7
Used to execute shading.2
Used to check the result of shading correction. (The shading correction data are displayed.)163
Used to delete document filing data. (The management area (standard folder, user folder) is cleared.)11
Used to delete a job complete list (also to delete job log data).10
Used to format the hard disk (the system area excluded).8
Used to check the operation soft the hard disk. (/The result of the self-diag operation of the SMART function is printed out.)7
Used to check the operations of the hard disk. (The self-diag operation of the SMART function I executed.6
Used to check the operations of the hard disk (read/write). (All areas check.)3
Used to check the operation of the hard disk (read/write). (Only in the model with a disk installed). (Partial check.)2
Used to format the hard disk.162
Used to adjust the laser power (absolute value) in the printer mode.4
Used to adjust the laser power (absolute value) in the FAX mode.3
Used to adjust the laser power (absolute value) in the copy mode.2
Used to check the operation of the scanner (write) unit (LSU).161
Used to check the MFP control (DRAM) operations (read/write).160
Used to transfer the MFP controller data. (Used to repair the PWB.)156
Used to set the specifications of the controller operations. (MFP control PWB).3
Used to set the specifications of the scanner control operations. (Scanner control PWB).2
Used to set the specifications of the engine control operations. (PCU-PWB).155
12

Quick Reference Guide: AR-M355N/M455N
Simulation List (Pg. 8 of 10)
Simulation List (Main/Sub) (cont’d)
Used to set the make time in the FAX pulse dial mode (10pps) and to test the dial signal output. (The dial number signals et by
SIM 66-13 is outputted.) Used to check troubles in dialing and to check the operation. (Only when FAX is installed.
14
Used to enter (set) the number of FAX dial signal output test. (The dial number set by this simulation is outputted when the dial
signal output test is made by SIM 66-14-16.) (Only when FAX is installed.)
13
Used to check the output operation of FAX G3 mode 300bps. (Used to check the operation of MODEM.) An output is send at
the send level set by the soft switch. (Only when FAX is installed.)
12
Used to check the output operation of FAX G3 mode 300bps. (Used to check the operation of MODEM.) Send level: Max.
(Only when FAX is installed.)
11
Used to clear all data of the image memory (memory send/receive). The confidential data are also cleared at the same time.
(Only when FAX is installed.)
10
Used to check the output operation of various sound signals of FAX. (Used to check the operation of the sound output IC.) An
output is sent at the send level set by the soft switch. (Only when FAX is installed.)
9
Used to check the output operation of various sound signals of FAX. (Used to check the operation of the sound output IC.)
Send level: Max. (Only when FAX is installed.)
8
Used to print the mage memory data (memory send/receive). (Only when FAX is installed.)7
Used to print the confidential pass code. (Used when the confidential pass code is forgotten.) (Only when FAX is installed.)6
Used to check the output operation of data signals in ach data output mode of FAX. (Used to check the operation of MODEM.)
An output is sent at the send level set by the soft switch. (Only when FAX is installed.)
5
Used to check the output operation of data signals in each data output mode of FAX. (Used to check the operation of MODEM.)
Send level: Max. (Only when FAX is installed.)
4
Used to check the operation of the FAX PWB memory (read/write). (This adjustment is required when the PWB is replaced with
a new one.) (Only when FAX is installed.)
3
Used to clear the FAX soft switch function data and to set to the default. (Excluding the adjustment values.) (Only when FAX is
installed.)
2
Used to change and check the FAX soft switch functions. (Used to change and check the functions provided for the FAX soft
switches.) (Only when FAX is installed.)
166
Used to check the result of the touch panel (LCD display) detection position adjustment. (The coordinates are displayed.)2
Used to adjust the touch panel (LCS display section) detection position.165
13

Quick Reference Guide: AR-M355N/M455N
Simulation List (Pg. 9 of 10)
Simulation List (Main/Sub) (cont’d)
Used to register the FAX number for Model dial-in. (Only when FAX is installed.) Not used in the market. (For development.)25
Used to clear the FAST memory data. (Only when FAX is installed.)24
Used to download the FAX program. (Only when FAX is installed.) Not used in the market. (For development.)23
Used to adjust the handset volume. (Only when the FAX is installed.)22
Used to print information related to FAX (various registrations, communication management, file management, system error protocol).
(Only when FAX is installed.)
21
Used to read the back-up data by SIM 66-19 to the SRAM/HDD. (Only when FAX is installed.)20
Used to back-up the HDD data into the Flash memory (optional FAX expansion memory: AR-MM9). (Only when FAX is installed.)19
Used to check the dial signal (DTMF) output in the FAX tone dial mode. An output is sent at the send level set by the soft switch. Used
to check the operation. (Only when FAX is installed.)
18
Used to check the dial signal (DTMF) output in the FAX tone dial mode. Send level: Max. Used to check the operation. (Only when
FAX is installed.)
17
Used to check the dial signal (DTMF) output in the FAX tone dial mode. (The dial number signal set by SIM 66-13 is outputted. The
send level can be set to an optional level. Used to check troubles in dialing and to check the operation. (Only when FAX is installed.)
16
Used to set the make time in the FAX pulse dial mode (20pps) and to test the dial signal output. (The dial number signal set by SIM 66-
13 is outputted.) The send level can be set to an optional level. Used to check troubles in dialing and to check the operation. (Only
when FAX is installed.)
1566
14

Quick Reference Guide: AR-M355N/M455N
Simulation List (Pg. 10 of 10)
Simulation List (Main/Sub) (cont’d)
Used to set the destination specifications. (Only when FAX is installed.)39
Used to check interface between MFPC controller and MDMC. (Check of the data line or
the command line.) (Only when FAX is installed.)
36
Modem program rewriting. (Only when FAX is installed.) Not used in the market. (For
development.)
35
Used to measure the communication time of test image data. (Only when FAX is
installed.)
34
Used to check the signal (BUSY TONE / CNG / CED / FNET / DTMF) detection. (Only
when FAX is installed.)
33
Used to check the receive data (fixed data) from the line. (Only when FAX is installed.)32
Used to check the relay operation. (Only when FAX is installed.)31
Used to check the change in the TEL/LIU status. (Only7 when FAX is installed.)30
Used to clear data related to an address book (one-touch registration, program
registration/expansion, relay memory box registration, each table content.)
29
Used to register the transfer number for voice warp. (Only when FAX is installed.) Not
used in the market. (For development.)
27
Used to register external telephone numbers for Modem dial-in. (Only when FAX is
installed.) Not used in the market. (For development.)
2666
Used to check the operation of the network card.16
Used to set YES/NO of the parallel I/F select signal of the printer.11
Used to check the operation of the parallel I/F o the printer. (This simulation is for
production only, and requires a special tool for execution.) (Not used in the market.)
267
PIC adjustment value writing. (Only when FAX is installed.)43
PIC program rewriting. (Only when FAX is installed.)42
Used to set the destination specifications. (Only when FAX is installed.)3966
15

AR-455DR (No MSDS required)200KOPC drum (x 1)Drum
AR-455MD / MSDS No. F-313311000K
(100K x
10)
Developer
(Developer: Net weight
500 g) (x 10)
Developer (Black)
AR-455MT / MSDS No. F-01331350K
(35K x 10)
Toner cartridge (with IC)
(x 10)
(Toner: Net weight 750
g)
Toner cartridge (Black)
Product Code / MSDS No.LifeContentDescription
Quick Reference Guide: AR-M355N/M455N
Supplies
Note 1: The other maintenance parts which are not listed above are registered as service parts.
16
Supply System Table

Quick Reference Guide: AR-M355N/M455N
Supplies (cont’d)
17
Maintenance Parts List
Cartridge for AR-FN7AR-SC25000
times
(x 3)
Staple cartridge (x 3)Staple cartridge
Cartridge for AR-FN4
Common with cartridge for AR-
FN6
AR-SC13000
times
(x 3)
Staple cartridge (x 3)Staple cartridge
AR-455CB = (AR-455BL) x 10AR-455CB200K
(x 10)
Cleaner blade (x 10)Cleaner blade
AR-455LH200KLower heat roller (x 1)
Fusing separation pawl (Lower) (x 2)
Lower heat roller kit
AR-455UH200KUpper heat roller (x 1)
Fusing separation pawl (Upper) (x 4)
Upper heat roller kit
*1: Screen grid, charging plate,
MC cleaner unit are included.
AR-455KA1200KCleaner blade (x 1)
Drum separation pawl (x 4)
MC unit *1 (x 1)
Toner receiving seat (x 1)
Side malt F (x 1)
Side malt R (x 1)
Transfer roller (x 1)
Discharge blade (x 1)
Paper dust removing unit (x 1)
DV blade (x 1)
DV side seal F (x 1)
DV side seal R (x 1)
200K Maintenance Kit
RemarksModel NameLifeContentItem
Note: The other maintenance parts which are not listed above are registered as service parts.

Quick Reference Guide: AR-M355N/M455N
Basic Specifications
Engine Copy Speeds (PPM)
18
45ppm35ppm16K
20ppm17ppm8K
20ppm17ppmA3/(11” x 17”)
30ppm25ppmB5R, Executive-R
45ppm35ppmB5
45ppm35ppmA5R/5.5” x 8.5”R,
Invoice-R
30ppm25ppmA4R(8.5”x11”R)
45ppm (40ppm*)35ppm (31ppm*)A4 (8.5” x 11”)
AR-M455NAR-M355NPaper Size
* Paper feed from Manual Bypass Tray

Quick Reference Guide: AR-M355N/M455N
Basic Specifications (cont’d)
AR-M355N = 1440W; AR-M455N = 1440WPower Consumption
100V system (100-127V), 50/60 Hz, Inlet type power cord
Power Source
826 x 665 x 1127mm (32.5” x 26.2” x 44.4”) including
automatic document feeder.
963 x 665mm (37.9” x 26.2”) including automatic document
feeder
Approximately 41.4kg (91 lbs)
Approximately 31.4kg (69 lbs)
Approximately 7.4kg (16 lbs)
Approximately 2lkg (46 lbs)
External Dimensions:
W x D x H:
Occupied Space
Dimensions: W X D:
Weight:
Engine:
Desk:
Rack:
DSPF:
5mm or less
Image Loss (Normal)
Lead Edge: 5mm or less
Rear Edge: 5mm or less
Void Width:
999 sheets
Multi-Copy Max:
About 30 sec. (Under standard condition of 60 seconds left
after side cover opening, polygon motor halt)
Jam Recovery Times:
10.5 sec. (Color)
15.5 sec. (B&W)
First Copy Times:
< 80 secs.
Warm Up Time:
Functional Speeds
19

Quick Reference Guide: AR-M355N/M455N
Cautions for Servicing & Prohibited Printing List
Cautions for Servicing
□Do not touch the photoconductive drum. Scratches or
smudges on the drum will cause dirty printouts.
□The fusing unit is extremely hot. Exercise care in this area.
20
□Do not look directly at the light source of the scanner
module. Doing so may damage your eyes.
□Five adjusters are provided on all optional stand/paper
drawer u nits. These adjusters should be lowered until they
contact the floor.
□Do not make any modifications to this machine. Doing so
may result in personal injury or damage to the machine.
□Since this machine is heavy, it is recommended that it be
moved by more than one person to prevent injury.
□When connecting this machine to a computer, be sure to first
turn both the computer and the machine off.
□Do not throw toner or a toner cartridge into fire. Toner may
be spattered, causing a burn.
□Store toner or toner cartridges in a hard-to-reach place for
child safety.
□Do not print anything that is prohibited from printing by
law.
The following items are normally prohibited from printing
by national law. Other items may be prohibited by local
law.
Prohibited from Printing by Law
• Money
•Stamps
• Bonds
• Stocks
• Bank drafts
• Checks
• Passports
• Driver’s licenses